Is It Normal for a Car Engine Hood to Be Hot to the Touch?

What are the differences between aluminum and steel used in automobiles?

Here are the differences between aluminum and steel used in automobiles: 1. Different weights: The most intuitive difference between aluminum and steel is the significant difference in density. If you hold them in your hand, the heavier one is steel, and the lighter one is aluminum. 2. Different surfaces: Aluminum does not rust in the air but only undergoes natural oxidation, appearing silver-white or dark gray. The natural surface of steel appears dull or rusty. 3. Different hardness: Steel is very hard, harder than most objects in nature. In contrast, aluminum is much less hard than steel. If you scratch them against each other, the harder one is steel. 4. Different magnetism: Ordinary steel objects are attracted to magnets, while aluminum has almost no magnetism. 5. Different resistivity: When measuring the resistivity of the two materials with a multimeter, aluminum has the lowest resistivity among various metal materials, and its conductivity is higher than that of steel.

20

2

Share

What to Do When the Car Headlight Cover Turns Yellow?

You can use specialized polishing wax to grind and polish the yellowed headlight cover. Minor yellowing and patterns can be removed. However, if the yellowing is very severe, you will need to go to a 4S shop or repair shop for replacement. Below are the specific steps for grinding and polishing the headlight cover: 1. Wash with soapy water. Soapy water is alkaline and will not corrode the headlight cover. 2. Soak sandpaper of different grits in cold water for 10 minutes, then evenly wipe the headlight housing, grinding back and forth in one direction. Keep the surface moist and apply moderate pressure to avoid damaging the surrounding paint or decorative strips. Continue until pits or scratches are smoothed out. Wipe gently with a towel and check if the grinding is even. Once done, dry the surface. 3. Use sandpaper dipped in water to lightly grind away the aged layer of the headlight cover. Then, apply a layer of polishing agent and finally spray a layer of clear oil for protection. 4. Some car headlights come with a built-in UV protection coating, which may be damaged during grinding. Use UV sealant to prevent further UV damage to the plastic.

9

0

Share

What Causes Ice Formation in the Car's Evaporator Box?

There are several reasons for ice formation in the car's air conditioning evaporator box: 1. The expansion valve's adjustment is too small, resulting in excessively low low-pressure. 2. Insufficient refrigerant in the system leads to excessively low evaporation pressure. 3. The internal circulation filter is clogged. 4. The temperature control (or temperature sensor) malfunctions, causing the compressor to run continuously. 5. The variable displacement compressor's energy control valve (pressure regulating valve) fails, keeping the compressor operating at full capacity, which results in excessively low low-pressure and causes the evaporator to freeze. Below are solutions for ice formation in the car's air conditioning evaporator box: 1. Check if the temperature control sensor is in the correct position. 2. Adjust the temperature control to a lower setting; if it cannot be adjusted, replace the temperature control. 3. Inspect the air conditioning computer control for any faults. 4. Apart from the compressor running continuously, check if the evaporator box fan's inlet and outlet dampers are blocked.

10

3

Share

How Long Can You Drive with Low Oil Pressure?

When low oil pressure occurs, it is recommended not to continue driving. Continuing to drive can lead to poor engine lubrication, exacerbating friction and wear on components. Additionally, oil plays a crucial role in cooling and heat dissipation. Low oil pressure can cause the engine to overheat internally, potentially leading to further damage such as bearing seizure or cylinder scoring. Below are the causes and solutions for low oil pressure: 1. Insufficient Oil Level: This issue is relatively easy to resolve—simply add the same type of oil. 2. Contaminants in the Oil: If there are impurities in the oil, they can clog the oil passages, resulting in low oil pressure. In this case, the oil needs to be replaced. 3. Oil Too Thin: If the oil is too thin, its sealing performance is compromised, allowing oil to leak through gaps and causing low oil pressure. This requires replacing the oil with a higher viscosity grade. 4. Faulty Oil Pressure Sensor: A damaged oil pressure sensor can lead to misjudgment of the oil's condition. In such cases, professional assistance is required for repairs.

8

5

Share

What is the Difference Between Multi-Link and Torsion Beam?

The differences between multi-link and torsion beam are as follows: 1. Multi-link suspension is an independent suspension, while torsion beam suspension is a non-independent suspension. In an independent suspension, each wheel is individually connected to the frame or body via an elastic suspension system, whereas in a non-independent suspension, the body and tires are not directly connected. 2. The multi-link independent suspension consists of links, shock absorbers, and damping springs. This type of suspension uses more links than a typical suspension. A four-link or five-link suspension is referred to as a multi-link independent suspension. 3. Due to the increased number of links used in this type of suspension, it allows the wheels to remain as perpendicular to the ground as possible, minimizing body roll to the greatest extent. This helps maintain excellent stability while driving. 4. The torsion beam non-independent suspension is not widely used in vehicles because this type of suspension has relatively high rigidity. The torsion beam independent suspension connects the two rear wheels of the vehicle on a single axle. When driving on rough road conditions, if one side of the wheel experiences jitter, the other side will also exhibit the same jitter phenomenon.

7

3

Share

What kind of oil does Toyota use?

Toyota vehicles use 0W20 or 5W20 engine oil. It is best not to use oil with a viscosity exceeding 5W30. Toyota vehicles are generally equipped with naturally aspirated engines, so standard oil will suffice. The functions of engine oil are as follows: 1. Reducing friction and high temperatures: A sufficiently thick oil film separates the surfaces of relatively sliding parts, thereby reducing wear. 2. Sealing effect: Engine oil can form a seal between the piston rings and pistons, reducing gas leakage and preventing external contaminants from entering. 3. Anti-rust effect: Lubricating oil adheres to the surface of parts, preventing contact with water, air, acidic substances, and harmful gases. 4. Cushioning effect: When the pressure in the engine cylinder rises sharply, suddenly increasing the load on the pistons, piston skirts, connecting rods, and crankshaft bearings, this load is transmitted and lubricated through the bearings, cushioning the impact load. 5. Cleaning effect: Good engine oil can carry carbon deposits, sludge, and worn metal particles from engine parts back to the oil tank through circulation, washing away dirt generated on the working surfaces of parts through the flow of the lubricating oil.

2

3

Share

Is It Normal for a Car Engine Hood to Be Hot to the Touch?

What are the differences between aluminum and steel used in automobiles?

What to Do When the Car Headlight Cover Turns Yellow?

What Causes Ice Formation in the Car's Evaporator Box?

How Long Can You Drive with Low Oil Pressure?

What is the Difference Between Multi-Link and Torsion Beam?

What kind of oil does Toyota use?

What does IAC mean in a car?

How Often Should the Oil in a Gasoline Generator Be Changed?

What is the normal discharge current for a car?

What are the causes of intake flow system performance failure?