Is Shell gasoline of good quality?

1 Answers
VonCaleb
07/30/25 5:23am
Shell gasoline is of good quality. Here is more relevant information: 1. Reasons for good quality: Stable physicochemical properties, better lubricity, high-temperature oxidation resistance, and long oil change intervals. Good low-temperature fluidity, easy engine start in cold weather, and excellent engine cooling performance at high temperatures. Good cleaning performance, reducing carbon deposit formation. Low engine operating resistance, which can slightly reduce gasoline consumption. 2. Royal Dutch/Shell Group: The Shell Group, headquartered in The Hague, Netherlands, and London, UK, was formed by the merger of Royal Dutch Petroleum and the UK's Shell. It is one of the world's leading producers of oil, natural gas, and petrochemicals, as well as the largest retailer of automotive fuel and lubricants globally.
Was this review help?
14
4
Share
More Forum Discussions

How to Clean Asphalt from a Car?

The main component of asphalt is hydrocarbons, which are insoluble in water but soluble in carbon disulfide. If asphalt sticks to your car, simply washing it with water won't remove it, and using tools to scrape it off can easily scratch the car's paint. There are two methods to clean asphalt from a car: 1. Use a tar and asphalt cleaner: First, rinse the asphalt stains on the car with tap water two or three times, then evenly apply the tar and asphalt cleaner to the stains. Let it sit for about 5 minutes, allowing the specialized cleaner to gradually penetrate and dissolve the asphalt dirt. Finally, gently wipe the asphalt off the car's surface with a cleaning cloth to completely remove the asphalt stuck to the car. 2. Use car wax: Car wax has excellent stain-removal properties, and the oils in the wax can quickly dissolve asphalt. Apply the car wax directly to the areas of the car body where the asphalt is located. Under the action of the wax, the stubborn asphalt will gradually fade or even disappear. Finally, rinse off the residual wax and dissolved asphalt from the car's surface with clean water and wipe it dry with a soft towel.
7
4
Share

How to Remove the Rear Seats of an Old Jetta?

Old Jetta rear seat removal steps are as follows: 1. First prepare a wrench and a flat-head screwdriver. 2. Lift the rear seat cushion outward and upward at the joint between the seat and backrest: Note there is a groove on each side at the front of the cushion. 3. Start removing the backrest: There are 3 fixing screws at the bottom of the backrest, remove them with the wrench. 4. Remove the six pillar slots: Facing the backrest, insert the flat-head screwdriver between the pillar and foam towards your direction, push in about an inch deep where there is a clip, press inward, then use the other hand to pull up the pillar to remove it.
14
3
Share

How much gasoline can a Sagitar fuel tank hold?

The fuel tank capacity of the Sagitar is 53 liters. More details about the Sagitar fuel tank are as follows: 1. The Sagitar fuel tank capacity is 53 liters, and the gasoline specification is 92-octane or higher unleaded gasoline. The size of the fuel tank is directly related to the vehicle's fuel consumption, with one full tank supporting a driving distance of approximately 600 kilometers. 2. The actual capacity of the fuel tank is greater than the nominal capacity. According to fuel safety regulations, the national standard stipulates that the nominal capacity of a vehicle fuel tank is 95% of the rated capacity. Therefore, when filling up, the actual fuel volume can exceed the nominal capacity by up to 10%. 3. The fuel tank requires regular cleaning. The fuel tank is equipped with vent holes and fuel lines connecting the tank to the charcoal canister. Prolonged lack of cleaning can lead to clogged fuel lines. When the fuel lines are blocked and the fuel tank pressure becomes too high, the vehicle may experience instability or even fuel tank cracking during driving, resulting in fuel leakage and increased fuel consumption.
7
4
Share

How to Determine if the Wiper Motor is Damaged?

To determine if the wiper motor is damaged, you can observe the following: 1. First, turn the car's ignition switch to the power-on state, then try to open the front hood and activate the wipers. If it's not damaged, you should hear the sound of the motor turning, and the sound is quite noticeable. 2. If there is no sound and a slight burning smell accompanies it, it is likely that the motor is damaged and needs to be checked and repaired at an auto repair shop. The wiper not working is often because the vehicle's circuit system prevents circuit overload, leading to the wiper fuse blowing. Therefore, before determining whether the motor is damaged, you should check the fuse (refer to the manual for details). If it is indeed blown, simply replace it, but remember to turn off all the car's power before replacement.
14
1
Share

How Often Should Water Be Added to a Car Radiator?

The normal capacity of a radiator should be between the MIN and MAX marks. When the water level in the antifreeze tank falls below the minimum mark, it's time to add water promptly. The replacement cycle for radiator antifreeze is generally every two years or every 30,000-40,000 kilometers driven. Vehicles with high usage frequency should consider replacing it earlier. Only antifreeze should be added; never use tap water. Below are some precautions regarding adding water to a car radiator: 1. Choose antifreeze based on the vehicle's origin. Generally, antifreeze for domestic cars and imported cars should not be mixed. Therefore, when purchasing, select the appropriate antifreeze according to your vehicle's origin. This is because the rust inhibitors, defoamers, and colorants in imported cars differ chemically from those in domestic antifreeze. Mixing them can cause chemical reactions, leading to scaling, corrosion, and other adverse effects. 2. Try to choose all-season antifreeze. Most antifreeze products today are all-season, eliminating the hassle of changing antifreeze in winter. 3. Some antifreeze coolants need to be mixed with water in a certain ratio to be effective. Regardless of the type of antifreeze coolant purchased, it's best to read the instructions before use to ensure everything is done correctly.
7
3
Share

What is the minimum ground clearance of the Highlander?

Highlander's minimum ground clearance is 195mm, and it is 205mm when unloaded. Below is a detailed introduction to the Highlander's minimum ground clearance: 1. Minimum ground clearance: This refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. 2. Minimum ground clearance reflects the vehicle's ability to pass over obstacles or uneven ground without collision: The greater the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven ground, but the higher the center of gravity, which reduces stability; the smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven ground, but the lower the center of gravity, which increases stability. 3. The design of minimum ground clearance must consider loading and unloading platforms during transportation: The minimum ground clearance should ensure that the vehicle does not scrape when approaching the edge of a standard sidewalk. Additionally, the value of minimum ground clearance is also related to the vehicle's function and aerodynamics.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.