Is the Changan CS75 engine a Blue Whale?

1 Answers
LeIvan
09/08/25 8:04am
The Changan CS75 engine is a Blue Whale. The relevant introduction of the Changan CS75 engine is as follows: Introduction 1: The Changan CS75 is equipped with the Blue Whale 280T direct-injection turbocharged engine, which is independently developed and produced by Changan. This engine adopts technologies such as a 200bar high-pressure fuel injection system, direct injection, and turbocharging. Among them, the single-cycle 5-time injection technology is the first batch application in TGDI engines in China. Introduction 2: In addition to excellent power performance, the Blue Whale engine of the CS75 also has good fuel economy, and its exhaust emissions meet the National VI standard. At the same time, the NVH performance of this engine is also quite outstanding, with the in-cabin noise level at idle being only 38 decibels, equivalent to the quietness of a bedroom during nighttime sleep.
Was this review help?
19
3
Share
More Forum Discussions

What to Do When Unable to Open the Car Door?

The central locking system of the car door is activated. Use the car key to unlock and then lock it, repeating this action twice. Then locate the central locking button on the left front door trim panel and press it once. If the child lock is engaged, use a flat-head screwdriver to turn the child lock to the off position to open the door. If the door lock cable is malfunctioning, causing the door to be unopenable from both inside and outside, replacing the door lock cable is necessary to restore functionality. In cases where the key is lost or unusable, preventing the door from being opened, prepare valid identification documents such as ID card, driver's license, and vehicle registration certificate, then contact a locksmith company for assistance.
3
5
Share

How to Remove Windshield Film Adhesive?

Use a hairdryer to heat until it's too hot to touch, then quickly apply force to peel off the sticker. For residual adhesive, spray with tar cleaner, wait a moment, and wipe off with a damp cloth. First, use a damp towel to wet and soften the paper on the sticker, then rub it off. For residual adhesive, apply essential balm, alcohol, or hand cream, then wipe it away. Use a towel dipped in a small amount of solvent like alcohol or diesel fuel to repeatedly wipe the sticker area. Do not spray directly on the glass, as it may damage the film. Use industrial agents like banana water (used for paint removal) to rub a few times, then rinse clean with water.
5
4
Share

How to remove the gear lever of Chery e5?

First, remove the dust cover of the gear lever by lifting it upwards until it cannot be lifted further. At this point, loosen the dust cover by prying it out with a trim panel tool. Then, rotate the gear lever head counterclockwise along with the dust cover to remove it. There are also one or two fixing screws. Remove the fixing screws and rotate the gear lever head counterclockwise to take it off. After removing the rope, a hexagonal screw will be exposed. Use a hex key to unscrew the hexagonal screw counterclockwise, and the gear lever can then be pulled out.
16
4
Share

How to Install the Front License Plate on a Motorcycle?

The license plate should face outward with characters oriented correctly when mounted on the plate holder or bracket; reverse or upside-down installation is prohibited. The front license plate must be installed in the middle or slightly to the right of the motorcycle's front end, ensuring it does not obstruct safe operation or plate recognition. It should be horizontally level and vertically perpendicular to the ground, with a vertical tilt angle not exceeding 15 degrees (upward tilt may extend up to 30 degrees). During installation, maintain a minimum 5mm clearance between the inner edge of the license plate frame and the registration number characters, avoiding any deformation or obstruction. Its primary function is to identify the vehicle's registered region and enable tracking of ownership and registration details through the plate number.
3
3
Share

What are the steps for disassembling and assembling a Jetta engine?

Remove the fuel pump fuse, start the engine to release fuel pressure, and disconnect the negative battery cable. Disassemble the intake pipe assembly, remove the upper intake manifold assembly, take precautions to prevent debris from entering the passages, and then remove the lower intake manifold assembly. Remove the heated oxygen sensor, detach the exhaust pipe and gasket from the mounting bracket, clean the exhaust manifold sealing surface, and inspect for holes, damage, or cracks. Remove the protective plate to expose the generator belt, take off the belt, remove the engine crankshaft output pulley, and detach the triangular fixing bracket on the engine side. Loosen the cylinder head cover bolts in a diagonal sequence, remove the cylinder head cover, take off the valve cover gasket (ensuring its integrity), and then remove the cylinder head.
14
2
Share

How to Care for Car Color Change Film in Daily Life?

Within one week after applying the car film, it is advisable to park the vehicle in a sunny area to ensure thorough evaporation of moisture trapped under the film. Washing the car is strictly prohibited within three days after applying the film to prevent potential detachment caused by water. Therefore, it's recommended to wash the car before applying the film. After applying the car film, avoid rolling down the windows arbitrarily for 3 days in summer and 7 days in winter. For stains on the car film, gently wipe them off using soft materials such as a clean damp towel, sponge, or soft cloth. Due to weather conditions and other factors, the time required for the moisture under the car film to dry completely may vary, and the appearance of mist-like moisture is a normal phenomenon.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.