Is it necessary to repair transmission noise?

1 Answers
LeHaley
07/24/25 7:58pm
Transmission noise should be repaired. The causes of transmission noise failure are as follows: 1. Deformation of the transmission housing; 2. Loose or disassembled bearings; 3. Severe gear wear or broken teeth; 4. Overloading may cause bending of the transmission input or output shaft, or severe wear of the splines on the shaft; 5. Severe wear of the synchronizer. The following are the precursors of transmission failure: 1. Symptoms of transmission slipping. Fault performance: During driving, you can hear the engine idling when accelerating, but the car does not show a significant speed increase and has weak acceleration; another situation is that the car drives normally on flat roads but has weak power when going uphill, and the engine speed is very high. 2. Transmission noise. Fault performance: When the car is idling, driving, or under high-load driving, you hear abnormal noises from the transmission, even loud noises, and there are irregular, dull sounds when shifting gears. 3. Overheating of the transmission. Fault performance: The computer alarm shows that the transmission temperature is too high during driving; or after driving for a while, you feel that the transmission is overheating, even too hot to touch. 4. Symptoms of transmission oil leakage. Fault performance: You can clearly feel that the car is difficult to start, and during driving, although the engine speed increases when stepping on the accelerator, the car does not show obvious signs of acceleration.
Was this review help?
20
0
Share
More Forum Discussions

Why is the HUD missing in the Hongqi HS5?

If the HUD is not displaying, it could be due to issues with the display wiring connection or a problem with the HUD controller itself. You should check where the problem lies—whether it's with the projection device or the wiring. For this particular vehicle, it's best to have it inspected at a 4S dealership. Check the vehicle settings to see if the HUD option is enabled. Also, avoid placing any objects in the slot on the dashboard in front of the steering wheel, as that is the projection lens.
19
1
Share

How to align the timing marks on the Highlander 2.7 balance shaft?

First, rotate cylinder 1 to top dead center (TDC), then align the dot on the balance shaft gear. The balance shaft has a self-weighting force - rotate it to a specific angle for installation. Balance shaft technology is a simple yet highly practical engine technology that effectively reduces vehicle vibration and improves driving comfort. Common causes of loose balance shaft bearings and abnormal wear on bearing seats include poor engine balance and restricted movement of the rolling bearings.
18
4
Share

What to Do If the Steering Wheel of Haval M6 Is Too Heavy?

If it suddenly becomes very heavy or gradually gets heavier, it might be due to dirty power steering fluid, which is similar to engine oil and needs replacement. Low tire pressure increases the contact area between the tires and the road surface, leading to more friction and making steering more difficult, resulting in a heavy steering wheel. The tire pressure should be replenished promptly. Check the mechanical parts and the power steering system, or determine if there is any oil leakage or damage to the intake manifold seals.
18
4
Share

How to Restart a Manual Transmission Car After Stalling?

After a manual transmission car stalls, quickly engage the handbrake, shift to neutral, turn the key to the off position, press the clutch pedal with your left foot, place your right foot on the brake pedal, and then start the car with the key. To start a manual transmission car, first confirm the position of the handbrake, then check if the gear lever is in the neutral position, and then press the clutch pedal all the way down with your left foot. Turn the ignition switch step by step to the START position. Each starting attempt should not exceed 5 seconds. Once the engine stabilizes at idle speed, you can proceed to drive.
6
0
Share

How to Schedule Subject 2 Driving Test?

Download the "Traffic Management 12123" app, register your personal information, set a password, and complete the registration. Select Subject 2, check the agreement after entering, and then proceed to choose the test center; scheduling methods include self-selection and system arrangement. After the appointment is accepted, it will be displayed, and you can check whether the review is passed in the "Online Processing Progress"; if the review is passed, you will receive an SMS reminder.
11
3
Share

How to Start the Car When the Key Fob Battery Dies?

When the key fob battery for push-button start dies, you can use the spare mechanical key to start the car. Here are the relevant details: 1. Spare Mechanical Key: Regardless of brand or price, all car keys come with a built-in spare mechanical key—either foldable or hidden. 2. Mechanical Key Slot: Some car models hide the mechanical key slot inside the door handle for aesthetic reasons, requiring you to pry open a protective cover to access it. 3. Key Recognition Zone: Cars with push-button start functionality are equipped with an engine immobilizer system that matches a security code with the key. In this case, simply locate the designated key recognition zone in the car and place the key there to start the engine with the push-button.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.