Is it safe to install a one-button start system for the Excelle at a 4S dealership?

1 Answers
OAlexander
07/29/25 9:17pm
Installing a one-button start system for the Excelle at a 4S dealership is not safe and poses certain security risks. The reason is that modifying the one-button start system may damage the original vehicle wiring, leading to the malfunction of some vehicle functions. Functions of the one-button start system: 1. Automatic unlocking; 2. Automatic locking; 3. Automatic window closing; 4. Automatic anti-theft; 5. One-button start; 6. One-button shutdown. The method to use the one-button start system: 1. Open the car door and sit inside; 2. Press the brake pedal; 3. Press the start button to complete the one-button start. The working principle of the one-button start system: It uses radio frequency identification technology, automatically unlocking the door through the chip in the smart card. When the owner approaches the vehicle, the car automatically recognizes the owner's identity, and the door locks will open automatically while disabling the anti-theft system, eliminating the need for a key.
Was this review help?
19
3
Share
More Forum Discussions

How to Measure Engine Oil Pressure?

Measuring engine oil pressure involves the following steps: 1. Disconnect the wiring harness plug of the oil pressure sensor and remove the oil pressure sensor; 2. Screw the hose connector of the oil pressure gauge into the threaded hole where the oil pressure sensor was installed and tighten the connector; 3. Place the oil pressure gauge in a location where it will not come into contact with rotating or high-temperature engine components; 4. Start the engine and check for oil leaks at the oil pressure gauge connector. If there is a leak, turn off the engine and retighten the connector; 5. Run the engine until it reaches normal operating temperature, then check the oil pressure gauge readings at idle and at 2000 RPM, comparing them with the standard pressure values; 6. The standard oil pressure for different engine models varies, but it should generally be greater than 0.05 MPa at idle and greater than 0.2 MPa at 2000 RPM; 7. After measuring the oil pressure, remove the oil pressure gauge, install the oil pressure sensor, tighten it to the specified torque, reconnect the wiring harness plug, and start the engine to confirm there are no oil leaks from the oil pressure sensor.
17
3
Share

How to Turn On the Rearview Mirror Heating in the 2021 Sagitar?

Entering the driver's cabin, you can see the rearview mirror heating button located on the left side of the center console. By default, the rearview mirror heating is turned off, and the indicator light above it is off. Press the rearview mirror heating button to turn it on. The indicator light above will illuminate, indicating that the rearview mirror is currently in the heating state.
3
0
Share

How to Display the Tire Pressure Gauge?

Car tire pressure display can be viewed by pressing the SET button on the dashboard. The car's tire pressure monitoring is automatic; if there is an issue with tire pressure, the onboard computer will alert you. Regularly checking the tires is sufficient. The tire pressure monitoring system is a type of active safety device. It can promptly alert the driver when there are signs of danger in the tires, prompting them to take appropriate measures, thereby preventing serious accidents. With a tire pressure monitoring system, you can ensure the tires always operate within the specified pressure and temperature range, reducing tire damage and extending their lifespan. 1. Inflate all four tires to the proper pressure. 2. Press and hold the tire pressure monitoring key (to set the system to the stable state tire pressure). 3. The system will then alert you when the tire pressure is insufficient. Repeat the above two steps as needed. Note: Hold the SET button for 3 seconds to set the current tire pressure as the standard value. If the tire pressure in any wheel is incorrect, the tire pressure light will illuminate. Regarding checking the tire pressure monitoring: The tire pressure monitoring does not display when the tire pressure is normal; it only shows when the pressure is abnormal, such as when there is insufficient air.
1
4
Share

Correct Method for Starting a Sagitar Automatic Transmission Car

Turn the ignition key to the second position, the power-on position, allowing the car's computer system to begin self-checking for at least 6 seconds or more. Press the foot brake and shift the gear from P (Park) to N (Neutral). Release the foot brake and turn the ignition key to the start position to fire up the engine. Press the foot brake, release the handbrake, and shift the gear from N (Neutral) to D (Drive). Slowly release the foot brake to start moving.
19
5
Share

What to Do When a Scooter Motorcycle Won't Start Due to Water Ingress?

Check if the air filter, carburetor, and exhaust pipe have water ingress. Clean the air filter and carburetor, replace the engine oil, and ensure all water is drained before starting. It might be that the ignition system components like the high-voltage cap, ignition coil, or igniter got wet. In this case, no repair is needed—just let the vehicle dry thoroughly before starting.
2
5
Share

What to Do in an Emergency When a Scooter Runs Out of Fuel?

Keep the electric starter engaged for a while. Turn off the key, use the kick starter with the throttle fully open, and pump to draw fuel into the carburetor. Locate the suction tube of the fuel tank switch, pull it off, and suck on it for a while. Fuel will flow directly into the carburetor, allowing normal ignition.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.