Is it serious if the driver's license expires for three months?

1 Answers
HoldenRose
07/29/25 5:01pm
It is serious. Even one day overdue counts as expired. An expired driver's license cannot be used to drive motor vehicles on the road, which constitutes unlicensed driving. If caught by traffic police, the vehicle will be impounded immediately. Below is additional information: 1. Regarding the renewal period for an expiring driver's license: The first issued driver's license is valid for six years, and renewal must be completed within three months before the expiration date. A driver's license that has exceeded its validity period cannot be used to drive. In most cities, the renewal can be completed on the same day, and there are self-service renewal machines at the vehicle management office for convenient processing. However, if the license has already expired, renewal can only be done at the service hall of the vehicle management office. 2. Regarding delayed renewal of the driver's license: Due to special circumstances or reasons, some people may not be able to renew their license within a short period. For example, if someone is abroad, in another city, or on a long business trip without their driver's license, and the license is about to expire, they can apply for a delayed renewal. Once the delayed renewal is approved, the driver's license will be temporarily frozen, meaning driving is not allowed. Only after completing the renewal procedures at the vehicle management office can the individual continue to drive. The maximum delay period for a driver's license renewal is three years.
Was this review help?
1
2
Share
More Forum Discussions

How to Replace the Battery in a Xpeng G3 Key Fob?

Use a flathead screwdriver to pry open the key fob cover at the groove position of the Xpeng G3 key. After prying open the key fob cover, remove the internal circuit chip of the Xpeng car key. Once the internal circuit chip of the Xpeng car key is removed, take out the battery inside the key. Finally, reverse the steps to install the new battery and complete the battery replacement. When installing the key battery, ensure the positive side faces upward; otherwise, incorrect installation may render the key unusable.
5
2
Share

How to Alert the Rear Vehicle for Overtaking?

Before overtaking, first check the left rearview mirror to ensure safety. After confirming safety, turn on the lights and flash the high and low beams alternately twice to signal the rear vehicle for overtaking. Slow down your vehicle and move to the right to assist the rear vehicle in overtaking. Flash the headlights once to signal the slow-moving vehicle ahead to yield, facilitating your overtaking. If the other vehicle flashes back once, it indicates their agreement to change lanes or allow overtaking. Alert the other vehicle that your car is malfunctioning and may brake suddenly, informing them to maintain a safe distance.
7
3
Share

How to Change the Transmission Oil for Mercedes-Benz GL350

Transmission oil replacement requires lifting the vehicle with a car lift. Remove the drain plug on the side of the oil pan. After draining, use a specialized tool to poke the oil hole, which can release a bit more oil. Take off the oil pan, clean it thoroughly, replace the filter and sealing ring, then reinstall it. When adding new oil, there are two entry points: one is the oil filler port next to the oil dipstick, and the other is directly pumping the transmission oil through the drain hole on the oil pan. Transmission oil is a lubricant that keeps the gear system clean, ensuring smooth operation of the transmission and extending the lifespan of the drivetrain components.
1
0
Share

How to Remove the Door Handle of a Besturn B50?

Insert a small flathead screwdriver into the small square hole and gently pry it open to remove the lock cylinder decorative cover. Open the car door and locate a rubber pad on the door edge. Use a small flathead screwdriver to pry off the rubber pad, then remove the door handle lock block screw. Take out the small flathead screwdriver and use it to pry off the small round cover at the door handle's fixed screw position. Use the small flathead screwdriver to pry the door handle lock block from the gap between the lock block and the door panel, then disassemble the door handle lock block. Hold the door handle with your left hand and pull it backward to separate the door handle from the door panel.
10
3
Share

How to Add Windshield Washer Fluid to MG6?

Locate the filler port. The windshield washer fluid filler port is located on the left side of the engine compartment, near the edge. After locating the filler port, open the filler cap. Pour in the windshield washer fluid. Be careful not to overfill, as excess fluid may spill out and cause unnecessary waste. The washer fluid reservoir has a capacity of 3 liters. High-quality windshield washer fluid has properties such as non-stickiness, anti-static, anti-corrosion, dust-proof, cold resistance, acid rain resistance, anti-freeze, and UV protection.
14
3
Share

How to Remove the Airbag in Chery Ant?

Turn off the ignition key. If you proceed with removal without turning it off, accidental deployment may occur, or error codes might be generated, causing the ECU to malfunction. There are two bolts on the back cover of the steering wheel. Remove the bolts and gently lift the cover. Then, take off the steering wheel. Disconnect the clock spring connector attached to the inflator. Typically, the connector has a locking mechanism—some require pressing to release, while others need to be pulled out. Unclip the yellow safety latch behind the airbag, then pull out the airbag connector to remove the airbag.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.