Is it normal for water to seep from the chassis of a Nissan Sylphy?

3 Answers
ElliotFitz
07/29/25 8:44am
Water seepage from the chassis of a Nissan Sylphy is normal drainage and should not be a problem. Below is an introduction to the Sylphy: 1. Overview: The Sylphy is a sedan series launched by Dongfeng Nissan Passenger Vehicle Company in 1959. In terms of health, the "in-car air quality" and "in-car noise" scores lead other models in the same batch. In terms of energy conservation and environmental protection, the "comprehensive fuel consumption" and "exhaust emissions" far surpass those of other models in the same batch. 2. Interior: Continuing the core comfort advantages of the Sylphy series, the 14th generation Sylphy offers a spacious five-seat layout and high-quality, lightly luxurious interiors, providing a delightful riding experience for the whole family. High-performance acoustic noise reduction technology and the NissanConnect intelligent system offer a relaxed and enjoyable driving scenario. 3. Performance: In addition to a significantly enhanced body structure, the 14th generation Sylphy is equipped with Nissan's unique IDM Intelligent Driving System. Starting with the 14th generation Sylphy, the Chinese family car market will enter an era of premiumization.
Was this review help?
1
4
Share
VanCameron
08/12/25 6:37am
Water seepage under the chassis is quite common on the Sylphy. As someone who frequently checks vehicle conditions, I don’t think it’s necessarily a major issue. Most of the time, it’s due to air conditioning condensate or rainwater accumulation draining to the underside. As long as the water is colorless and odorless, there’s little to worry about—it will naturally evaporate when the engine runs. However, be alert to unusual cases: if the water has color or odor, such as green coolant or oily fuel, it could indicate a broken pipe or gasket. Leaks onto the chassis may cause rust, weakening the frame, and electronic components are prone to short circuits, making the car undrivable. The Sylphy’s chassis is designed with drainage holes. I recommend first using a flashlight to inspect the seepage point—extra caution is needed if it’s near the engine or exhaust system. Wiping off wet spots after parking daily helps prevent rust. If the cause is unclear, visit a professional repair shop promptly for an inspection—a small expense for peace of mind. Don’t ignore it; chassis health directly affects the car’s lifespan.
Was this review help?
10
4
Share
Expand All
SanVictoria
10/05/25 8:05am
I've been driving a Sylphy for many years and have encountered water leakage under the chassis several times, especially after using the AC in summer or during rainy days. I don't think it's necessary to worry too much, as most of the time it's just normal condensation water discharge, which is fine if it drips onto the ground. However, if there's an unusually large amount of water or you notice strange odors inside the car, there might be an issue, such as a cracked pipe causing water accumulation that accelerates rusting. I usually clean the drainage holes under the chassis when washing my car to prevent blockages and reduce potential risks. Once, I found out that the AC pipe was loose after checking, and it only cost a few dozen yuan to have a mechanic adjust it. Regular observation and easy handling can help avoid unnecessary troubles.
Was this review help?
8
3
Share
Expand All
More Forum Discussions

How to Connect CarPlay in MG6 Infotainment System?

Ensure the CarPlay function on your phone is enabled. Connect your phone to the vehicle's infotainment system host using a USB cable. Tap 'Carplay' on the main interface to activate CarPlay. Once the connection is successful, you can operate your iPhone through the host. Press the return key on the control panel to return to the system's main interface.
16
3
Share

How to fix a broken motorcycle fuel float?

Directly disconnect the fuel level sensor connector and use a copper wire to make a direct connection to see if there is any change. If the gauge is working fine, the issue lies with the fuel level sensor. You can remove the fuel level sensor when the tank is low on fuel, directly connect the fuel level sensor, and move the fuel float to both ends to observe the changes in the fuel gauge needle. If the fuel float is stuck on the tank wall, readjust the fuel float support rod and reinstall it. This process might require two to three attempts.
18
4
Share

What is the method to reset the maintenance light on the Leopaard CS10?

Turn off the car's ignition switch, press and hold the TRIP button without releasing it. With the other hand, turn on the ignition switch to start the vehicle, then release the TRIP button. When the dashboard prompts for maintenance reset, press and hold the ENTER switch for 3 to 5 seconds. After hearing a beep from the dashboard, the process is confirmed complete, and the maintenance light will turn off.
1
1
Share

How to Control the Speed of an Automatic Transmission Car to be Slow Without Stopping?

There is no need to worry about stalling the engine. Simply shift the gear to D (Drive) and let the vehicle move naturally without pressing the accelerator. Just like driving in D gear, the vehicle is maintained by the engine idling, and the speed at this time is the slowest speed of the car.
6
0
Share

How to Replace the Door Frame Seal?

The seal is integrally connected with a U-shaped clamping part, featuring a section of sponge rubber edge, and the surface of the clamping part is covered with a flocking layer or velvet cloth. This design facilitates installation, ensures a tighter fit between the seal and the door opening sheet metal, and eliminates the wrinkling phenomenon at the corners of the door opening sheet metal during assembly.
20
0
Share

How to Clean a Clogged Car Air Conditioning Pipeline?

Weld off and remove the drying filter from both ends, separate the high and low pressure pipes, then block the low pressure pipe and start the compressor of the machine to make it work. Block the process pipe and weld shut the end of the low pressure capillary tube. The compressor starts working to self-suck, drawing moisture from the low pressure side to the high pressure side, thereby draining and clearing the moisture from the low pressure side. After powering off, quickly replace the drying filter, reconnect all pipelines, start the machine, and add refrigerant.
3
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.