Is It Reasonable for Driving Schools to Charge Additional Training Fees for Retests?

What kind of driver's license is required for a concrete mixer truck?

To operate a concrete mixer truck, a B2 license is required, along with a general cargo transport qualification certificate. The permitted vehicle types and corresponding license codes are as follows: 1. Large bus A1 license allows driving large passenger vehicles and A3, B1, B2, C1, C2, C3, C4, M; 2. Tractor A2 license allows driving heavy and medium-sized full trailers, semi-trailer combinations and B1, B2, C1, C2, C3, C4, M; 3. City bus A3 license allows driving city buses with a capacity of 10 or more passengers and C1, C2, C3, C4; 4. Medium bus B1 license allows driving medium-sized passenger vehicles (including city buses with a capacity of 10 to 19 passengers) and C1, C2, C3, C4, M; 5. Large truck B2 license allows driving heavy and medium-sized trucks; large, heavy, and medium-sized special-purpose vehicles and C1, C2, C3, C4, M; 6. Small car C1 license allows driving manual or automatic transmission vehicles with 9 or fewer seats, including small and mini passenger vehicles, light and mini cargo vehicles, light, small, and mini special-purpose vehicles, small automatic transmission cars C2, low-speed cargo vehicles C3, and three-wheeled vehicles C4; 7. Small automatic transmission car C2 license allows driving small and mini automatic transmission passenger vehicles and light and mini automatic transmission cargo vehicles.

1

2

Share

Is the Audi Q7 a pure import?

Audi Q7 is a pure import and a mid-to-large-sized SUV. Taking the 2012 Audi Q7 as an example, its body dimensions are: length 5067mm, width 1970mm, height 1731mm, wheelbase 2996mm, fuel tank capacity 85l, and curb weight 2115kg. The 2012 Audi Q7 is equipped with a 2.0T turbocharged engine, with a maximum power of 180kW and a maximum torque of 370Nm, paired with an 8-speed automatic manual transmission. It adopts a front-engine four-wheel-drive layout, and both front and rear suspensions use multi-link independent suspension.

13

0

Share

How to Check the Engine Oil Level in a Lynk & Co 01?

The method to check the engine oil level in a Lynk & Co 01 is: 1. The oil dipstick of the Lynk & Co 01 is located on the dashboard. Without pressing the brake pedal, hold down the start button for ten seconds, and the oil condition will be displayed on the dashboard; 2. When checking, ensure that all four wheels of the car are parked at the same horizontal level, and the body should not be tilted. If the body is tilted, the oil level in the oil pan will change, resulting in inaccurate measurements. Taking the 2020 Lynk & Co 01 as an example, it belongs to the compact SUV category, with body dimensions of: length 4512mm, width 1857mm, height 1689mm, a wheelbase of 2734mm, and a curb weight of 1736kg.

11

4

Share

What is the Maybach S500?

Maybach S refers to the Maybach S-Class sedan, but the Maybach S-Class sedan only comes in S450, S560, and S680 models. Below are the specific details of the Maybach S-Class sedan: 1. S450: Equipped with a 3.0-liter twin-turbocharged engine, the 3.0-liter twin-turbocharged engine has a maximum power output of 270 kW, maximum torque of 500 Nm, maximum power speed of 5500 rpm, and maximum torque speed ranging from 1800 to 4500 rpm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a 9-speed automatic transmission. 2. S560: Equipped with a 4.0-liter twin-turbocharged engine, the 4.0-liter twin-turbocharged engine has a maximum power output of 345 kW, maximum torque of 700 Nm, maximum power speed of 5250 rpm, and maximum torque speed ranging from 2000 to 4000 rpm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a 9-speed automatic transmission. 3. S680: Equipped with a 6.0-liter twin-turbocharged engine, the 6.0-liter twin-turbocharged engine has a maximum power output of 463 kW, maximum torque of 1000 Nm, maximum power speed of 4800 rpm, and maximum torque speed ranging from 2300 to 4200 rpm. This engine features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a 7-speed automatic transmission.

19

0

Share

How long does it take to get the car back after a full-body paint job?

Different 4S shops have varying paint job durations, typically around one week to get the car back. Below are methods for maintaining car paint: 1. Apply a paint protection film (PPF): PPF effectively protects the vehicle's paint, causing no harm to the original paint while ensuring the paint's glossiness. It's currently a highly recommended method. 2. Characteristics of PPF: PPF is applied in separate sections. Each section is independently applied, allowing for direct replacement if damaged without affecting other sections of the film.

8

2

Share

What Causes Abnormal Noise During Engine Idling?

Engine idle abnormal noise may be caused by the following reasons: Timing chain elongation, tensioner pressure loss, balance shaft wear: Timing chain elongation is generally caused by metal fatigue. After prolonged driving combined with the high-temperature working environment of the timing chain, elongation can easily occur, leading to abnormal noise. The tensioner is connected to the oil passage and adjusts the tightness of the timing chain through oil pressure. If the tensioner oil passage is blocked or the internal check valve loses pressure, the chain may loosen and produce noise. The balance shaft is used to reduce vibrations generated during engine operation. If the balance shaft oil passage is blocked, it can increase wear on the journal and bearings, resulting in noise. Camshaft, crankshaft, and connecting rod bearing wear: If the vehicle uses low-quality oil, excessive sludge may form in the engine, blocking the lubrication oil passages and preventing oil from reaching components that require lubrication and cooling. This can cause wear on the camshaft, crankshaft, and connecting rod bearings, leading to noise. Additionally, if the engine lacks coolant, causing excessive engine temperature, the above phenomena may also occur. In severe cases, it can even lead to cylinder scuffing or bearing seizure. Increased timing variable wheel clearance: Variable valve timing can adjust according to engine speed and operating conditions, typically using hydraulic control to advance or delay the camshaft timing gear's internal rotor by a certain angle. If the variable timing wheel's internal rotor is stuck or the oil cavity is worn, the clearance may increase, causing noise. Excessive valve clearance or damaged rocker arm: The rocker arm is a lever mechanism that presses the valve, and the valve clearance is mainly controlled by the hydraulic lifter. Damage to either can result in valve noise.

6

5

Share

Is It Reasonable for Driving Schools to Charge Additional Training Fees for Retests?

What kind of driver's license is required for a concrete mixer truck?

Is the Audi Q7 a pure import?

How to Check the Engine Oil Level in a Lynk & Co 01?

What is the Maybach S500?

How long does it take to get the car back after a full-body paint job?

What Causes Abnormal Noise During Engine Idling?

What causes the idle vibration of the Trumpchi GS4?

Does a brake pad thickness of 4mm require replacement?

What is the correct way to depress the clutch when driving?

What is the body length of the Changan CS75?