Is the engine oil from 4S stores fake?

What Causes a BMW to Shake When Shifting Gears?

When a BMW shakes during gear shifting, it is typically due to interference in the internal coupling or clutch of the transmission. Additionally, if there is friction between the engine, transmission, exhaust pipe, and the underbody or chassis, or if the damping rubber has aged and cracked, the normal vibrations from the engine can directly transmit into the cabin, resulting in shaking during gear shifts. Shifting Posture: When shifting gears, keep your eyes on the road ahead and maintain the correct driving posture. Hold the steering wheel firmly with one hand and lightly grip the gear lever knob with the other. Avoid looking down at the controls to prevent veering off course and potential hazards. If the gear doesn't engage smoothly or if there is gear noise, do not force it. After moving the gear lever to neutral, avoid shaking it back and forth to prevent affecting shift timing and damaging components. After Shifting: Once shifting is complete, do not leave your left foot resting on the clutch pedal, as this can cause partial clutch engagement, increasing mechanical wear. Instead, place your foot on the floor of the driver's compartment. While driving, avoid skipping gears when shifting unless absolutely necessary. When needing to shift into reverse while driving, ensure the car comes to a complete stop before shifting to prevent component damage.

20

0

Share

How is driving against traffic determined?

On roads with solid dividing lines, if a motor vehicle enters the opposite lane. Roads with double solid lines or single solid lines as dividers prohibit crossing the lines. On roads with dashed dividing lines, overtaking by borrowing the opposite lane is allowed. However, if an accident occurs and the driver fails to yield to oncoming traffic, the vehicle borrowing the lane will be determined as driving against traffic, with the owner bearing full responsibility. On roads marked with one-way signs, if a motor vehicle enters such a lane, it will be determined as driving against traffic.

2

0

Share

What Causes Mercedes-Benz Bluetooth Connection Failure?

Mercedes-Benz Bluetooth connection failure may occur due to existing connection records between your phone and other devices, or an excessive number of stored connections. It is recommended to delete unused Bluetooth devices and attempt reconnection. Bluetooth Connection Steps: Activate the vehicle's Bluetooth via the central control menu, then enable your phone's Bluetooth; Tap "Search for New Devices" under phone Bluetooth settings and select your car's Bluetooth name to initiate pairing; The pairing code displayed on the vehicle's infotainment system should be entered on your phone before pressing the pairing button; The car's Bluetooth will automatically connect upon receiving the correct pairing code; Subsequent connections only require enabling phone Bluetooth - no repetitive setup needed. Reasons for Bluetooth Disconnection: Poor compatibility between systems. Magnetic interference from environments like power substations or signal towers. Disruptions caused by the vehicle's onboard computer or network. Multimedia system malfunctions potentially caused by excessive connection records or programming errors.

17

1

Share

What to Do If There's a Dead Mouse in the Car Air Conditioner?

When removing it, tools suitable for prying are generally needed. If you don't want to pry, try pressing down; pressing down the side clips can help remove it. The air conditioning vents are close to the central control display and speakers. The air vent panel of this car model has an emergency light button; remember to unplug the connector at the back while removing it. After removal, you can rinse it with water, but make sure to dry it thoroughly before reinstalling.

9

2

Share

What to Do When Your Car Gets Flooded?

If water enters the exhaust pipe after driving through water and the engine stalls, do not attempt to restart it forcefully. Immediately call for roadside assistance and wait for help. If the exhaust pipe is not severely flooded, you can inspect the electronic systems yourself, remove accumulated water under the car body, remove the spark plugs to drain some water from the engine, and then reinstall the spark plugs. If the flooding is severe, you will need roadside assistance to tow the car to a repair shop. If the exhaust pipe is flooded, it will require simple cleaning and drying before it can function properly again.

6

2

Share

How to Use the Car Turn Signal Lever?

Nowadays, vehicle light switches are mainly lever-type switches and knob-type switches, with the lever-type being the most common. To turn on the high beams, gently press the lever downward. The knob-type switch only has the high beam setting. Rotate the light control switch handle to the high beam position, and the high beams will turn on. High beams are all activated by moving the lever. Don't assume that a knob-type light switch means there is no lever switch on the left side of the steering wheel; there are still buttons for turn signals and high beams.

18

0

Share

Is the engine oil from 4S stores fake?

What Causes a BMW to Shake When Shifting Gears?

How is driving against traffic determined?

What Causes Mercedes-Benz Bluetooth Connection Failure?

What to Do If There's a Dead Mouse in the Car Air Conditioner?

What to Do When Your Car Gets Flooded?

How to Use the Car Turn Signal Lever?

Can the Nissan Sunny use 95-octane gasoline?

How to Turn on Bluetooth in the 2012 GL8?

How to Deal with Car Scratch Rust Prevention?

What to Do When the Outside of Both Car Windows Fogs Up?