Is it normal to have small water droplets inside new headlights?

1 Answers
NadiaLee
07/28/25 2:58pm
It is normal to have small water droplets inside new headlights. Rubber vent tube: In all current vehicle models, whether they are halogen headlights, xenon headlights, or the more technologically advanced LED headlights, there is a rubber vent tube behind these lights. When the headlights are instantly ignited or during normal driving, the heat generated is expelled through this tube. However, precisely because of the existence of this tube, moisture from the air can "seize the opportunity" to enter the interior of the headlights. Over time, this moisture forms fog, which accumulates into small water droplets. Headlight fogging: Headlight fogging generally occurs more easily in southern regions, during winter, or in months with more rainfall. In winter, the temperature difference between the inside and outside of the headlights is too high, similar to the principle of fog forming on glasses when moving from a cold outdoor environment to a warm indoor one. Solution for fogging: Headlight fogging is a normal phenomenon and can only dissipate slowly through the headlight's own heat. The best approach is to avoid using methods that could damage the headlights, such as hair dryers, heat guns, or high-pressure water jets, as these can harm the headlights.
Was this review help?
8
1
Share
More Forum Discussions

Where is the reverse gear position in a manual transmission?

Manual transmission reverse gear position is the R gear. On the shift lever of manual transmission cars, there are markings. The reverse gear in automatic transmission cars is also the R gear. After shifting into R gear, the reverse gear will engage, allowing the car to move backward. Most manual transmission cars do not have a synchronizer for the reverse gear. The correct method to start a manual transmission car is: 1. Fully depress the clutch; 2. Shift into 1st gear; 3. Turn on the left turn signal; 4. Honk the horn as a reminder; 5. Release the handbrake; 6. Gently lift the clutch with the left foot; 7. The vehicle starts moving, keep the clutch steady with the left foot, avoid pressing down or lifting to prevent stalling; 8. After holding steady for 3 seconds, slowly release the clutch while gently pressing the accelerator with the right foot, then slowly release the accelerator, fully depress the clutch to shift into 2nd gear, and repeat this process to shift into 3rd gear, completing a smooth start.
18
5
Share

What are the precautions for driving on slopes?

Precautions for driving on slopes include: 1. Maintain your lane while driving and avoid swaying or crossing the road centerline; 2. Shift to a lower gear when descending steep or long slopes; 3. Do not coast in neutral or with the engine off when going downhill; 4. When going uphill, be aware of blind spots on the slope and avoid overtaking; 5. In case of prolonged traffic congestion on a slope, do not constantly press the brake—instead, engage the handbrake firmly to prevent rolling back; 6. Utilize engine braking to reduce the vehicle's coasting speed when descending; 7. Avoid shifting gears while on an uphill slope whenever possible; 8. If gear shifting is necessary, adjust the gear before starting the ascent; 9. Control the vehicle's speed when descending and prepare to reduce speed in advance; 10. Use engine braking to manage speed, applying intermittent braking (pump the brakes) rather than prolonged or emergency braking.
18
5
Share

What are the body dimensions of the Buick Enclave?

Buick Enclave's body dimensions are: length 4981mm, width 1953mm, height 1727mm, wheelbase 2863mm, fuel tank capacity 73L, minimum ground clearance 180mm, trunk volume 222L, curb weight 1880kg. The Buick Enclave features MacPherson strut front suspension and five-link independent rear suspension. It is equipped with a 2.0T turbocharged engine delivering maximum horsepower of 237PS, maximum power of 174kW, and maximum torque of 350Nm, paired with a 9-speed automatic transmission.
8
0
Share

What to Do If a BMW Wheel Hub Gets Scratched?

The solutions for a scratched BMW wheel hub are: 1. Clean the wheel hub: Check all scratches, the depth of the scratches, and whether the wheel hub is broken, then clean the wheel hub and dry it with a towel; 2. Spray paint and apply oil: After applying putty, repaint the wheel hub. Before spraying, use old newspapers to isolate the edges of the wheel hub to avoid getting spray on the tire surface. Aim the wheel hub spray at the applied putty and spray back and forth a few times; 3. Fill the wheel hub scratches: The scratched areas of the wheel hub may be rough, so it is necessary to smooth them with fine sandpaper. Use wet sandpaper to sand the scratched areas repeatedly until smooth, then apply putty evenly.
16
1
Share

What does SVS displayed on the car dashboard indicate?

SVS displayed on the car dashboard indicates an engine malfunction. The reasons for displaying SVS are: 1. Poor gasoline quality leading to incomplete combustion of the air-fuel mixture in the cylinders, resulting in carbon deposits; 2. Excessive engine mileage causing weakened spark plug performance; 3. Mechanical aging of the vehicle; 4. Damage, poor contact, or signal interruption to components such as the water temperature sensor, crankshaft position sensor, air flow sensor, intake air temperature sensor, or oxygen sensor. Solutions for SVS displayed on the car dashboard: 1. Replace the oxygen sensor; 2. Replace the three-way catalytic converter; 3. Tighten or replace the fuel tank cap; 4. Replace the thermostat; 5. Replace the ignition coil; 6. Replace the air flow sensor; 7. Perform regular maintenance according to the schedule on the vehicle maintenance card.
20
0
Share

Can a Car with an Added Spoiler Pass the Annual Inspection?

Adding a spoiler to a car will not pass the annual inspection. During the annual inspection, the vehicle will be checked for modifications, alterations, or transformations. The inspection also verifies whether the vehicle's registration, license plate, and vehicle records match the actual condition of the car and if any changes have been made, including whether approval and modification procedures have been completed. The functions of a spoiler include: 1. Generating downforce during high-speed driving, increasing the car's grip and effectively reducing air resistance at high speeds; 2. Counteracting some of the lift, controlling the car's tendency to rise, reducing wind resistance, allowing the car to adhere closely to the road, thereby improving driving stability; 3. Enhancing the car's aesthetic appearance.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.