Is System Initialization Normal After Replacing the Battery in a 10th-Generation Civic?

1 Answers
SamuelLynn
07/25/25 2:54am
System initialization after replacing the battery in a 10th-generation Civic is a normal occurrence, typically caused by sensor reset. Below is a detailed introduction about the Civic: Overview: The Honda Civic (CIVIC) offers multiple models to cater to the preferences of consumers in different countries, including three-door hatchbacks, hardtop coupes, hybrid versions, and five-door sedan versions. The Honda Civic available in the domestic market shares the same production platform as the Dongfeng Honda CR-V, with both vehicles using the same chassis. Other Details: Standard seating capacity is 5. Braking system features four-wheel disc brakes. Top speed is 208 km/h. Fastest acceleration time is 8.7 seconds. Trunk volume is 440 liters. Fuel consumption is 5.7 liters per 100 km. Uses 92-octane or higher gasoline.
Was this review help?
16
5
Share
More Forum Discussions

Is the Tianjin Honda 90 still available as a new car?

Tianjin Honda 90 has been discontinued. Extended information on the maintenance and repair of Tianjin Honda 90 motorcycles: Battery maintenance: Remove the left side cover, for a new motorcycle's battery, add electrolyte between the upper and lower scale marks. It is recommended to charge the new battery for better performance. Use a 0.1A current to charge for 6-7 hours, or a 0.3A current for 3-4 hours. Regularly check the battery, and if the liquid level is below the minimum mark, add distilled water to the specified value. If the battery is low on charge or not used for a long time, it should be recharged. Note that charging produces hydrogen and oxygen, so open flames are strictly prohibited at the charging site. Rear brake adjustment: Support the motorcycle with the main stand. Measure the travel distance from the original position to when the brake starts working when the rear brake pedal is depressed, which should be 20-30mm. If adjustment is needed, the method is the same as for the front brake.
14
0
Share

How much fuel does a 460 horsepower engine consume at idle for one hour?

This fuel consumption has not been calculated, and it is not recommended for drivers to idle in place. There are no legal regulations regarding this in China, but in many foreign countries, idling for more than 3 minutes to warm up the engine can result in fines, and it also causes significant environmental pollution. Idling in place likely consumes a very small amount of fuel, but it is highly detrimental to both the environment and the vehicle, leading to excessive carbon buildup, which can affect the vehicle's normal operation in the future. Additional information: Modern vehicles display instantaneous fuel consumption on the dashboard to inform the driver of the current fuel usage during movement, but most vehicles do not show instantaneous fuel consumption when idling.
11
5
Share

What is the sequence of clutch and handbrake when starting the car?

It's essential to remember the general knowledge for starting the car: first press the clutch, second shift the gear, third turn on the indicator, fourth honk the horn, fifth release the handbrake. Here is some extended knowledge about car starting: Before starting, check if the doors are closed. Ensure the seat belt is fastened before starting, and observe the rearview mirrors to confirm safety on both the left and right sides of the vehicle. Turn on the left indicator in advance before starting, and release the parking brake lever simultaneously when starting. When starting, control the accelerator pedal appropriately, avoiding rapid acceleration to prevent the vehicle from jerking. Use a low gear when starting.
4
2
Share

Pros and Cons of Stage 1 ECU Tuning?

The advantage of ECU tuning is that it can enhance the car's performance and unlock the engine's potential, while the disadvantage is that it may disrupt the vehicle's overall balance. A detailed analysis of the pros and cons is as follows: Advantages of ECU tuning: The most significant benefit is the improvement in the car's power output. Both horsepower and torque can be increased. Generally, naturally aspirated models may see a 5%~10% improvement, while turbocharged models can achieve up to a 30% increase. ECU tuning helps to unleash the engine's potential. Disadvantages of ECU tuning: The biggest drawback is the disruption of the vehicle's overall balance. Remember this: the factory settings are the most balanced parameters set by the manufacturer after considering all aspects. A sudden significant increase in power output will inevitably reduce the engine's lifespan. Note: Not all car models are suitable for ECU tuning. ECU tuning is meant to unlock the engine's potential. However, some engines have no remaining potential, making tuning unnecessary.
14
2
Share

What is the difference between car maintenance at a 4S shop and outside?

4S shop maintenance is more reliable but expensive, while outside maintenance carries higher risks but is cheaper. Here are the specific details: 4S shop maintenance: 4S shops have specialized vehicle inspections for specific car models, professional technicians, and matching tools and equipment, as well as sufficient inventory. Maintenance at a 4S shop is more reliable because they communicate with car manufacturers and have a better understanding of the vehicle's conditions. They also have the corresponding tools for the model, and the parts replaced at a 4S shop are usually genuine. Outside maintenance: Lacks a comprehensive management system, sometimes relying only on experience to determine which parts need replacement, and the replaced parts may not be genuine. The main advantage is lower prices, and the maintenance or repair process is relatively faster. You can choose your own engine oil, even purchase it online and pay a service fee for the repair shop to perform the maintenance. You can also supervise the entire process.
4
1
Share

Which Way to Turn the Key When Turning Off the Car?

When turning off the car, the key should be turned clockwise. More details are as follows: Method of turning the car key to shut off the engine: Manual transmission: Step on the brake to slow down, and when the vehicle is about to stop, you can step on the clutch. Pull up the handbrake and shift into neutral. At this point, you can release the clutch and brake. Turn off all light switches and electrical equipment, and straighten the steering wheel to avoid damage to the steering mechanism. Turn the key to the left to shut off the engine (turn the key counterclockwise). If equipped with a one-button start switch, press it once and adjust the ignition switch to the "OFF" position. Automatic transmission: Step on the brake to bring the vehicle to a complete stop, and shift into neutral (N position). Pull up the handbrake and shift into park (P position), then you can release the foot brake. Turn off electrical equipment and light switches. Similarly, turn the key counterclockwise all the way, or press the one-button start switch to turn off the engine.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.