Is Jetta a joint venture brand or an independent brand?

What Causes a Car Navigation Screen to Go Black?

The reasons for a car navigation screen going black are: 1. The navigation device has no power; 2. The navigation device's software is not genuine; 3. The original device does not support the new software after an upgrade; 4. Loose or disconnected wiring at the navigation device's port; 5. Malfunction of the navigation device; 6. Damaged circuit board; 7. Damaged navigation display. The solutions for a black car navigation screen are: 1. Check if there is power; 2. Inspect the navigation device's software; 3. Determine if it's caused by an upgrade; 4. Check if the connections are normal; 5. Try pressing the reset button; 6. Inspect if the circuit board and display are damaged.

5

4

Share

What is the method for removing car window film?

There are two methods for removing car window film: 1. Tear open a corner on the window and slowly peel it off; 2. Use adhesive remover, a scraper, and a cloth to clean off any residual adhesive. The functions of car window film include: 1. Heat insulation and sun protection; 2. UV protection; 3. Safety and explosion prevention; 4. Creating a private space; 5. Reducing air conditioning energy consumption; 6. Enhancing aesthetics. The steps for applying car window film are: 1. Lay two large bath towels on the front hood and dashboard; 2. Cover the seats with seat covers and wrap them tightly with plastic wrap; 3. Thoroughly clean each piece of glass; 4. Spray a small amount of window film installation solution on the outer surface of the window glass; 5. Cover it with a soft template; 6. Cut the window film according to the template.

17

5

Share

What is the function of the P gear in an automatic transmission car?

The function of the P gear in an automatic transmission car is to lock the vehicle's braking device, preventing the vehicle from moving. The method to start an automatic transmission car is as follows: 1. Start the car with the gear in N or P position; 2. After starting the engine, wait a few seconds before shifting gears to allow the transmission to be fully lubricated. Press the brake pedal, shift to the correct gear, release the brake pedal, and the car will start normally; 3. When driving on the road, place the gear shift lever in the D position and gradually increase the throttle; 4. When driving on short and small slopes, place the lever in D or L position and control the throttle to complete the uphill; 5. When driving downhill, use the D gear in combination with the brake to control the vehicle; 6. When driving on snow, place the lever in L position, start with L gear to prevent the drive wheels from slipping, and then shift to D gear after the car starts moving.

9

5

Share

How to Adjust the Rearview Mirrors of a Citroën Sedan?

Adjusting the rearview mirrors of a Citroën sedan depends on different situations: 1. Adjusting the left rearview mirror: For up and down positions, place the distant horizon in the center; for left and right positions, adjust until the car body occupies one-fourth of the mirror's surface. 2. Adjusting the right rearview mirror: Position the horizon at two-thirds of the mirror's height, then adjust the car's edge to occupy one-fourth of the mirror's image. 3. Adjusting the interior rearview mirror: Ensure you can see through the rear window, with the upper and lower spaces adjusted so that the sky and ground each occupy about half of the view. Taking the 2020 Citroën C6 as an example, it is a mid-sized 4-door, 5-seater sedan with body dimensions of length 4980mm, width 1858mm, height 1475mm, and a wheelbase of 2900mm.

3

4

Share

What Causes Heavy Steering Wheel in Cars?

Car steering wheel heaviness can be caused by: 1. Insufficient tire pressure; 2. Replacement with different tire models; 3. Damaged or poorly sealed dust boots; 4. Dirty, insufficient, or air-contaminated power steering fluid; 5. Uncalibrated torque sensor; 6. Deformed front wheel suspension or abnormal wheel alignment; 7. Stuck steering column. The steering wheel is connected to the steering shaft via splines, converting the driver's force applied to the wheel's edge into torque transmitted to the steering shaft. Methods to lighten car steering: 1. Start the engine and engage gear, wait 3 seconds; 2. Turn steering wheel fully left/right, wait 3 seconds, then return to center and turn off engine.

2

4

Share

Is the Outlander domestically produced?

Outlander is domestically produced. The Outlander is a compact 5-door, 5-seat SUV with body dimensions of 4705mm in length, 1810mm in width, and 1710mm in height, a wheelbase of 2670mm, a fuel tank capacity of 63 liters, and tire specifications of 225/55R18. The Outlander is equipped with a 2.0L naturally aspirated engine and a CVT continuously variable transmission, delivering a maximum power of 122 kW at 6000 rpm and a maximum torque of 201 Nm at 4200 rpm. It features front-wheel drive, with MacPherson independent suspension at the front and multi-link independent suspension at the rear.

4

1

Share

Is Jetta a joint venture brand or an independent brand?

What Causes a Car Navigation Screen to Go Black?

What is the method for removing car window film?

What is the function of the P gear in an automatic transmission car?

How to Adjust the Rearview Mirrors of a Citroën Sedan?

What Causes Heavy Steering Wheel in Cars?

Is the Outlander domestically produced?

How to turn on the fog lights on the Lavida Plus?

How to Use the Santana Windshield Wiper?

What does the car display when it runs out of engine oil?

How are the grades of engine oil classified?