Is it no longer necessary to display the 2021 inspection sticker and compulsory insurance sticker?

1 Answers
Quintero
07/29/25 4:53pm
First, the compulsory insurance sticker can be omitted in regions where electronic insurance policies have been implemented. As for the inspection sticker, it was fully digitized in 2020 and replaced by electronic inspection qualification certificates, so it is no longer required to display the inspection sticker. Relevant requirements for the digitization of motor vehicle inspection marks stipulate: 1. For vehicles exempt from inspection within 6 months: Vehicles that have already obtained electronic inspection qualification certificates do not need to display paper stickers. Traffic police will verify the inspection status of vehicles through law enforcement terminals during traffic management. 2. Inspection qualification: Motor vehicles must pass regular inspections, including exhaust emissions, vehicle appearance, lights, brakes, chassis, etc., and must have no traffic violation records to receive the inspection qualification mark. All inspection dates are based on the registration date on the vehicle's license, and motor vehicles must undergo safety technical inspections according to the following periods from the date of registration, referred to as 'annual inspection' or 'annual review'.
Was this review help?
8
2
Share
More Forum Discussions

Gear Grinding in Reverse with Dual-Clutch Transmission?

Gear grinding in reverse with a dual-clutch transmission is abnormal. It is usually caused by the clutch failing to disengage properly. Hazards of severe gear grinding in transmission: Transmission gear grinding essentially refers to the hard metal-on-metal contact between two gears. The outcome is obvious - accelerated wear on the gear crown. After prolonged and frequent occurrences, the originally right-angled gear crown becomes rounded. This leads to incomplete engagement after shifting gears, making it prone to gear disengagement with slight vibrations. At this point, a major transmission overhaul becomes necessary. When clutch gear grinding commonly occurs: It often happens when gear shifting is attempted without complete clutch disengagement. This not only produces gear noise during shifting but also easily causes gear grinding. Additionally, if the transmission lubricant contains large impurities, such as long-term wear metal shavings, these particles can get caught between meshing gears during rotation, also leading to gear grinding.
9
3
Share

Is the engine noise louder after switching to Shell oil?

The reasons for louder engine noise after switching to Shell oil are as follows: Excessive oil: Many car owners mistakenly believe that more oil is better. This is a misconception. There is a standard for oil quantity. If too much is added, it creates greater resistance to crankshaft rotation, affecting power output and increasing fuel consumption. Increased oil entering the combustion chamber leads to significantly more carbon deposits, increased piston movement resistance, reduced engine power, and a higher chance of knocking. Severe carbon deposits: Oil becomes thinner with use, leading to more carbon deposits. When new oil is added, the engine may not immediately adapt to the new oil's viscosity, causing higher RPMs and louder engine noise.
17
4
Share

How Long Can a Motorcycle's Annual Inspection Be Overdue?

Motorcycle annual inspection becomes invalid if overdue by even one day. Required documents for annual inspection: Original "Motor Vehicle License Plate Application Form" (signed by the authorized person for company vehicles, or by the owner for private vehicles), proof of compulsory motor vehicle traffic accident liability insurance, copy of the vehicle and vessel tax payment or tax exemption certificate, original motor vehicle safety technical inspection certificate, and original "Motor Vehicle Driving License". Annual inspection time regulations: The annual inspection time for vehicles is determined by the initial registration date of the new vehicle. For example, if the registration date on the motor vehicle driving license is June 2015, then the annual inspection time is every June. Additionally, according to Article 40 of the newly revised "Motor Vehicle Registration Regulations", vehicle owners can apply for the inspection compliance mark from the vehicle management office at the registration location up to three months before the expiration of the motor vehicle inspection validity period. This means that vehicles scheduled for annual inspection in June can undergo the inspection in April, May, or June.
3
1
Share

Why does a motorcycle lose power when it overheats?

Motorcycle overheating and loss of power can be caused by the following reasons: Excessive engine oil: Too much oil in the engine can affect heat dissipation and increase running resistance. You can drain the excess oil according to the oil level marks on the dipstick to fix the issue. (Common after engine oil changes or overhauls). Electrical component issues: One possible cause is faulty electrical components, such as the ignition coil, spark plug, or high-voltage coil. Replacing the faulty parts can resolve the issue. Engine timing gear misalignment: Another possible cause is misaligned engine timing gears, which can disrupt the ignition timing. This often occurs after engine repairs and can be fixed by reinstalling the timing gears correctly.
15
5
Share

Is Car Wash Required for Vehicle Inspection?

There is no mandatory requirement to wash the car, but it is better to have it washed before the annual inspection. Documents required for annual inspection: Original "Motor Vehicle License Plate Application Form" (signed by the authorized person for company vehicles or by the owner for private vehicles), Motor Vehicle Compulsory Traffic Accident Liability Insurance Certificate, copy of the vehicle and vessel tax payment or tax exemption certificate, original Motor Vehicle Safety Technical Inspection Certificate, and original Motor Vehicle Driving License. Annual inspection time regulations: The annual inspection time for a car is determined by the date of its initial registration. For example, if the registration date on the Motor Vehicle Driving License is June 2015, then the annual inspection time is every June. Additionally, according to Article 40 of the newly revised "Motor Vehicle Registration Regulations", the owner of the motor vehicle can apply for the inspection compliance mark at the vehicle management office up to three months before the expiration of the vehicle inspection period. This means that vehicles due for inspection in June can undergo the annual inspection in April, May, or June.
12
3
Share

What are the dimensions of a large parking space?

Large parking spaces are 15.6 meters long and 3.25 meters wide, suitable for medium and large vehicles. Parking spaces are divided into two types based on size: Large parking spaces are 15.6 meters long and 3.25 meters wide, suitable for medium and large vehicles; Small parking spaces are 6 meters long and 2.5 meters wide, suitable for small vehicles. Parking spaces are divided into three types based on arrangement: Parallel parking spaces: The standard length is 6 meters, and the width is 2.5 meters. Angled parking spaces (30°, 45°, 60° angles): The diagonal length should be 6 meters, the width should be 2.8 meters, and the perpendicular distance between the two diagonal lines should maintain a standard of 2.5 meters. Perpendicular parking spaces: The length should be greater than or equal to 5 meters, typically set at 6 meters, and the width should be 2.5 meters. Generally, 2.5x5.3 meters is considered the optimal standard parking space size.
4
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.