Is It Necessary to Install a Shark Fin Antenna?

Is Using 95 Octane Gasoline Beneficial for Emissions During Annual Inspection?

During the annual inspection, if an engine designed for 92 octane gasoline is filled with 95 octane, the result will be incomplete fuel combustion, leading to unburned fuel being expelled as exhaust. In this scenario, the vehicle's emissions test will show excessive levels of hydrocarbons and particulate matter. Therefore, using 95 octane gasoline during the annual inspection is not beneficial for emissions. The differences between 92 and 95 octane gasoline are as follows: Different Anti-Knock Properties: The octane rating represents the fuel's anti-knock properties. A higher octane number indicates better anti-knock performance. Different Isooctane Content: 92 octane gasoline consists of 92% isooctane and 8% n-heptane, while 95 octane gasoline consists of 95% isooctane and 5% n-heptane. Different Prices: A tank of 95 octane gasoline is slightly more expensive than a tank of 92 octane gasoline.

18

5

Share

Should Spark Plugs Be Replaced After 20,000 Kilometers of Driving?

Generally speaking, spark plugs need to be replaced after a car has been driven for 20,000 kilometers. More relevant information is as follows: 1. It depends on the usage of the car. If the spark plugs are in good working condition, they do not need to be replaced. However, regular inspections are necessary during subsequent use. It is important to note that spark plugs made of different materials have varying service lives. If the car uses standard material spark plugs, it is recommended to replace them after 20,000 kilometers, as the condition of the spark plugs directly affects the car's acceleration performance and fuel consumption. 2. While driving, if you notice a lack of power in the car, it is necessary to check the condition of the spark plugs. A spark plug has a discharge electrode, and normally, the electrode gap should be between 1.0-1.2mm. If the gap is significantly larger, the spark plug may fail to discharge properly, leading to insufficient engine power. In such cases, the spark plugs should be replaced promptly. Prolonged use of worn-out spark plugs can cause excessive carbon buildup in the engine, which not only affects the car's power but also increases fuel consumption.

6

4

Share

Is a motorcycle with a seat height of 820mm suitable for a person who is 1.7 meters tall?

A motorcycle with a seat height of 820mm is not very suitable for a person who is 1.7 meters tall. Only the tips of the feet can touch the ground: For a motorcycle with a seat height of 820mm, a person who is 1.7 meters tall can at most touch the ground with the tips of their feet. It is almost impossible to have both feet flat on the ground. Generally, common motorcycles have a seat height of around 760mm, which allows a 1.7-meter-tall person to have both feet flat on the ground. Try it in the store if possible: Height and the bike's fit are not always standard. Some people may be shorter not necessarily because of shorter legs, but possibly due to a shorter torso or neck. Therefore, as long as the seat height is not excessively high, it is best to try it in the store. Sitting on the bike to test the fit is free, and the ideal scenario is to have both feet flat on the ground.

3

5

Share

Where is the Dayun Yuntu turn signal flasher located?

The turn signal switch is usually installed on the left side of the steering wheel. Operation method: It can be summarized as 'right' for up and 'left' for down. Turning the signal lever upward (clockwise) indicates a right turn, while turning it downward (counterclockwise) indicates a left turn. However, with the development of automobiles, many vehicles now have an 'one-touch three-flash' quick function added to the hazard light switch. The driver can lightly 'tap' the lever, and the turn signal will flash three times before automatically turning off. This allows the driver to avoid the hassle of manually turning off the signal when changing lanes or overtaking. Lighting operation: The turn signal has three positions: left-off-right. Using the steering wheel as a reference, pushing the lever clockwise activates the left turn signal, which can automatically reset with the steering wheel or be manually reset. Pulling the lever counterclockwise activates the right turn signal. For high/low beam switching: There are two positions, usually set to low beam. With the steering wheel as a reference, after turning on the headlight switch, pushing the lever downward activates the high beam, indicated by a steady blue light icon on the dashboard. Pulling the lever upward activates the low beam, turning off the blue icon. In the low beam position, pulling the lever upward serves as a passing light (high beam on) for signaling. Releasing the lever automatically returns it to the low beam position (if the light switch is off, the lights will turn off).

18

0

Share

Can only the scratched area be painted?

For those who do not have particularly high requirements, partial painting is acceptable. Differences in market painting: Currently, most of the market uses computer-mixed paint, which is then manually fine-tuned. This can basically match the original car paint color closely, but not exactly the same. The paint used is generally low-temperature paint. Original factory paint is high-temperature paint and is usually applied to the entire car. Therefore, if the requirements are not high, low-temperature paint can be used, which is relatively more convenient and can be applied anywhere. Car painting refers to applying a layer of paint to the car's surface to protect it. Car painting generally uses baking paint. In automobile manufacturing plants, after the frame and body are welded, the next step is painting. Types include ordinary paint, metallic paint, and pearl paint. Electrophoretic layer: Directly attached to the metal sheet, it plays a crucial role in preventing corrosion and rust on the car body. Three major leaps: Alkyd (enamel) paint in the 1920s; acrylic (enamel) paint in the 1960s; and clear coat in the 1980s. Thus, in the 20th century, car paint achieved significant advancements. For easier understanding, car paint can be simply categorized into ordinary paint and clear coat (mirror finish).

3

4

Share

Why is the turn signal not working?

Check whether the turn signal bulb is damaged and inspect the relay for any faults. The reasons for the turn signal not working are as follows: Check if the electrical hot wire has power: First, inspect whether the hot wire terminal of the flasher relay has power. If there is no power, check for any open circuit between the wire and the power source. If there is power, use a screwdriver to connect the two terminals of the flasher relay. If the turn signal lights up, it indicates a fault with the flasher relay, which should be replaced promptly. Inspect the flasher relay: If the light does not come on, the flasher relay should be checked. Open the cover of the flasher relay and inspect whether the coil and resistor are intact. If the resistor heats up but the contacts cannot close, press the movable contact. If the turn signal lights up at this point, it indicates a fault with the relay, which should be replaced. Fault with the turn signal switch: If the turn signal does not light up, it may be due to a fault with the turn signal switch. Use a screwdriver to connect the hot wire terminal of the turn signal switch with the left and right light wire terminals separately. If the light comes on, it indicates a fault with the turn signal switch, which should be removed for repair or replacement.

16

3

Share

Is It Necessary to Install a Shark Fin Antenna?

Is Using 95 Octane Gasoline Beneficial for Emissions During Annual Inspection?

Should Spark Plugs Be Replaced After 20,000 Kilometers of Driving?

Is a motorcycle with a seat height of 820mm suitable for a person who is 1.7 meters tall?

Where is the Dayun Yuntu turn signal flasher located?

Can only the scratched area be painted?

Why is the turn signal not working?

Can a motorcycle license be used to drive a motorcycle?

What is the working principle of a manual transmission breather valve?

Is it normal for the engine speed to be 1500 when starting the vehicle?

How to reset the tire pressure on a Buick GL8?