Is Overtaking Prohibited in Tunnels?

1 Answers
SanAnna
07/25/25 4:09pm
Tunnels do not allow overtaking because tunnels themselves are very narrow, making overtaking extremely dangerous. If a vehicle occupies the fast lane at a speed below the stipulated limit, affecting the traffic behind, or exceeds the stipulated speed limit by 50%, in addition to a fine, 3 penalty points will be deducted. Precautions for driving in tunnels: Reduce speed and turn on lights before entering the tunnel: If driving during the day, the light suddenly dims upon entering the tunnel, and the human eye often takes a short time to adapt. Therefore, about 100 meters before entering the tunnel, you should reduce speed, increase the following distance, turn on the headlights, and enter the tunnel safely at a relatively slower speed. Maintain a sufficiently safe following distance: Due to the significant difference in light when entering and exiting the tunnel, vision can be temporarily impaired. Many people instinctively brake, and the vehicle behind may also be entering a state of impaired vision. Therefore, maintaining a longer following distance ensures sufficient safety. No lane changes: Due to poor light inside the tunnel, especially at the exit, and typically only two or three lanes, changing lanes is strictly prohibited inside the tunnel. Always drive in your designated lane and do not overtake. Speeding is strictly prohibited: Tunnels usually have strict speed limits, even on highways. Speed limit signs are prominently displayed before entering the tunnel, and some tunnels also have speed limit reminders inside.
Was this review help?
13
2
Share
More Forum Discussions

How to Solve Water Leakage in Volkswagen Lavida Doors?

Check if the drainage holes of the sunroof and doors are blocked. You can find a disposable chopstick, break it, and use the tip of the chopstick to poke the drainage holes under the door. After unclogging the drainage holes, there will be no water accumulation.
5
4
Share

What is the problem when the instrument panel does not receive the EECU message?

The instrument panel not receiving the EECU message indicates that the Vehicle Control Unit (VECU) cannot receive signals from the Engine Control Unit (EECU). This situation is usually caused by loose connectors and should be addressed by a professional technician as soon as possible. Fault line detection for the instrument panel not receiving the EECU message: 1. Disconnect the boost pressure temperature sensor and turn the ignition to the ON position. 2. Measure the resistance between pin 11 (CAN-H) and pin 12 (CAN-L) of the communication diagnostic interface in the cabin as 69 ohms, then turn the ignition to the ON position. 3. Disconnect the VECUSL3 plug and measure the termination resistance between pin 6 and pin 7 as 130 ohms, and between pin 3 and pin 4 as 133 ohms, with no obvious issues found. 4. Disconnect the VECUSL3 plug and turn the ignition to the ON position. Measure the voltage to ground for pin 6 as 1.9V, pin 7 as 3V, pin 3 as 2.4V, and pin 4 as 2.4V. It is determined that the communication voltage from the EECU to the VECU is abnormal. 5. Disconnect the main power supply.
19
2
Share

How to Set Up Volkswagen Electronic Parking Brake?

Depress the brake pedal, start the ignition, then press the electronic parking brake button to release the parking brake, and shift from P gear to other gears. After entering the parking space, keep the brake pedal depressed, shift into P gear, and then press the electronic parking brake button next to the gear shift.
10
0
Share

What is the fault when the XCMG test light stays on?

test is the self-check program of the crane. The test indicator light will illuminate when the crane starts up, and the self-check should be completed within a few minutes at most. If there is a fault or issue, the corresponding indicator light will illuminate. Here is some relevant information: 1. Self-diagnosis: Fault detection refers to when the vehicle is unable to operate normally, the vehicle system determines which part has a problem and notifies the user through indicator lights or other methods. 2. Vehicle dashboard: The instruments on different vehicle dashboards vary, but generally, conventional vehicle instruments include the speedometer, tachometer, oil pressure gauge, water temperature gauge, fuel gauge, charging gauge, etc. In modern vehicles, the dashboard also requires a voltage regulator, specifically designed to stabilize the voltage of the dashboard power supply, suppress fluctuations, and ensure the accuracy of the vehicle instruments. Additionally, most instrument displays rely on sensors. The sensing device changes its resistance value based on the state changes of the monitored object and displays it through the instruments. The most prominent instrument on the dashboard is the speedometer, which indicates the vehicle's speed in km/h (kilometers per hour). The speedometer actually consists of two gauges: one is the speed indicator, and the other is the odometer.
16
3
Share

How to Remove and Install the Volkswagen Roof Handle?

Pull the interior roof handle downward by hand, then take out a flat-head screwdriver and gently pry open these two small covers with it. Retrieve a T-20 Torx bit and use it to remove the screws. Keep the removed screws safely for reinstallation. Hold the left side of the interior roof handle with your left hand and the right side with your right hand, then gently pull it outward.
11
3
Share

How to Escape from a Fire in a Car?

Occupants in the vehicle should quickly exit the driver's compartment or passenger compartment. If the doors cannot be opened, they should break the window glass to escape and then attempt to extinguish the fire. When the cargo on the vehicle catches fire, the driver should remain calm and drive the vehicle to a location with water sources or an open area. Promptly call the 119 emergency number, clearly state the specific location, and wait for rescue and firefighting assistance.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.