Is the dual-clutch transmission in the Volkswagen Lamando dry or wet?

1 Answers
StRonan
07/29/25 3:27am
Volkswagen Lamando is equipped with a dry dual-clutch transmission. Here are the detailed introductions about Volkswagen Lamando: The difference between dry dual-clutch transmission and wet dual-clutch transmission: The clutch plates of dry dual-clutch transmission are not immersed in transmission oil, while the clutch plates of wet dual-clutch transmission are immersed in transmission oil. Characteristics of Lamando's dry dual-clutch unique technology: Lightweight: The entire transmission of Lamando weighs only about 72 kg. Fast shifting speed: The principle of dry dual-clutch is the same as that of manual transmission, both using clamping friction plates for transmission. The dual-clutch has two clutches, one responsible for odd gears and the other for even gears. Shifting is essentially switching between the clutches.
Was this review help?
8
2
Share
More Forum Discussions

What Causes the ABS Light to Illuminate in Volkswagen Tiguan?

ABS light illumination can occur in various states, each with different fault causes and solutions, as detailed below: State 1: ABS warning light remains constantly illuminated (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the tone ring to restore normal function. Cause 2: Loose connections in the system wiring or poor contact in the ABS relay can lead to signal issues, causing system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple electrical devices are in use, the battery voltage may drop below 10.5V. As the engine speed increases and voltage rises, the ABS light turns off. This can also occur if the ABS system's power supply voltage is too low due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains illuminated after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; or ABS control unit malfunction. Solution: Loosen and retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary. Check for enlarged gaps in connectors. Replace the ABS or ABS/ASR control unit if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: The ABS control unit detects a significant discrepancy between rear and front wheel speeds during high-speed driving. This may also occur due to incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, typically found on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch linkage down fully, then release the pedal to complete self-adjustment. Replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. A lit ABS light indicates a malfunction in the anti-lock braking system, which can lead to wheel lock-up during emergency braking, causing loss of vehicle control and skidding. This poses significant safety risks as the driver may be unable to decelerate or adjust the vehicle's trajectory.
5
5
Share

Where is the one-button start switch for Audi cars?

Audi's one-button start is located on the right side of the steering wheel. Unlike traditional mechanical key ignition methods and conventional starting procedures, simply pressing the one-button start switch can achieve engine start and stop. The following are the features of the one-button start system: 1. The one-button start system allows for engine shutdown with just one press, avoiding the loss or search for keys. 2. The one-button start device is part of a smart car, serving as a button device that simplifies the starting process and can also shut down the engine. 3. The one-button start device can be retrofitted in the original car key lock position or as an independent panel modification.
18
3
Share

What is the vehicle positioning of the BJ80?

BJ80 is a mid-to-large-sized SUV with strong off-road capabilities. Below is relevant information: 1. The BJ80 is equipped with a 2.3-liter turbocharged engine across all models, delivering 231 horsepower and a maximum torque of 345 Nm. This engine features multi-point fuel injection technology and utilizes an aluminum cylinder head with a cast iron cylinder block. It is paired with a 6-speed automatic transmission. 2. The BJ80 employs a double-wishbone coil spring independent suspension at the front and a five-link coil spring non-independent suspension at the rear. It comes with a part-time four-wheel-drive system, which is standard for rugged off-road vehicles. The part-time four-wheel-drive system offers three driving modes: high-speed four-wheel-drive mode, low-speed four-wheel-drive mode, and high-speed two-wheel-drive mode.
11
2
Share

Is the Leiling Electronic Parking Brake Automatic?

Leiling's electronic parking brake activates automatically. When the electronic parking brake is in operation, no manual intervention is required. Simply ensure the vehicle comes to a complete stop, shift into the P (Park) position, and the electronic parking brake will automatically engage. After shifting to P, you can directly exit and lock the vehicle. Key details are as follows: 1. The electronic parking brake employs an integrated caliper design, combining the motor sensor with the brake caliper for electronic control. Traditional parking brakes rely on hydraulic braking with cable mechanisms. While the electronic parking brake's structure is more complex, its operation is remarkably user-friendly. 2. Its advantages include high technological sophistication, giving a premium appearance. Vehicles equipped with electronic parking brakes typically feature an auto-hold system. This function proves exceptionally practical by preventing vehicle rollback during brief stops. The most noticeable improvements are the electronic parking brake's sleeker aesthetics and easier maintenance compared to conventional systems.
19
3
Share

How early can you go for a vehicle inspection?

Vehicle annual inspections can be conducted up to three months before the expiration date indicated on the driving license. It is advisable to go for the inspection two months or slightly more than one month in advance, rather than waiting until just a few days before the inspection deadline. Additionally, before the 10th of each month, inspection stations tend to have relatively lighter workloads, making it an ideal time to avoid queues. The number of vehicles starts to increase from the middle of the month, and the latter part of the month is the peak period. Below is an introduction to the inspection schedules for various types of vehicles: 1. Operational passenger vehicles must be inspected once a year within the first five years; after five years, every six months. 2. Trucks and large or medium-sized non-operational passenger vehicles must be inspected once a year within the first ten years; after ten years, every six months. 3. Small and mini non-operational passenger vehicles must be inspected once every two years within the first six years; after six years, once a year; after fifteen years, every six months.
19
3
Share

What Causes the Squeaking Noise When the Car Air Conditioner is Turned On?

When the car air conditioner is turned on and a squeaking noise occurs, the reasons may include a loose or slipping air conditioner belt, a faulty compressor, or foreign objects in the blower and air ducts. Solutions for the squeaking noise when the air conditioner is on: 1. Clean the air conditioner belt: If the air conditioner pulley and belt slip, a sharp friction noise will be produced during the slipping process. Check if there is oil or dirt on the belt. If the belt is slipping due to oil or dirt, clean it thoroughly. If not, adjust the compressor's position bolts to tighten the belt, which can increase friction. 2. Tighten the belt: If the noise is caused by a loose belt, you can press the belt to check its tension. If it is too loose, tighten it. If the belt has been used for too long, it needs to be replaced. 3. Replace the tensioner pulley: If the belt tensioner pulley is damaged, it can also cause noise and needs to be replaced with a new one. 5. Clean the blower: Foreign objects in the blower and air ducts can also cause noise, so the blower and air ducts need to be cleaned.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.