Is Passing the Subject 2 Driving Test on the First Try Impressive?

1 Answers
MirandaFitz
07/29/25 9:04am
Passing the Subject 2 driving test on the first try is a normal achievement. As long as the student practices attentively and diligently, memorizes the key points of the test, and remains calm during the exam, most can pass on their first attempt. Here’s an introduction to Subject 2: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment. It refers to the field driving skills test. For the C1 license, the test items include five mandatory components: reversing into a garage, parallel parking, stopping and starting on a slope, making a 90-degree turn, and driving through curves (commonly known as S-turns). For the C2 license, the test includes four mandatory components: reversing into a garage, parallel parking, making a 90-degree turn, and driving through curves (commonly known as S-turns).
Was this review help?
9
3
Share
More Forum Discussions

Which Types of RVs Can Be Driven with a C1 Driver's License?

C1 driver's license holders can drive RVs such as Maxus RG10, Yutong B330, Yutong B530, Iveco Type C RV, Great Wall Lanzhou Fengjun C4, and Lanzhou Fengjun C7-A. Below is some information about RVs: Different types of RVs are classified based on vehicle type, weight, length, and the corresponding driving license categories listed in the driving license classification table. 1. Motorized RVs are categorized into large, medium, and micro based on passenger vehicle standards. 2. Trailer RVs must be approved by the MIIT of China and can be registered. The type of driving license required depends on the towing vehicle. 3. The mandatory scrapping age for trailers is 15 years.
4
3
Share

How to Deal with Paint on the Car Surface?

How to deal with paint on the car surface: 1. Spray paint remover on the area where the car has paint stains; 2. Let it sit for five minutes, then wipe the affected area with a cloth; 3. Use a hot towel dipped in alcohol to wipe the area; 4. Repeatedly apply and peel off sticky transparent tape; 5. Use a hair dryer to dry the area and then scrape off the paint with a fingernail. Methods for maintaining the car body: 1. Remove dust from the car body promptly to minimize static electricity attracting dust; 2. Rinse off rain stains with clean water as soon as possible after rain to avoid damaging the paint; 3. Avoid washing the car under direct sunlight or high temperatures; 4. Use clean, soft cloths or sponges to wipe the car to prevent metal shavings or sand particles from scratching the surface.
17
5
Share

Which Mazda vehicles use rotary engines?

Mazda RX series vehicles use rotary engines, which employ triangular rotor rotational motion to control compression and exhaust. Here are the details about Mazda RX: 1. Body dimensions: The 2008 Mazda RX8 manual model measures 4460 mm in length, 1770 mm in width, and 1340 mm in height, with a wheelbase of 2700 mm, a fuel tank capacity of 65 liters, and a curb weight of 1406 kg. 2. Vehicle configuration: The 2008 Mazda RX8 manual model is equipped with a 1.3L naturally aspirated engine, delivering a maximum power of 170 kW at 8200 rpm and a maximum torque of 211 Nm at 5500 rpm.
2
2
Share

What is the strip below the car door called?

The strip below the car door is called a scuff plate or welcome plate. The scuff plate is an automotive accessory used to decorate the door sill area, serving to protect the vehicle body and enhance its appearance. The installation method for scuff plates is as follows: 1. Remove the double-sided tape on the back of the plate and clean the surface; 2. Before pasting, position the scuff plate on the desired installation area and adjust it properly; 3. Once the position is determined, remove the red protective film and paste it. The car door consists of the door body, door accessories, and interior trim panel. Its functions are: to provide access for the driver and passengers, isolate external disturbances, and to some extent, mitigate side impacts to protect the occupants.
9
2
Share

When to Use Hazard Warning Lights?

Hazard warning lights can be used in the following situations: 1. Driving in foggy weather. Due to poor visibility in foggy conditions, not only should the hazard warning lights be turned on, but the fog lights should also be activated to alert passing vehicles and provide illumination for yourself. 2. When a vehicle breaks down or is involved in a traffic accident on the road, the hazard warning lights should be turned on to alert passing vehicles to drive safely. On highways, if a vehicle breaks down or is stopped due to an accident, failure to use the lights and set up warning signs as required will result in a 12-point penalty. 3. When towing a malfunctioning motor vehicle, both the towing vehicle and the towed vehicle should turn on the hazard warning lights to indicate that the vehicle is in an abnormal state.
8
1
Share

What is the function of a motorcycle tensioner?

The function of a tensioner is to guide and maintain tension, ensuring it always remains in the optimal tension state. Below is an introduction to tensioners: 1. Working Principle: A tensioner is a commonly used retaining device in belt and chain transmission systems. Its characteristic is to maintain appropriate tension in belts or chains during transmission, thereby preventing belt slippage or avoiding timing belt teeth from skipping or disengaging. It also prevents chain loosening or detachment and reduces wear on sprockets and chains. 2. Features: In terms of effectiveness, tensioners with spring structures are simple in design and inexpensive, making them widely used. Tensioners with rubber components, due to rubber's excellent elastic properties, have a longer lifespan than spring tensioners. However, they require higher-performance rubber, making them more expensive and less commonly used, typically found in high-end mechanical equipment.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.