Is it necessary to replace the tire if the sidewall is punctured?

2 Answers
EthanDella
07/29/25 6:41am
For safety reasons, it is best to replace it promptly. The tire must be replaced if any of the following issues occur: 1. The diameter of the puncture hole in the tire crown exceeds 6 millimeters. 2. The sidewall is punctured or bulging. 3. The tire bead or tread is deformed, the rubber is corroded, or the tire is damaged due to underinflation and rolling. Here are some methods to extend the lifespan of your tires: 1. Avoid speeding: Excessive heat generated from high-speed driving can accelerate tire wear and reduce durability. 2. Avoid sharp turns, rapid acceleration, hard braking, and driving over curbs. 3. Try to avoid potholes and obstacles on the road, and slow down when driving on uneven surfaces.
Was this review help?
10
0
Share
OAurora
08/12/25 10:04am
As a friend who often helps others with car repairs, I have to say that a puncture on the tire sidewall usually means replacement is the only option. The sidewall is particularly thin and lacks the reinforcement of steel belts, so even if you manage to patch it, it won't withstand the pressure of high-speed driving. I've dealt with several cases like this recently—patched tires often develop bulges or leaks after a short time, making them even more dangerous. Especially in hot weather, the risk of a blowout increases as tire temperatures rise. If you must repair it, special internal patches are required, but the cost is similar to buying a new tire, and the results aren't reliable. Always park carefully to avoid scraping curbs, steer clear of deep potholes, and regularly check the sidewalls for bulges or cracks. When replacing tires, it's best to change them in pairs, as mismatched tread depths can affect traction.
Was this review help?
14
1
Share
Expand All
More Forum Discussions

Is it necessary to clean a car's air conditioning system?

It is necessary to clean a car's air conditioning system. After prolonged use, dust and dirt can accumulate in the air intake, air ducts, fan, and evaporator surfaces, leading to mold growth in the air ducts. Therefore, regular cleaning of the air conditioning system is required. The steps for cleaning a car's air conditioning system are as follows: 1. Start the car, turn on the air conditioning system, turn off the cooling function, and set the fan speed and temperature to the highest level. Switch the air conditioning to recirculation mode. 2. Close all car doors and windows, let the system run for 5-10 minutes, then activate the cooling function. Keep the fan speed at maximum and the air conditioning in recirculation mode, while setting the temperature to the lowest level. 3. Open the cap of the air conditioning cleaner bottle and place it in front of the front passenger seat or near the car's interior air intake. Press the valve on the bottle to allow the product to spray naturally. Let the product circulate in the enclosed car interior for 5 minutes. Then, turn off the air conditioning and open the car doors and windows for ventilation for 1-2 minutes to complete the cleaning process.
1
1
Share

Where does the license plate 'Lu C' belong to?

Lu C is the license plate of Zibo City, Shandong Province. Relevant information about license plates is as follows: 1. License plates, commonly known as vehicle plates, refer to the number plates hung on the front and rear of vehicles. They are usually made of aluminum, iron, plastic, or paper, and display the vehicle's registration number, registration area, or other related information. 2. License plates record the number and information of each vehicle. Their main function is to identify the vehicle's registration area through the plate, and they can also be used to trace the vehicle's owner and registration details. 3. Passenger car license plates are blue with white characters, while truck or motorcycle plates are yellow with black characters. Public security, armed police, and military vehicles use white plates with red characters.
5
2
Share

How to Solve Engine Overheating Issues

Solutions for engine overheating are as follows: 1. Sudden overheating. First, check if the radiator is excessively hot. If the radiator temperature is too high, it indicates a blown cylinder head gasket. In this case, inspect whether the mating surfaces of the engine block and cylinder head are severely warped or deformed, and repair promptly if necessary. If the radiator temperature is normal, it suggests poor coolant circulation. Examine whether the fan belt is broken or severely slipping. If these are normal, proceed to check if the radiator outlet hose is collapsed or internally obstructed by delamination. Identify the cause and address it accordingly. An emergency solution is to insert a properly sized spring inside the collapsed hose for support. Next, inspect whether the thermostat's expansion tube is ruptured and replace it if damaged. If the thermostat functions normally, the issue likely lies with a faulty water pump, which requires thorough inspection and repair. 2. Gradual overheating. For non-sudden overheating scenarios, increase engine RPM to observe if the filler neck shows coolant overflow, noting whether it's substantial or minimal. Substantial overflow with uneven radiator temperature indicates blocked coolant tubes, particularly common during severe winter conditions. When minimal overflow occurs accompanied by front-cool/rear-hot engine temperatures, it signifies a damaged or clogged water distribution pipe that needs immediate replacement.
6
4
Share

What does the car set mean?

set is the speed setting switch, which can store the current speed and automatically maintain this speed. When speed control is not needed, simply pressing the brake pedal will immediately stop the speed setting function, but the speed information continues to exist. To resume speed control, pressing the resume switch (Resume) will restore the originally stored speed, and the car can continue to drive at this speed. The usage of the Set button is as follows: 1. When using cruise control on the highway to maintain a speed of 120, if you want to reduce the speed to 100, you can release the accelerator until the speed drops to 100 and then press the set button, and the vehicle will continue to drive at a speed of 100. 2. If originally at a speed of 120, when we set the speed to 100 and press the set button, the vehicle will automatically decelerate to a speed of 100.
1
3
Share

What items need to be done for the second maintenance?

The items that need to be done for the second maintenance include: replacing the engine oil and oil filter, replacing or cleaning the air and cabin air filters, and inspecting and maintaining dozens of items across multiple systems such as the engine, transmission, air conditioning system, steering system, braking system, suspension, body, and tires. The precautions for car maintenance are as follows: 1. Regularly check whether antifreeze, brake fluid, windshield washer fluid, etc. are sufficient. Antifreeze ensures normal driving of the vehicle in winter and prevents freezing. Brake fluid is an essential component of the braking system. Windshield washer fluid is used to clean the windshield. All these must be kept sufficient to ensure the normal operation of the vehicle. 2. Perform wheel alignment regularly. 3. Regularly inspect the brake pads. Check the wear degree of the car's brake pads and clutch plates on schedule. When the car is driving on the road, the brake pads and clutch plates are constantly wearing. They need to be replaced when they reach a certain degree of wear, otherwise, there will be great safety hazards.
10
0
Share

What Are the Reasons for Increasing Car Fuel Consumption?

Car fuel consumption is increasing for the following reasons: 1. After cleaning the throttle body, the engine control unit was not matched or the matching was unsuccessful, leading to higher fuel consumption. 2. A fault in the engine's electronic control system causes an overly rich air-fuel mixture, resulting in increased fuel consumption. 3. Damage to the engine's ignition coils or spark plugs, or fuel injector leaks, leads to higher fuel consumption. 4. A malfunction in the engine cooling system causes the engine temperature to remain too low, keeping it in a warm-up state. 5. Excessive carbon buildup in the engine leads to incomplete combustion. 6. A fault in the fuel tank ventilation system causes fuel vapor leaks.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.