Is the Driving Test for Subject 2 Conducted Alone in the Car?

1 Answers
VanLorenzo
07/30/25 10:31am
During the Subject 2 driving test, you are alone in the car; for the Subject 3 test, there is a safety officer in the passenger seat. The Subject 2 test is fully monitored by a computer, with no examiner present inside the vehicle, only a surveillance camera positioned at the front right. If you fail the Subject 2 test on the first attempt, you are allowed one retake. If you choose not to retake or fail the retake, the test session ends, and the applicant must reschedule the test after ten days. Below is an introduction to Subject 2: Learning Objectives: Master the basic driving operations and acquire fundamental vehicle control skills; become proficient in basic methods of driving on-site and within designated road areas; develop the ability to properly use vehicle controls and accurately manage the vehicle's spatial position, ensuring precise control over the vehicle's location, speed, and route. Test Scope: The C1 and C2 license tests include five mandatory items: reverse parking, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves (commonly known as S-turns). Some regions may also include a sixth item, such as highway toll card collection.
Was this review help?
7
5
Share
More Forum Discussions

How to Deal with Rainwater Entering a Sedan Car?

When opening the car door, use the mechanical key for safer access. To avoid other potential issues and prevent damage to the car's electrical circuits, always use the mechanical key. While the car interior is generally waterproof, it's essential to inspect electronic components to prevent short circuits. Avoid turning them on immediately; first, test with absorbent materials. Remove all items from the car, as the carpets are usually damp. Use a vacuum to absorb the water, and ensure the seats are dried to prevent mold. Open the car doors and sunroof under sunlight to air out the vehicle. The primary goal is to ensure all moisture is absorbed and then disinfect the car.
12
4
Share

How to Switch the Daytime Running Lights on the 2012 Sagitar?

With the ignition switch turned on, simply rotate the control lever to the corresponding position for turn signals or parking lights to activate the respective lighting. After switching to low beam, push the lever forward to turn on the high beam. Pulling the lever backward activates the high-low beam alternation function. The front and rear fog lights are controlled by the central part of the lighting control lever. Rotate the switch on the lever to the corresponding position to operate them. The AUTO button lighting up indicates that the automatic headlights are activated. Rotate the knob to switch between position lights, automatic headlights, and low beam. Press the graphic button with the letter A located at the bottom left of the center console. The adaptive headlights will automatically turn on when the vehicle negotiates a certain angle of a curve.
16
2
Share

Where is the first aid kit in the Sagitar?

Volkswagen Sagitar does not come with a first aid kit. Vehicle emergency kits are usually placed in the trunk; some cars have them on the sides of the trunk, while others store them in the storage compartment of the trunk lid. Composition of a car first aid kit: A car first aid kit mainly includes bandaging supplies such as elastic headbands, buckle-type tourniquets, elastic bandages, etc., sterile dressings like gauze, bandages, disposable gloves, etc., and tools such as first aid scissors, medical tweezers, safety pins, rescue whistles, etc. Precautions for using a car first aid kit: First aid supplies should be completely sealed before being placed in the first aid box or kit. Even though the first aid box should be waterproof, double protection provides more security for lives in need. Try to choose first aid medicines that do not cause severe allergic reactions, and all medication should be prepared under the guidance of professional medical personnel.
5
4
Share

How to Properly Drive a Scania Truck?

First, press the brake pedal at the marked position in the Scania cockpit; otherwise, you won't be able to start the vehicle. After pressing the brake pedal, click the start button at the marked position to start the vehicle's engine. Once the vehicle is started, pull down the handbrake lever to release the brake. After releasing the handbrake, push the gear lever to the 1st gear position to begin moving. The dashboard is relatively simple: the left dial shows speed and engine RPM, while the top and bottom sections display indicator and warning lights. Speedometer. Turn signal indicator. Display screen. General warnings and indicators. Tachometer. Urea fluid level. Engine coolant temperature. Fuel gauge. Indicator and warning lights. The new-generation Scania multifunction steering wheel has more buttons than the previous version, supporting additional features.
1
3
Share

Why Doesn't the Car Blow Warm Air?

The reasons why a car doesn't blow warm air are as follows: 1. Thermostat failure, causing the cooling system to prematurely enter a large circulation cycle, resulting in no hot air. 2. Dirty or clogged air filter, affecting the efficiency of the warm air. 3. Faulty warm air control button, unable to transmit the corresponding signal for warm air supply, leading to no warm air. 4. Clogged heater core, preventing coolant from flowing through it, resulting in no hot air. Below is the principle of how a car produces warm air: When the car's heating system is operating, the high-temperature coolant from the engine flows through the heater core. At the same time, the air blown by the blower also passes through the heater core, allowing the car's air conditioning vents to blow warm air.
8
4
Share

Can I Keep the Original License Plate When Buying a Used Car?

When transferring ownership of a used car, it is not possible to retain the original license plate number. Details are as follows: 1. According to legal regulations, for non-immediate family transfers, the license plate number must be changed and the original one cannot be retained. 2. If the old car undergoes a transfer of ownership, you can apply for a license plate renewal quota at the vehicle management office. 3. During the application process, you may attempt to request the retention of the original license plate number. 4. If the current vehicle owner's residence is within the jurisdiction of the vehicle management office, the office should confirm the vehicle, verify the vehicle identification number imprint, review the submitted documents and certificates, reclaim the license plate and vehicle registration certificate, determine a new license plate number, note the transfer details in the vehicle registration certificate, and reissue the license plate, registration certificate, and inspection certificate within one day of accepting the application.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.