Is Lexus a part of FAW Toyota or GAC Toyota?

What are the reasons for the wiper not cleaning properly when wiping?

The reasons for the wiper not cleaning properly when wiping: 1. The rubber strip of the wiper blade is aged or hardened; 2. The windshield is too dirty. Situations requiring wiper blade replacement: 1. If there are cracks, fissures, aging, rust, deformation, attachments, discoloration, etc., it is recommended to replace the wiper blade promptly; 2. If the rubber strip has detached from the frame, causing slapping against the windshield with each wipe, producing abnormal sounds like jumping or shaking, it is advised to replace the wiper blade; 3. If each wipe leaves scratches on either side or the middle of the glass, it is recommended to replace the wiper blade. There are two types of wiper blades: one is the beam blade (without frame), and the other is the conventional blade (with frame). Currently, the beam blade is more commonly used because, without a frame, it fits better against the windshield, resulting in cleaner wiping.

10

2

Share

Is it necessary to warm up the car in summer?

It is not necessary to warm up the car in summer. Idling to warm up the car is useless for fuel-injected engines, but it was useful for carburetor engines. However, carburetor engines have long been phased out, and no cars use carburetor engines anymore, so there is no need to warm up the car. Idling to warm up the car not only fails to quickly raise the engine temperature but also increases carbon deposits inside the engine. The correct way to drive is to start moving after starting the engine, just avoid driving at excessively high RPMs initially to protect the engine and reduce wear. Once the engine's coolant temperature reaches normal levels, you can then increase the RPMs.

4

Share

What are the reasons for stalling during a hill start?

Reasons for stalling during a hill start: 1. The clutch contact point has not been lifted sufficiently; 2. Releasing the handbrake without giving throttle, causing the vehicle to roll back; 3. Panic braking or lifting the clutch too quickly after the vehicle starts rolling back; 4. Lifting the clutch past the contact point while releasing the handbrake too late during the start. Principle of stalling on a slope: The engine has a minimum operating RPM limit. Below this RPM, the engine's power is insufficient to overcome its own friction, causing it to stall. Methods to avoid stalling on a slope: 1. Apply throttle during a hill start; 2. Release the clutch slowly; 3. Avoid prolonged acceleration by pressing the throttle; 4. Engage the handbrake and shift to neutral; 5. Pay attention to the coordination between throttle and clutch.

6

3

Share

Which Button is for Hill Descent Control?

Hill Descent Control is a button featuring a car on a slope. The Hill Descent Control system, also known as the Downhill Assist System, primarily functions to maintain a low vehicle speed and ensure tire traction on steep downhill roads, allowing the car to safely descend to flat ground. Once the Hill Descent Control is activated, the driver can release all pedals and focus on steering. To use the Hill Descent Control system: Before descending a steep slope, turn on the HDC switch. Then, release the accelerator and brake pedals, and the Hill Descent Control system will begin to operate. The system will immediately deactivate if the brake or accelerator pedal is pressed.

13

4

Share

What does the wrench symbol on the Volkswagen dashboard mean?

When the wrench symbol appears on the Volkswagen dashboard, it indicates that the car needs maintenance, not that there is a fault with the vehicle. This symbol does not affect the normal driving of the car, and it will disappear after the maintenance is completed. The purpose of the maintenance indicator light is to remind the driver to perform maintenance on the vehicle after it has been driven for a certain mileage. Taking the Volkswagen Phideon as an example, the car has a length, width, and height of 5074mm, 1893mm, and 1489mm respectively, with a wheelbase of 3009mm. The car is equipped with a 2.0t turbocharged engine, paired with a 7-speed dual-clutch transmission. This engine has a maximum power of 165kw and a maximum torque of 350nm.

5

Share

What Causes a Car to Suddenly Stall While Driving?

The reasons for a car suddenly stalling while driving: 1. The car's fuel tank is empty; 2. Electrical circuit issues; 3. Ignition coil failure, causing all spark plugs to lose high-voltage electricity; 4. Fuel pump damage preventing oil pumping; 5. Excessive carbon buildup at the throttle; 6. Engine computer failure; 7. Timing belt breakage. Solution for a car suddenly stalling while driving: After noticing the stall, depending on the road conditions, if there is no emergency, you can slowly apply the brakes to prevent a rear-end collision. Once the speed decreases, steer slowly towards the roadside lane. After stopping at the roadside, turn on the hazard lights, set up the warning triangle, and call for a tow truck.

3

5

Share

Is Lexus a part of FAW Toyota or GAC Toyota?

What are the reasons for the wiper not cleaning properly when wiping?

Is it necessary to warm up the car in summer?

What are the reasons for stalling during a hill start?

Which Button is for Hill Descent Control?

What does the wrench symbol on the Volkswagen dashboard mean?

What Causes a Car to Suddenly Stall While Driving?

Why Does the Ignition Coil Fail?

Do You Need to Wash the Car Before Applying Window Tint?

How to turn off the turn signal?

What model of fog lights is used for modifying the Volkswagen New Lavida?