Is it okay to store a battery at home without charging it?

1 Answers
DeJulian
07/30/25 6:16am
Storing a battery at home without charging it is okay. How a battery works: A battery, also known as a storage battery, is a type of cell that converts chemical energy into electrical energy. Typically, the term 'battery' refers to a lead-acid battery, which is mainly made of lead and its oxides, with a sulfuric acid solution as the electrolyte. Battery maintenance methods: Avoid storing the battery in a discharged state. A discharged state means the battery was not recharged promptly after use, which can lead to sulfation—a process where lead sulfate crystals form on the plates, blocking ion channels and resulting in insufficient charging and reduced battery capacity. The longer a battery remains idle in a discharged state, the more severe the damage. When a battery is not in use, it should be charged once a month to extend its lifespan.
Was this review help?
9
2
Share
More Forum Discussions

What are the reasons why a moped won't start?

The reasons why a moped won't start include: 1. The moped's battery is low on power, causing it not to start. 2. The moped's starter motor is broken, making it impossible to start. 3. The moped has run out of fuel, causing it not to start, etc. When encountering the above issues, you can go to a moped repair shop to specifically check what the problem is. If you need to diagnose the root cause yourself, the operation methods are as follows: 1. Check if the starter motor is turning. If it's not turning, inspect whether the starter motor's circuit is open. 2. If the starter motor is turning but the moped won't start, it might be an engine issue. Check the seal between the cylinder block and cylinder head, the tightness of the valves, the wear of the piston rings or cylinder block, etc. 3. Check if the negative pressure rubber tube connected to the throttle is aged, cracked, or leaking, if the three-way fuel tank switch is damaged, if the carburetor fuel filter is clogged, if the fuel line is clear, or if the vacuum diaphragm is ruptured. 4. Also, check if the air filter is clogged or try removing the air filter and attempt to start the moped again.
13
2
Share

What to Do When the Car Interior Gets Wet?

After the seats get wet, use a damp towel along with a neutral or alkaline cleaning product to gently wipe the surface of the seats, removing any stains. After cleaning, use a softer towel to dry the surface moisture, then allow the seats to air dry naturally. During the drying process, avoid using a hairdryer or exposing them to direct sunlight, as this can damage the leather.
20
4
Share

What to Do If You Have Poor Car Control and Can't Tell If the Car Body Is Straight or Not?

Steer straight by keeping the steering wheel level and stationary, but first make sure the steering wheel is properly aligned. If the car drifts to one side, slightly turn the steering wheel in the opposite direction. After understanding the key points for keeping the car straight with the steering wheel, the next step is to learn to find suitable reference points on the road. It's been observed that many beginners tend to drift off course when driving on wide roads. The reason is the excessive space and broad field of vision.
11
4
Share

What to Do When the Rear Wheel Falls into a Ditch?

If the car is stuck in such a ditch, you can use the jack from the trunk and find a thick, flat wooden board nearby to place under the wheel in the ditch, then slowly drive out. This is the safest and most professional approach, regardless of the ditch's depth. It is also quite convenient. Moreover, it allows you to move the car out without damaging the chassis. This situation usually occurs when the car is stuck in a relatively deep ditch. For safety and to minimize damage, it is best to take this measure.
11
3
Share

What are the methods and steps for rubbing the vehicle frame number?

First, clean and dry the area where the vehicle frame number is located, then evenly apply red ink paste onto the frame number. Stick a transparent adhesive tape over the frame number. Next, crumple a relatively new piece of carbon paper into a ball and rub it back and forth over the flat surface of the engine number. Place a thin sheet of white paper over the engine number and frame number, then gently rub horizontally with a pencil to create the desired number imprint.
2
1
Share

How to Turn On the Rear Air Conditioning in a Car?

After starting the car, wait for 8-15 minutes until the water temperature rises to the normal level, then turn on the air conditioning. Adjust the air conditioning circulation mode to the internal circulation setting. AUTO automatic operation mode: Press the AUTO button to activate the air conditioning, which will then automatically adjust the interior temperature. A/C manual operation mode: Press the A/C button to enter the temperature setting mode, where you need to manually set the desired temperature and select the airflow direction.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.