Is the BMW 530li an imported car?

Volkswagen Indirect Tire Pressure Monitoring Failure?

Tire pressure monitoring failure can be addressed by using a tire pressure gauge. For the safety of the vehicle owner, it is recommended to promptly visit a 4S shop for repairs. The correct method for using a tire pressure gauge is as follows: 1. The central line of the pressure measurement port should form a 90°-180° angle with the axis of the gauge body: The scale is a quadrangular prism with a range of 0.07Wpa-0.4Wpa. Before reading, gently tap the instrument's casing or surface glass with your finger to eliminate friction in the transmission mechanism. 2. When observing, the pointer should overlap with the mirror pointer: The value indicated by the pointer at this time is the pressure reading, accurate to one decimal place. Read the temperature value on the pressure gauge, precise to one decimal place. 3. Align and press the measurement end notch of the pressure gauge with the tire valve: At this point, the pointer of the tire pressure gauge will deflect, and the indicated value is the inflation pressure of the tire. If the gauge's indicator rod is pushed out by the pressure, the value displayed on the rod is the tire's inflation pressure. The greater the internal pressure, the more the pointer will deflect.

10

1

Share

What to Do When the Turn Signal Automatically Turns Off During a Right Angle Turn?

You need to immediately reactivate the turn signal; otherwise, it will show that the turn signal is not on, resulting in a deduction of ten points. Below are the precautions for the right-angle turn in Subject 2 of the driving test: 1. Before entering the turn: It is crucial to slow down the speed and align the car body properly. 2. When the car body is aligned: The vehicle should slowly move close to the outer edge line of the road while maintaining a proper lateral distance. It is advisable to keep the outer wheels within about 300mm of the outer edge line and proceed parallel. 3. When the front of the car approaches the turning point: Turn the steering wheel sharply without delay. When the front bumper aligns with the turning point, quickly turn the steering wheel to the left (or right) to the maximum position. Avoid pressing the accelerator pedal abruptly. 4. Rear wheels in the rearview mirror: Remember to turn the steering wheel back. When the front of the car approaches the right-angle turning point, promptly turn the steering wheel back. When the front of the car turns to the new direction, gradually straighten the steering wheel to keep the car moving straight. Additionally, you can observe the movement of the rear wheels in the rearview mirror. When the rear wheels are about to pass the turning point, straighten the steering wheel.

10

3

Share

Is Brake Fluid the Same as Brake Oil?

Brake fluid is the commonly referred to brake oil, a liquid medium used in hydraulic braking systems to transmit braking pressure, employed in a vehicle's hydraulic braking system. Introduction to Brake Fluid: Brake fluid is a highly concentrated liquid with strong water absorption capabilities. After a period of use, its water content gradually increases. Brake fluid should be replaced every 2 years or every 40,000 kilometers driven. Alternatively, professional instruments can be used to measure the water content of the brake fluid. If it exceeds 5%, it should be replaced as soon as possible; otherwise, it may affect driving safety. Precautions for Brake Fluid Replacement: During the brake fluid replacement process, if air enters the oil pipe, the brakes may feel softer after replacement, potentially leading to delayed braking or even brake failure. The brake fluid can be replaced using the complete drainage method: open the brake caliper's bleed valve, start the engine, and repeatedly press the brake pedal until no more fluid comes out of the bleed valve, then tighten it. Refill the reservoir with new fluid, repeatedly press the brake pedal until firmness is felt, then loosen the caliper bleed valve to drain the fluid. Once the pedal lowers, quickly tighten the valve. Repeat this process twice until no air bubbles emerge from the fluid. Be sure to check the fluid level in the reservoir, ensuring it does not drop below the minimum mark.

17

5

Share

How often should an Audi battery be replaced?

Audi batteries typically need replacement every 5-6 years. Here are more details about Audi batteries: 1. The Audi battery is installed in the trunk of the car, and you can see it by opening the trunk's partition panel. This helps balance the front and rear weight distribution of the car, thereby improving handling. 2. A battery is primarily made of lead and its oxides, with sulfuric acid solution as the electrolyte. It converts chemical energy into electrical energy. 3. The condition of the battery, whether new or old, affects the duration of continuous power supply. Installing additional electrical equipment not originally present in the car, such as subwoofers, can lead to excessive battery usage and reduce its lifespan.

8

3

Share

What are the steps to replace the coolant?

Anti-freeze replacement method is as follows: Before completely replacing the coolant, conduct a thorough inspection to check for any signs of leakage or cracks in the pipelines, with a special focus on the five-way water pipe. The five-way pipe gets its name from having five connecting interfaces to various parts. The coolant flows through the five-way pipe and is then distributed to different parts of the car to function. If there is any leakage of coolant in this section, replace the water pipe or re-secure the interface as needed. Drain the old coolant and then flush the liquid channels with clean water. Add clean water to the coolant reservoir, then continue to inject water into the reservoir to allow it to continuously flow through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water flowing out from the reservoir will have a faint pink color. Continue adding clean water until clear water flows out. Note: Don’t forget to remove the heater hose and drain the water from the heater core. After draining the water for about an hour, add the new coolant through the radiator hose to allow it to quickly flow into the radiator. Then add another bucket of coolant to the coolant reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. At this point, the coolant level will drop slightly as some air is expelled from the cooling system. Add more coolant until it reaches the "MAXT" mark on the reservoir.

9

3

Share

Reasons for Brake Failure After Replacing Brake Pads on the Huanglong 600

Possible reasons for brake failure after replacing brake pads on the Huanglong 600: 1. Lack of necessary maintenance on the brake system, excessive impurities in the brake master cylinder, poor sealing, failure of the vacuum booster pump, contaminated brake fluid or mixed use of different types of brake fluid leading to vapor lock when heated, leakage in the brake master cylinder or wheel cylinders, air leakage in the air reservoir or pipe connections; 2. Mechanical failure caused by improper operation; 3. Severe overloading, which increases the vehicle's inertia under the effect of gravitational acceleration, directly leading to brake failure.

14

2

Share

Is the BMW 530li an imported car?

Volkswagen Indirect Tire Pressure Monitoring Failure?

What to Do When the Turn Signal Automatically Turns Off During a Right Angle Turn?

Is Brake Fluid the Same as Brake Oil?

How often should an Audi battery be replaced?

What are the steps to replace the coolant?

Reasons for Brake Failure After Replacing Brake Pads on the Huanglong 600

Why Is the Air Conditioning Noise So Loud When Driving?

Can BYD Electric Vehicles Charge Without Turning Off the Engine?

How to Manually Reset the Maintenance Light on a Geely Vision?

How soon can I schedule the Subject 4 test after passing Subject 3 in Xi'an?