Is it worth calling the police for a deep scratch on the car?

What is the maximum wading depth of the Wrangler?

According to official information, the maximum wading depth of the Wrangler is 85 cm. Common tire specifications are 255/70R18 and 245/75R17, with body lengths of 4882mm and 4334mm, and a vehicle weight ranging from 1843kg to 2049kg. The body structure is available as a 4-door 5-seat SUV and a 2-door 4-seat SUV. The maximum wading depth refers to the deepest water a vehicle can safely pass through. Generally, the maximum wading depth for sedans does not exceed 30 cm, while SUVs have a higher maximum wading depth, but it is still best not to exceed 50 cm. Among common models, the GAC Trumpchi GS8 has a maximum wading depth of 30 cm, the Audi A4 has 32 cm, the Volkswagen Sagitar has 30 cm, the Land Rover Range Rover has 90 cm, the Jeep Compass has 48 cm, and the Highlander has 45 cm. The maximum wading depth of SUVs is significantly higher than that of sedans. Generally, when driving through water, vehicle owners should take different measures depending on the depth of the water and the vehicle's characteristics, as follows: If the wading depth reaches the height of the exhaust pipe, it is relatively safe. Even if water enters the exhaust pipe, the pressure inside is sufficient to expel the water. As long as the engine is not turned off in the water, water will not flow back into the vehicle. If the wading depth reaches the height of the door frame, it becomes more dangerous. The vehicle's circuits, electronic components, and sensors are mostly concentrated at the bottom of the car, which could lead to circuit failures, damaging critical electrical components and preventing the car from starting normally. If the wading depth reaches the height of the intake pipe, it is extremely dangerous. Driving directly into such a section could cause the vehicle to stall immediately, leading to permanent engine damage or rendering the engine unusable.

9

0

Share

How to Start the Engine When the Baojun 530 Has No Power?

Methods to start a Baojun 530 when the battery is dead: 1. Push-start method: First, turn the key to the ignition position, press the clutch, release the handbrake, and set the gear to 1st or 2nd. Keep the clutch pressed and start pushing the car. When the speed reaches 5 km/h, slowly release the clutch and press the accelerator to start the engine. 2. Jump-start method: Open the hoods of both cars. Connect the negative terminal of the jumper cable to the negative terminal of the dead battery and the other end to the negative terminal of the donor car's battery. Similarly, connect the positive terminal of the jumper cable to the positive terminal of the dead battery and the other end to the positive terminal of the donor car's battery. Then, start the donor car and rev the engine slightly. Try starting the dead car. 3. Towing-start method: Use a sturdy tow rope to securely tie the front and rear of both cars together. Begin towing slowly, ensuring both cars maintain a steady speed and paying attention to safety. Once the towed car starts, notify the towing car immediately and slowly pull over to the side of the road to stop.

16

4

Share

What is the Difference Between Hybrid Electric and Plug-in Hybrid Vehicles?

Here is an introduction to the differences between the two: 1. Power difference. Plug-in hybrids are usually designed with the main goal of enhancing vehicle performance, such as the Ferrari SF90, Porsche Cayenne, Panamera Plug-in Hybrid, and BYD Dynasty series. In this regard, Chinese brands have performed exceptionally well. For example, BYD's DM models have nearly double the power compared to their fuel-powered counterparts. Of course, some are aimed at improving smoothness, such as BMW plug-in hybrids, Volkswagen plug-in hybrids, and Geely. Others focus on energy efficiency, such as Korean brands and SAIC-GM plug-in hybrids. 2. Driving experience. Plug-in hybrids are typically equipped with large batteries, enabling pure electric driving for 50-100 kilometers. If battery costs decrease, this range may increase in the future. Hybrid electric vehicles, on the other hand, only come with small batteries and can hardly drive purely on electricity. Although they have an EV mode, the engine needs to start and assist in charging after just 1-2 kilometers of pure electric driving. 3. Driving environment. Hybrid electric vehicles save fuel mainly in urban areas; on highways, their fuel consumption is almost the same as that of conventional fuel vehicles, and sometimes even higher. Examples include Toyota's dual-engine models.

19

4

Share

Is a Fuel Consumption of 9-10L Normal for the Mistra?

A fuel consumption of 9-10L for the Mistra is considered normal. In actual driving conditions, factors such as inadequate driving skills, poor engine condition, and lack of maintenance can lead to increased fuel consumption. The combined fuel consumption of the Mistra is 5.3L/100km. There are currently 5 models of the Mistra available for sale: the DCT-LUX Premium Edition, DCT-TOP Flagship Edition, CVT-GLS Leading Edition, CVT-GLX Elite Edition, and CVT-LUX Premium Edition, all with a combined fuel consumption of 5.3L/100km. The above figures are based on the NEDC combined fuel consumption, which measures the fuel consumption data under the NEDC test cycle. The actual fuel consumption is higher, ranging from 6.0-11.0L/100km. Methods to reduce fuel consumption: Clean engine carbon deposits: Excessive carbon deposits in the engine are a significant cause, often due to using unsuitable fuel. It is recommended to add a certain amount of cleaning agent when refueling. If the effect is not noticeable, it indicates a high level of carbon deposits in the engine. In such cases, the car should be taken to a 4S shop for professional cleaning of the engine carbon deposits by technicians. Check the oxygen sensor: As an internal control unit of the car, the oxygen sensor monitors the air-fuel ratio in the engine. If it is damaged, it can cause an imbalance in the air-fuel ratio, leading to a sudden increase in fuel consumption. When the oxygen sensor is damaged, the exhaust pipe emits darker-colored exhaust gases during driving, and the sensor should be replaced immediately. Regularly replace the three filters: During vehicle use, the oil filter, air filter, and fuel filter must be replaced regularly. If not replaced for a long time, they can become dirty and send incorrect information to the engine control unit, resulting in incomplete fuel combustion and increased engine carbon deposits. Check the electronic control unit: Although the engine's electronic control unit is highly reliable, in older vehicles, various faults may occur.

15

0

Share

What is the function of a CAN controller?

CAN controller is responsible for receiving data sent by the microprocessor in the control unit, processing the data and transmitting it to the CAN transceiver. At the same time, the CAN controller also receives the data from the CAN transceiver, processes the data and transmits it to the microprocessor. Here are some relevant information: 1. The automotive CAN controller is manufactured on a programmable chip through the combination of logic circuits. This controller has an interface for connecting with single-chip microprocessors, and can be programmed by the microprocessor to set its working mode, control its working state, and perform data transmission or reception. 2. Automotive CAN controllers usually come in two types, both strictly complying with CAN specifications and international standards. Their characteristics are as follows: (1) Independent automotive CAN controller This type of CAN controller has relative independence and is very flexible to use. It generally appears in the form of a single-chip integrated circuit and can be combined with various types of single-chip microprocessors. (2) Combined automotive CAN controller This CAN controller is integrated with the microprocessor to form a microprocessor control component with a CAN control function interface. Using a combined CAN controller can simplify and compact the circuit, and the efficiency can also be improved accordingly.

11

0

Share

Can 5w30 engine oil be used in summer?

Engine oil 5W30 can be used in summer. Here is the relevant introduction about engine oil: 1. The engine oil grade usually indicates viscosity and quality. 2. The viscosity of lubricating oil is mostly identified by SAE grade, and SAE is the abbreviation of "Society of Automotive Engineers" in English. 3. W stands for winter, and the smaller the number in front of it, the better the low-temperature fluidity of the engine oil, representing the lower ambient temperature available and the better protection ability for the engine during cold starts. 3. The number after "W" (after a horizontal line) is an indicator of the oil's high-temperature resistance. The larger the number, the better the protection performance of the oil at high temperatures. 4. The grade after the oil classification indicates its viscosity specification. For example, in "15W-40, 5W-40", "W" stands for Winter, and the smaller the number in front of it, the better the low-temperature fluidity of the engine oil, representing the lower ambient temperature available and the better protection ability for the engine during cold starts. For example, 5W represents resistance to external low temperatures of -30°C, while 20W is resistant to low temperatures of -15°C.

15

2

Share

Is it worth calling the police for a deep scratch on the car?

What is the maximum wading depth of the Wrangler?

How to Start the Engine When the Baojun 530 Has No Power?

What is the Difference Between Hybrid Electric and Plug-in Hybrid Vehicles?

Is a Fuel Consumption of 9-10L Normal for the Mistra?

What is the function of a CAN controller?

Can 5w30 engine oil be used in summer?

Where is the battery located in an Audi TT?

What kind of oil should be added to the transmission?

How to Add Antifreeze to BYD Song?

Where does brake fluid leak from?