Is It Serious If I Didn't Get the Green Book When Buying a Car?

2 Answers
IkerFitz
08/30/25 7:12am
Not getting the green book when buying a car is very serious, because the vehicle's green book is as important as a person's ID card and is required at all times. Here is relevant information about the vehicle registration certificate: 1. Function: The vehicle registration certificate is not the legal proof of vehicle ownership, but rather an administrative document permitting the vehicle to be driven on the road. 2. Importance: The motor vehicle registration certificate is a necessary property ownership document for the vehicle, kept by the vehicle owner and not carried with the vehicle. It is required to be presented for any vehicle registration procedures such as transfer of registration and change of ownership, and records relevant information about the vehicle, equivalent to the vehicle's household registration booklet.
Was this review help?
4
2
Share
SanWalter
09/12/25 4:10am
I think not getting the green book when buying a car is quite a serious issue, and you need to take it seriously immediately. The green book is that small green booklet, officially called the Vehicle Registration Certificate, which proves that the car is yours, with ownership clearly recorded on it. Without it, first of all, transferring ownership becomes a huge hassle—both the seller and buyer must be present for verification, otherwise, the DMV won’t process it, and the car you bought becomes an 'illegal vehicle.' Secondly, you won’t pass the annual inspection, and in case of an accident or insurance claim, the insurer might deny your claim because you can’t provide legal proof. There are also legal risks, such as having no evidence if the car gets stolen or losing out in disputes during transactions. I experienced a similar situation when I bought a car—luckily, I contacted the seller in time to get it sorted, or it would have caused a lot of delays. My advice is to contact the DMV immediately if you find out you don’t have the green book. It might be that the seller forgot to give it to you or the paperwork wasn’t completed properly. Resolving it early can prevent bigger troubles.
Was this review help?
17
0
Share
Expand All
More Forum Discussions

How to Reset the Grand Cherokee On-Board Computer?

The steps to reset the Grand Cherokee on-board computer are as follows: 1. Disconnect the positive terminal of the battery. Note: Ensure the engine is turned off and all electrical devices are switched off before disconnecting the battery. 2. Reconnect the battery. 3. Power on the vehicle and wait for the computer to self-check for 30 seconds. 4. Power off the vehicle and wait for another 30 seconds. 5. Start the engine. More details are as follows: 1. The vehicle's computer, also known as the on-board computer (ECU), or electronic control unit, processes simple electronic signals and performs basic calculations using simple logic gates and integrated circuit principles. 2. It receives data from various sensors throughout the vehicle, processes and computes this information, and then sends signals to the engine to control its operation (such as the fuel injection system and ignition timing).
10
3
Share

Why does the car jerk when hot but not when cold?

Cold car does not jerk but hot car jerks because the solenoid valve is damaged and needs to be repaired at a professional repair shop in time. The following is a related introduction about the solenoid valve: Introduction: The solenoid valve (Electromagnetic-valve) is an industrial equipment controlled by electromagnetics, which is an automated basic component used to control fluids and belongs to the actuator, not limited to hydraulics and pneumatics. It is used in industrial control systems to adjust the direction, flow, speed and other parameters of the medium. The solenoid valve can cooperate with different circuits to achieve the expected control, and the control accuracy and flexibility can be guaranteed. There are many types of solenoid valves, and different solenoid valves play a role in different positions of the control system. The most commonly used are check valves, safety valves, directional control valves, speed regulating valves, etc. Working principle: There is a sealed cavity in the solenoid valve, with through holes opened in different positions. Each hole is connected to a different oil pipe. The middle of the cavity is a piston, and both sides are two electromagnets. The valve body will be attracted to the side where the magnetic coil is energized. By controlling the movement of the valve body, different oil discharge holes are opened or closed, while the oil inlet hole is always open. The hydraulic oil will enter different oil discharge pipes, and then the pressure of the oil pushes the piston of the oil cylinder. The piston drives the piston rod, and the piston rod drives the mechanical device. In this way, the mechanical movement is controlled by controlling the current on and off of the electromagnet.
17
4
Share

How Often Should a Passenger Car Undergo Inspection?

For new vehicles within 6 years, an inspection is required every two years. Vehicles older than 6 years must be inspected annually, while those exceeding 15 years require inspection every 6 months. The inspection standards for other vehicle types are as follows: 1. Operational passenger vehicles must be inspected annually within the first 5 years and every 6 months thereafter. 2. Trucks, as well as large and medium-sized non-operational passenger vehicles, require annual inspection within the first 10 years and every 6 months thereafter. 3. Small and mini non-operational passenger vehicles must be inspected every 2 years within the first 6 years, annually thereafter, and every 6 months after 15 years. 4. Motorcycles must be inspected every 2 years within the first 4 years and annually thereafter. 5. Tractors and other motor vehicles require annual inspection.
17
5
Share

What Causes the Abnormal Noise in Car Windows?

There could be several reasons for abnormal noise in car windows: 1. The noise during window glass movement may be due to dust accumulation in the rubber guide channels, increasing resistance and causing squeaking sounds. The solution is to clean the glass guide channels. 2. Aging rubber in the window glass guide channels can lead to slight jamming and noise during window movement, which can be resolved by applying lubricant. 3. If the window glass not only makes noise but also moves with difficulty, tilts to one side, or fails to respond during operation, it might be due to lost initialization data of the window. Performing a reinitialization of the window can solve this issue.
5
3
Share

How to Check What Year a Car Model Is?

Here are the methods to check what year a car model is: 1. The most direct method is to refer to the instruction manual provided at the time of purchase, which contains detailed information. You can also make a phone inquiry; there is always a dedicated customer service representative assigned when you buy a car, whom you can consult directly if you have any questions, including those about the car. 2. Another method is to check the car's VIN code. The 10th digit of the VIN code indicates the year, though this year may slightly differ from the manufacturing year, usually by no more than a year, and is generally close to the model year, often considered the default. Additionally, you can take a picture of the car and use Baidu's image recognition feature to identify it. Once identified, detailed information, including the year, will be available.
14
0
Share

Why is the steering wheel not straight after changing tires?

Here are the specific reasons why the steering wheel is not straight after changing tires: 1. Inconsistent tire pressure: If the tire pressure on the left and right sides is uneven, it can cause the steering wheel to pull to one side while driving. 2. Abnormal wear: Issues like uneven tire wear can lead to steering wheel misalignment, and may even cause slight steering wheel vibration at high speeds. In such cases, a wheel alignment adjustment is necessary. 3. Suspension system failure: Manufacturers conduct strict inspections and adjustments on vehicles before leaving the factory. For example, interference between the suspension guide rods and the steering linkage can affect vehicle alignment.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.