Is the Exhaust Pipe of the Lynk & Co 01 Hidden?

1 Answers
SanHaley
07/29/25 4:42pm
The Lynk & Co 01 features a dual-exhaust layout with two exhaust pipes. The white version of the Lynk & Co 01 has hidden exhaust pipes, while the red version has exposed ones. The exhaust pipe is part of the engine's exhaust system, which mainly includes the exhaust manifold, exhaust pipe, and muffler. Typically, the three-way catalytic converter, which controls engine pollutant emissions, is also installed in the exhaust system. The exhaust pipe generally consists of a front pipe and a rear pipe. Here are some car exhaust pipe maintenance tips: 1. Waterproofing: When driving in the rain or washing your car, be sure to prevent water from entering the muffler, as this can lead to rust and affect the exhaust pipe's performance. If water accidentally enters the muffler, start the engine immediately to heat it up and expel the accumulated water from the muffler. This is particularly important for exhaust pipe maintenance. 2. Rust prevention: Preventing rust on the car's exhaust pipe isn't just about avoiding water. The best method is to apply anti-rust oil for comprehensive protection. First, remove the muffler and block the drain hole at the bottom. Then, add anti-rust oil to the flange, shake the muffler until the oil evenly coats the inside, and reinstall the muffler. After driving about 20 kilometers, remove the drain hole blockage. Performing this rust prevention maintenance twice a year can significantly reduce the risk of rust. 3. Cleaning: Since the exhaust pipe is often exposed to the outside but is connected to the car's interior, dirt buildup inside can affect its normal function. Improper driving may also allow harmful substances to enter the car, potentially causing more serious issues. Therefore, cleaning the exhaust pipe is an essential part of maintenance.
Was this review help?
15
0
Share
More Forum Discussions

What to Do If Vehicle Fails Emission Test During Annual Inspection?

If a vehicle fails the emission test during annual inspection, the following three methods can be employed: 1. Clean or replace the catalytic converter: The catalytic converter's function is to oxidize CH and CO into CO2 and H2O and reduce NOx into N2, making it crucial for passing emission tests. The catalytic converter is prone to carbon buildup, clogging, poisoning, or failure. Carbon buildup and clogging are reversible and can be restored by cleaning, while poisoning, failure, or damage require replacement. 2. Clean or replace the spark plugs: Faults in the ignition system, such as spark plugs or ignition coils, can also lead to excessive vehicle emissions. Poor spark plug conditions can worsen emission pollution. Spark plugs are also susceptible to carbon buildup, which can be cleaned with sandpaper or cleaning agents to restore their function, and the ignition gap can be adjusted. However, if the spark plugs are found to be eroded or have reached the end of their service life, they should be replaced immediately. 3. Check the oxygen sensor: Oxygen sensors are divided into upstream (front) and downstream (rear) sensors. The upstream sensor monitors the post-combustion gases, and any carbon buildup or malfunction can prevent the ECU from correctly adjusting the air-fuel mixture. The downstream sensor assesses the purification efficiency of the catalytic converter, and if damaged, it cannot determine whether the catalytic converter is functioning properly. Therefore, the oxygen sensor plays a vital role in emission testing, and it is recommended to inspect and clean it along with the catalytic converter.
11
0
Share

Will the driver's license application expire if no test is taken?

According to Article 38 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses", applicants who learn to drive on the training ground and road shall obtain a learning driving certificate in accordance with the regulations. The validity period of the learning driving certificate is three years, and the applicant shall complete the subject two and subject three tests within the validity period. If the test is not completed within the validity period, the results of the subjects that have passed the test will be invalidated. The process of applying for a driver's license: 1. Apply for a driver's license: undergo a physical examination and identity file entry, and after confirmation, officially register for driver's license study. 2. Subject 1: Traffic regulations and related knowledge test, computer-based questions, the content includes precautions for road driving, how to distinguish road safety signs and rules for road driving. 3. Subject 2: Subject 2 is the actual operation in the field, mainly divided into: reversing into the garage, fixed-point parking and starting on the slope, curve driving, side parking, and right-angle turning. 4. Subject 3: Subject 3 is the road test, divided into: preparation for getting on the car, simulated lights, starting, straight-line driving, hundred-meter gear shifting, going straight through the intersection, left turn at the intersection, right turn at the intersection, passing the crosswalk, passing the school area, passing the bus stop, changing lanes, overtaking, turning around, and parking on the side. 5. Subject 4: Safe and civilized driving common sense, mainly in the form of cases, pictures, animations, etc., the question types are judgment questions, single-choice and multiple-choice questions, a total of 50 questions, 100 points are full marks, 90 points are qualified. Each registration has two test qualifications. If you fail, you can register for the second time after 10 days. There are a total of 5 registration qualifications. If you fail five times, you will have to re-register for the driver's license test.
20
2
Share

Can 95 gasoline be used if 92 is regularly used?

92 and 95 gasoline cannot be mixed. Occasionally adding the wrong gasoline grade only requires switching back to the correct grade after use. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended for low-grade gasoline, accidentally using high-grade gasoline will not cause damage, but the increase in octane number will change the fuel's ignition point, leading to delayed combustion in the engine. This means both the engine's power output and thermal efficiency will decrease, with the actual feedback being reduced performance. For vehicles recommended for high-grade gasoline, using low-grade gasoline can cause engine knocking. Because the octane number is too low, the gasoline's ignition point decreases, causing it to ignite prematurely during the compression stroke. If combustion occurs before the spark plug fires during the compression stroke, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. If it's mild knocking, it only increases noise without significant damage to the engine. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring. Besides checking the appropriate gasoline grade in the car's manual, you can also find it on the fuel tank cap, which usually indicates the recommended grade. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with a compression ratio between 8.6-9.9 should use 92 gasoline, while those with a compression ratio between 10.0-11.5 should use 95 gasoline. However, with the use of new technologies, the compression ratio alone cannot determine the gasoline grade. High-compression engines can also be tuned to use low-grade gasoline because, besides the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 gasoline contains 92% isooctane and 8% n-heptane, while 95 gasoline contains 95% isooctane and 5% n-heptane.
11
4
Share

What does AUX mean in Chinese?

AUX is an audio input interface. The basic working principle of the AUX interface is that after connecting to the AUX interface, the audio in electronic products can be connected to the car audio through the headphone jack and AUX interface, allowing the audio to be played on the car audio broadcasting facilities. The USB interface can be used to insert a USB drive for audio playback. When using it, connect one end to the AUX interface and the other end to a video player such as a mobile phone, MP3, or MP4. This allows you to listen to songs or niche music anytime, anywhere, without being limited to car music CDs. However, if the playback device runs out of power, the music will also stop (the interface is generally a 3.5mm standard headphone jack). Aux is the abbreviation for Auxiliary, which is an additional signal line design. In general audio equipment, in addition to the standard output and input terminals, there are often several terminals labeled Aux, serving as backup connection points. When there are special applications, such as additional audio output or input, these terminals can be used. These backup terminals or lines, whether for input or output, are collectively referred to as Aux. Function: The AUX port is an asynchronous port, mainly used for remote configuration, dial-up connections, or connecting with a MODEM via a transceiver. It supports hardware flow control. The AUX port and CONSOLE port are usually placed together because they are used in different configuration environments. The AUX interface establishes a command-line connection between the user and the device, enabling operations that are usually impossible in user mode, such as initialization, restoring initial configurations, or correcting abnormal user modes. It provides a fixed port for the device, which can be used as a standard asynchronous serial port with a maximum speed of 115200bit/s. Using the AUX interface, remote configuration and line backup functions for hardware products can be achieved. Note: When using the AUX interface, make sure to purchase the correct connecting cable and avoid plugging the audio cable into the wrong port. It is best to follow the steps outlined in the product's user manual when using the AUX interface. If you are still unsure, you can consult the product's official website or call for assistance.
12
4
Share

The Function of Gasoline Fuel Additives

Gasoline fuel additives serve the following purposes: 1. Cleaning: Used to remove carbon deposits and clean the fuel system. 2. Performance Enhancement: Improves the power performance of the fuel. 3. Fuel Economy: Enhances atomization and saves fuel. 4. Protection: Provides anti-corrosion and anti-rust effects, as well as excellent lubrication, effectively protecting the engine. 5. Noise Reduction: Reduces noise and minimizes wear and tear on the engine from impurities, thereby extending the engine's lifespan. 6. Emission Reduction: Helps eliminate black smoke and lower emissions.
3
3
Share

How to Open a Truck Door Lock?

Truck door locks can be opened by inserting a mechanical key into the keyhole and turning it. Here are detailed information about trucks: 1. Definition: A truck is a commercial vehicle primarily designed and equipped for transporting goods. Freight vehicles are generally referred to as trucks, also known as lorries, mainly used for transporting goods. Sometimes, they can also refer to vehicles capable of towing other vehicles, categorized into heavy-duty and light-duty types. 2. Precautions: If the car's central control system enters an electronically locked state, or if the door lock cylinder is stuck, it cannot be opened with a mechanical key.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.