Is 'ON' for On or Off?

How Many Times Should a Car Be Started to Ignite?

Under normal circumstances, a car should start with just one ignition attempt. If the car is difficult to start, it may require multiple attempts. The reasons for difficulty in starting a car are as follows: 1. Low concentration of the air-fuel mixture. 2. Poor gasoline atomization. 3. Insufficient ignition energy. 4. Battery issues. 5. Damage or aging of the ignition coil and spark plugs. 6. Dirty throttle, intake, and exhaust systems. 7. Use of substandard gasoline. Solutions for difficult car ignition include: 1. Press the horn to assess the battery's charge level based on the sound. If insufficient, check if the electrolyte level is adequate and inspect the battery casing and plates for damage. 2. Inspect the spark plugs to determine if the issue lies with the ignition system or the fuel supply system based on the spark strength. 3. Remove the spark plugs and turn the engine to diagnose whether the problem is with the fuel supply system or ignition timing based on the dryness, moisture, and smell of the exhaust gases. 4. Remove the engine cover to check the ignition timing. If incorrect, adjust the breaker. If correct, clean the breaker. 5. Use a cylinder pressure gauge to check; if the compression pressure is not less than 6.10 Pascals, it indicates an internal mechanical fault in the engine. 6. Remove the muffler; if there is excessive carbon buildup, it indicates a blockage in the exhaust system. 7. Check the car battery for normal operation and sufficient voltage.

3

2

Share

What is the main function of car ABS?

ABS main functions: Fully utilize the effectiveness of the brakes, shortening braking time and distance. Effectively prevent vehicle skidding and fishtailing during emergency braking, ensuring good driving stability. Allow steering during emergency braking, providing good steering control. Avoid severe friction between tires and the ground, reducing tire wear. ABS classification: ABS is mainly classified by channels. In ABS, the brake pipelines that can independently adjust brake pressure are called control channels. ABS control channels are divided into four-channel, three-channel, two-channel, and single-channel types. Single-channel ABS: Also called one-channel ABS, it has a brake pressure regulator installed in the rear wheel brake main pipe, with a wheel speed sensor mounted on the rear axle differential (or one on each rear wheel). Two-channel ABS: This type of ABS struggles to balance directional stability, steering control, and braking effectiveness, and is rarely used today. Three-channel ABS: Independently controls the two front wheels, while the two rear wheels are controlled together based on the low-select principle (i.e., both wheels are controlled by one channel to ensure the wheel with less traction does not lock), also known as hybrid control. Four-channel ABS: Equipped with four wheel speed sensors, each brake pipeline leading to the four wheel brake cylinders has a brake pressure regulator for independent control, forming a four-channel control system.

12

5

Share

What to Do If the Vehicle's First Maintenance Period Has Passed?

If the car exceeds the first maintenance period, but the time and mileage are not too long and still within the limits allowed by the 4S store, then you can still enjoy free first maintenance, so there's no need to worry. According to industry professionals at 4S stores, the first maintenance period is determined by two indicators: mileage and time, whichever comes first. Exceeding either of these may affect the warranty. Therefore, new car owners should pay close attention to the first maintenance schedule. Below is a related introduction: 1. New Car First Maintenance: The key tasks for the first maintenance of a new car are changing the engine oil and oil filter. The period before the first maintenance is the vehicle's break-in period. During this time, as the engine gradually breaks in, dust, metal wear, carbon deposits, and other mechanical impurities will continuously mix into the engine oil. This is why it's often advised not to drive at high speeds during the break-in period—because the oil contains too many impurities, and high-speed driving can lead to abnormal engine wear. Therefore, changing the oil and filter during the first maintenance is crucial. If the debris and impurities produced by the engine are not promptly removed, they may cause abnormal damage to the internal parts of the cylinders. 2. Chassis Inspection: During the first maintenance, the car will be lifted to inspect the chassis for any scratches, underbody impacts, corrosion, or oil leaks. 3. Tire Inspection: This mainly involves checking whether the tire wear is even. If the wear is uneven, it may indicate that the vehicle has a tendency to pull to one side. Additionally, tire pressure will be checked and adjusted as needed. 4. Computer System Check: Through a computer system check, potential issues with the car can be comprehensively detected, after which the maintenance personnel will address any problems accordingly.

15

0

Share

Should the Trunk Drain Plug Be Removed?

It should be removed. Here are the relevant details: 1. Reason: The rubber drain plugs on a car should generally be removed to facilitate water drainage and prolong the vehicle's lifespan. 2. Timely inspection of drain holes: After purchasing a new car, it is essential to promptly check the drain holes on the doors to ensure they are open. If the drain plug is not removed, water can accumulate in the trunk during rain or car washing, leading to rust over time and negatively impacting the car's longevity. Note that there are multiple drain holes on a car, and each typically has a rubber plug.

12

1

Share

What is the condition of engine misfire?

Engine misfire condition includes: 1. Obvious body shaking in idle state; 2. Evident intermittent exhaust gas flow from the vehicle; 3. Insufficient engine power and shortened oil usage cycle; 4. Engine is prone to stalling during operation. Causes of engine misfire: 1. Large wear gap between cylinder liner and piston ring; 2. Poor fuel atomization due to injector wear. An engine is a machine that converts other forms of energy into mechanical energy, including reciprocating piston engines, Stirling engines, steam engines, jet engines, and electric motors. The term engine can refer to both the power generation device and the entire machine including the power unit.

13

5

Share

What Causes the Shuddering During Dual-Clutch Startup?

The reasons for the shuddering during dual-clutch startup: High temperatures inside the clutch cause slight deformation, and replacing the dual-clutch can resolve the issue. If the shuddering is not significant, replacement may not be necessary immediately, and observation is the primary approach. Dual-clutch transmissions differ from conventional automatic transmissions, combining the advantages of manual and automatic transmissions to provide both comfort and power output. While the engine operates at high speeds, gear shifts are typically achieved by gear and clutch actuators, connected to different input shafts. An increasing number of vehicles are adopting dual-clutch transmissions to ensure a better driving experience, enhancing the overall feel of the car's performance.

2

4

Share

Is 'ON' for On or Off?

How Many Times Should a Car Be Started to Ignite?

What is the main function of car ABS?

What to Do If the Vehicle's First Maintenance Period Has Passed?

Should the Trunk Drain Plug Be Removed?

What is the condition of engine misfire?

What Causes the Shuddering During Dual-Clutch Startup?

Is a driver's license required for car loan application?

Is the car film applied inside or outside the car?

What is the ideal temperature for car air conditioning in summer?

Why Do Some Cars Require 95 Octane Gasoline?