Is the Accelerator on the Left or Right?

Is it mandatory to display a probationary driver sign during the driver's license probation period?

During the probation period of a driver's license, it is required to display a probationary driver sign. According to relevant regulations, when driving a motor vehicle during the probation period, a uniform-style probationary driver sign must be affixed or hung at the rear of the vehicle. Failure to do so will result in a fine ranging from 20 to 200 yuan. Below are the relevant regulations: 1. The first 12 months after a motor vehicle driver initially applies for a driver's license or adds a permitted vehicle type is considered the probation period. 2. For those who newly obtain a driver's license for large buses, tractors, city buses, medium-sized buses, or large trucks, within 30 days after the probation period ends, they must take an exam on road traffic safety laws and regulations, safe and civilized driving, emergency handling, and other knowledge, and receive no less than half an hour of traffic accident case warning education. 3. There are many benefits for new drivers to display the 'probationary driver' sign. It can alert all traffic participants, such as other motor vehicle drivers, non-motor vehicle drivers, and pedestrians, allowing them to make cautious and reasonable judgments in advance and take effective avoidance measures to prevent traffic accidents.

10

0

Share

What does the turtle icon on the dashboard mean?

The turtle icon on the dashboard indicates that the vehicle has developed a fault but can still be driven at a limited speed of 10 km/h, allowing you to reach a repair shop. The turtle is a malfunction indicator light. Below is an introduction to malfunction indicator lights: 1. Malfunction indicator lights: These include the engine (exhaust system) warning light, oil system warning light, battery and charging system warning light, etc. 2. These malfunction indicator lights rarely illuminate under normal circumstances, but when they do, it signifies that the vehicle has developed a fault or abnormality. Minor issues may affect driving safety, while major ones could potentially damage the vehicle. Immediate inspection and repair are required, or you should contact the vehicle's brand 4S store for assistance.

8

5

Share

How to Remove the Door Panel of a Focus?

Ford Focus door panel removal steps: 1. First, use a plastic pry tool to pry open the door speaker cover along the edge of the door trim panel speaker cover. After removing the door speaker cover, you will find a cross-head screw; remove it. 2. There is another cross-head screw below the door handle; remove it as well. 3. Then, use the plastic pry tool to pry open the edge of the door trim panel, and remove the internal screws with a screwdriver. 4. After all screws are removed, use two plastic pry tools to start from the bottom of the door panel and sequentially pry open the clips of the door panel. 5. Once all clips are pried open, the door panel can be directly removed.

14

4

Share

Why is there abnormal noise when stepping on the brake of a new car?

The causes and solutions for abnormal noise when stepping on the brake are as follows: 1. Deformation of the brake disc or rust on the surface of the brake disc. Solution: Grind and repair the brake disc. 2. The car is new or the brake pads have just been replaced. Solution: Polish the hardened layer. 3. The brake pads are worn out, and the limit plate directly rubs against the brake disc. Solution: Regularly check the brake pads. Once it is found that the brake pads are only 1/3 of the original width or less than 0.5em, the brake pads need to be replaced in time. 4. The brake shield is loose. Solution: Drive the vehicle to the nearest 4S store or repair shop for reassembly.

2

4

Share

How to Open the Hood of a Santana?

Santana hood opening steps: 1. Locate the comma-shaped lever near the hinge inside the driver's side door (or at the lower left corner of the steering wheel); 2. Pull the lever firmly towards yourself until you hear a 'pop' sound; 3. Reach into the very center front of the hood, feel for a lever, and push it until it stops moving, then lift the hood. The Santana (SANTANA) is a brand vehicle produced by Volkswagen in California, USA. In terms of body dimensions, the Santana measures 4437mm in length, 1706mm in width, and 1469mm in height.

6

3

Share

Does the Jetta Not Have an Anti-Collision Beam?

Jetta does not have an anti-collision steel beam. Here is some relevant information about anti-collision beams: 1. An anti-collision beam is a device used to absorb collision energy when a vehicle is impacted, consisting of a main beam, an energy-absorbing box, and mounting plates that connect to the vehicle. 2. The anti-collision steel beam is a U-shaped channel made from cold-rolled steel plates, connected to the vehicle's frame longitudinal beams. It serves as an important safety device that absorbs and mitigates external impacts, protecting the front and rear of the vehicle body. 3. The primary function of an anti-collision beam is to reduce repair costs during low to medium-speed collisions and, to some extent, minimize injuries to the vehicle's occupants.

17

5

Share

Is the Accelerator on the Left or Right?

Is it mandatory to display a probationary driver sign during the driver's license probation period?

What does the turtle icon on the dashboard mean?

How to Remove the Door Panel of a Focus?

Why is there abnormal noise when stepping on the brake of a new car?

How to Open the Hood of a Santana?

Does the Jetta Not Have an Anti-Collision Beam?

What Causes Steering Wheel Instability During Straight-Line Driving?

What Transmission Does the Bora Use?

What Drives the Camshaft Through the Timing Gear?

What is Tested in Driving License Subject 4?