···
Log in / Register

Is Sunroof Noise Covered Under Warranty?

3 Answers
Minnie
07/29/25 8:46am
Sunroof noise is not covered under warranty. The warranty includes: air filter, oil filter, fuel filter, spark plugs, brake linings, clutch plates, tires, battery, remote control battery, bulbs, wiper blades, fuses, and ordinary relays. Additional information: Causes of sunroof noise: 1. Aging sunroof seal: The sunroof produces sounds similar to broken glass or resonance, usually caused by aging seals. 2. Loose sunroof screws: Loose screws can cause abnormal sounds from the roof and sunroof, and may even lead to the sunroof falling off. 3. Dust particles in the sunroof track: Repeated opening and closing of the sunroof inevitably accumulates dust in the track gaps. When the dust accumulates to a certain extent, friction occurs during opening and closing, resulting in noise.
Was this review help?
2
4
Share
LeDaniella
08/12/25 6:48am
This issue really depends on the situation. If your car is still under warranty, sunroof rattling can most likely be repaired for free, especially if it occurs within the first three years of ownership. I've encountered a similar situation before where the dealership inspected it and replaced the sunroof track seals and brackets at no cost. After all, the sunroof is a core component covered under the vehicle's warranty, and rattling caused by non-human factors is generally considered a quality issue. However, make sure to keep all maintenance records, as some shops might try to blame it on wear and tear to avoid responsibility. Also, this problem tends to occur around rainy seasons, with seal aging being the main cause. I recommend having technicians check the sunroof track cleanliness during every routine maintenance.
Was this review help?
8
3
Share
Expand All
LeAustin
10/05/25 8:17am
We just dealt with this issue at home. The car has been driven for over two years, and the sunroof would creak when going over bumpy roads. We took it to the 4S dealership for inspection, and the technician said it was caused by loose screws in the sunroof frame, which is a manufacturing process issue. They tightened and reinforced it for free under the warranty process. As long as it's not man-made damage during the warranty period, it can be covered, such as children forcibly prying or damage from falling objects, which would definitely require out-of-pocket expenses. However, there are many reasons for the noise, such as aging seals, foreign objects stuck in the tracks, or clogged drainage pipes causing water accumulation and corrosion of parts. It's recommended to get it checked early; delaying might turn a free warranty repair into a costly out-of-pocket major repair.
Was this review help?
20
4
Share
Expand All
More Forum Discussions

How much power can be gained by flashing a Stage 1 tune on a Civic?

Flashing a Stage 1 tune on a Civic typically increases power output by around 210 horsepower. The exact parameters vary depending on the horsepower tuning method, with some reaching 220 horsepower, others 235 horsepower, and even some achieving a more significant boost up to 245 horsepower. The principle of flashing a Stage 1 tune: Flashing a Stage 1 tune primarily involves adjusting the ECU parameters of the vehicle to enhance its power. It's worth noting that this method does not involve modifying the vehicle's hardware. The Stage 1 tune mainly adjusts the engine's fuel injection quantity or ignition timing advance angle, while also requiring adjustments to the engine's air intake volume. This allows the vehicle's latent power performance to be fully utilized. The impact of flashing a Stage 1 tune: It's important to mention that the CVT transmission equipped in the Civic has a limited torque capacity. If the horsepower increase from the Stage 1 tune is too high, it can significantly affect the transmission's performance. After flashing the Stage 1 tune, the vehicle's requirement for fuel quality increases. If the engine previously used 92-octane gasoline, it will now require 95-octane gasoline. This is because the engine's overclocked operation demands higher-quality fuel. Additionally, the engine's temperature requirements become more stringent, necessitating a better cooling system to support the overclocked operation. Otherwise, it could negatively impact the engine's lifespan.
17
2
Share

What Causes the Airbag Light to Illuminate on the Car Dashboard?

Reasons for the airbag light illuminating on the car dashboard: 1. Dashboard self-check. Within a short period after entering the car and starting the ignition, the dashboard performs an automatic check. The airbag light will automatically turn off after the check is completed, which usually takes about 5 seconds. This is a normal phenomenon. 2. False fault. If the battery is low on power, it may also cause the airbag light to illuminate. 3. Actual fault. If the above two reasons are ruled out, it may be due to a circuit malfunction, and the car should be repaired promptly. The airbag system is a passive safety protection system that, when used in conjunction with seat belts, provides effective collision protection for occupants. In the event of a car collision, the airbag can reduce head injuries by 25% and facial injuries by approximately 80%.
19
2
Share

Can Subaru Replace Piston Rings?

Subaru can replace piston rings. Reasons for replacing piston rings: Practice has shown that the wear and failure rate of piston rings is much faster than the rate at which cylinder wear reaches its limit. Therefore, often between two major engine overhauls or during maintenance, since the cylinder liner wear is relatively light and does not require cylinder honing or replacement, the engine's performance can be improved by replacing the piston rings. Precautions for replacing piston rings: Check and adjust the ring end gap, side clearance, elasticity, and leakage rate. Select piston rings that match the repair dimensions of the cylinder and piston. Alternatively, the old top compression ring on the piston can be moved to the first ring groove, and the newly selected rings can be installed in the lower ring grooves. This can prevent poor sealing between the new rings and the cylinder wall, which could lead to gas leakage and oil consumption. Correct the wear ridge at the top of the cylinder. A scraper can be used for this correction. When scraping, start from the inside and scrape outward to avoid damaging the cylinder wall surface. Metal shavings from scraping should be properly handled and must not be allowed to fall into the crankcase. If the wear ridge is not corrected, the new rings will impact the ridge during operation, causing the rings to crack or the ring lands to break, potentially leading to cylinder scoring. The end gap of the new rings should be filed to the correct size based on the cylinder position when the piston is at bottom dead center. Special attention should be paid: do not use the maximum wear point at the cylinder's upper wear ridge as the basis for determining the end gap of the rings.
11
1
Share

How to turn on the ambient lights in the Audi Q5L?

To activate the ambient lighting in the Audi Q5L, simply turn on the main light switch. The ambient lighting serves as decorative lighting to create atmosphere, with colors that can be selected according to the owner's preference, typically including red, blue, green, and others. The newer Audi Q5L models are also equipped with the Quattro Ultra four-wheel drive system. Built on a robust passive safety body structure, it incorporates up to 22 driving assistance features, including the Audi Pre Sense safety system, collision avoidance assist, traffic jam assist, exit warning system, and adaptive cruise control. In terms of technological configurations, except for the entry-level model, the entire lineup comes standard with the Virtual Cockpit.
2
3
Share

What documents are required for the biennial inspection of a new car?

The documents required for the biennial inspection of a new car include: 1. The motor vehicle inspection application form provided on-site by the inspection unit and filled out directly; 2. The motor vehicle driving license; 3. Proof of compulsory traffic insurance; 4. Proof of vehicle and vessel tax payment or tax exemption; 5. The owner's ID card. If someone else is handling the inspection on behalf of the owner, the representative must bring their own ID card; 6. For company-owned vehicles, additional documents are required, including the original driving license, a copy of the compulsory traffic insurance, the organization code certificate of the People's Republic of China with a fresh seal, a power of attorney with a fresh seal, and a copy of the representative's ID card.
13
4
Share

What is the oil viscosity of the Volkswagen Polo?

Volkswagen Polo oil viscosity ranges between 12.5-16.3. Polo maintenance: Use genuine 5W-40 oil, opting for semi-synthetic oil from reputable brands. Alternatively, mineral oil can be used, but the maintenance interval should be shortened to 5,000 kilometers. Semi-synthetic oil can extend the interval to 7,500-10,000 kilometers. It is recommended to use 5W-40 or 10W-40 oil. Oils such as 0W-30 or 0W-20, which are suitable for Japanese cars, are not appropriate for the Polo. Engine oil requirements: The general requirements for the engine are small size, lightweight, compact structure, and high power output, which means the unit friction surface bears a significant load. In addition to frictional heat, the engine is also affected by combustion heat, leading to high temperatures on the friction surfaces. This causes the lubricating oil viscosity to decrease, making it difficult to form an oil film. High-temperature, high-pressure combustion gases in the combustion chamber can leak into the crankcase through the gaps between the piston, piston rings, and cylinder liner. These gases are the result of complete and incomplete combustion of fuel and a small amount of lubricating oil, consisting of gases and certain particulates (soot), which typically become the main components of crankcase blow-by. This contaminates the lubricating oil and, under certain conditions, accelerates its oxidation. The lubricating oil required around the combustion chamber enters through the gaps between the piston and cylinder liner and between the valve stem and valve guide, making oil supply more challenging.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.