Is it necessary to go to a 4S shop for ACC calibration?

What is the normal tire pressure for the Verano?

The standard tire pressure for the Verano ranges from 2.4 to 2.5 bar, with variations depending on specific conditions. According to the international GBT29782008 standard requirements: standard tires should be inflated to 2.4-2.5 bar, reinforced tires to 2.8-2.9 bar, with the maximum pressure not exceeding 3.5 bar. In winter, it is advisable to slightly increase the tire pressure by approximately 0.2 bar based on the standard tire pressure. In summer, use the lower limit of the standard tire pressure. If the car is parked outdoors in summer, the pressure can generally be about 0.1 bar lower than the standard to prevent tire blowouts due to high temperatures. The standard tire pressure label for the vehicle can be found in at least one of these three locations: near the driver or passenger door frame, near the left instrument panel, or on the back of the fuel tank cap. The Verano has a body length of 4718 mm, width of 1802 mm, height of 1471 mm, and a wheelbase of 2700 mm.

6

0

Share

How often should the antifreeze in a Chevrolet Cruze be replaced?

The antifreeze in a Chevrolet Cruze should generally be replaced once a year. To prevent excessive foam formation, which reduces the heat exchange efficiency between the antifreeze and engine components, ensure the product is within its validity period when adding it. Long-life antifreeze can remain effective for up to three years. If suspended matter, sediment, or signs of deterioration or discoloration are found in the antifreeze, it should be replaced promptly, and the system should be cleaned. How to replace antifreeze: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with a particular focus on the five-way water pipe. The antifreeze is distributed to different parts of the car via the five-way pipe to perform its function. If there is any antifreeze leakage in this section, the water pipe should be replaced or the connection re-secured as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir and continue filling the reservoir so that water flows continuously through the engine cooling system. Then, start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially flowing out of the reservoir may appear slightly pinkish. Continue adding clean water until the water coming out is clear. Note: Remember to remove the heater hose and drain the water from the heater core. Approximately one hour after draining, add new antifreeze through the radiator hose. Then, add another container of antifreeze to the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is expelled from the cooling system. Top up the antifreeze until it reaches the "MAXT" mark on the reservoir.

16

0

Share

What is the actual fuel consumption of the Mazda Atenza 2.5?

The actual fuel consumption of the Mazda Atenza 2.5 ranges from 7.1 to 9.9 liters per 100 kilometers. Below are the detailed specifications of the Mazda Atenza 2.5: 1. Taking the 2021 Mazda Atenza 2.5 as an example, its body structure is a four-door, five-seater sedan with dimensions of 4870mm in length, 1840mm in width, and 1451mm in height, a wheelbase of 2830mm, front track of 1595mm, rear track of 1585mm, a fuel tank capacity of 56.2 liters, and a curb weight of 1559kg. 2. The 2021 Mazda Atenza 2.5 features a MacPherson independent front suspension and a multi-link independent rear suspension. 3. It is equipped with a naturally aspirated engine delivering a maximum horsepower of 192ps, a maximum power of 141kw, and a maximum torque of 252nm, paired with a 6-speed automatic transmission.

2

4

Share

Does the Audi Q7 have a seven-seat version?

Audi Q7 does offer seven-seat versions, specifically the 2019 55TFSI Technology Edition, 2019 55TFSI S line Sport Edition, and 2019 55TFSI Prestige Edition. The Audi Q7 is positioned as a mid-to-large-size SUV, with body dimensions of 5086mm in length, 1968mm in width, and 1716mm in height, and a wheelbase of 3001mm. It comes with two powertrain options: the first features a 2.0T inline 4-cylinder turbocharged engine paired with an 8-speed automatic transmission, delivering a maximum power of 185 kW and a maximum torque of 370 Nm; the second option is equipped with a 3.0L V6 supercharged engine, also matched with an 8-speed automatic transmission, producing a maximum power of 245 kW and a maximum torque of 440 Nm.

10

5

Share

What faults occur when the steering gear gets water inside?

There will be abnormal noises when turning the steering wheel in place, and the noises occur both when stationary and when driving at speeds not exceeding 20 km/h. Below is relevant information about the steering gear: 1. Introduction: The automobile steering gear, also known as the steering mechanism or steering box, is the most important component in the automobile steering system. Its function is to amplify the force transmitted from the steering wheel to the steering linkage and to change the direction of force transmission. 2. Types of steering gears: (1) Rack and pinion steering gear: This is the most common type of steering gear. Its basic structure consists of a pair of meshing small gears and a rack. When the steering shaft drives the small gear to rotate, the rack moves in a straight line. Sometimes, the rack directly drives the tie rod, enabling the steering wheels to turn. Therefore, this is the simplest type of steering gear. Its advantages include simple structure, low cost, sensitive steering, compact size, and the ability to directly drive the tie rod. It is widely used in automobiles. (2) Worm and sector steering gear: This type of steering gear uses a worm as the driving part and a sector as the driven part. The worm has trapezoidal threads, and finger-shaped conical pins are supported by bearings on the sector, which is integrated with the steering arm shaft. When steering, the worm is rotated via the steering wheel, and the conical pins embedded in the worm's spiral groove rotate while moving in an arc around the steering arm shaft, thereby driving the sector and steering arm to swing and causing the steering wheels to turn through the steering linkage. This type of steering gear is typically used in trucks that require greater steering force. (3) Recirculating ball steering gear: The recirculating ball power steering system mainly consists of two parts: the mechanical part and the hydraulic part. The mechanical part includes the housing, side cover, upper cover, lower cover, recirculating ball screw, rack nut, rotary valve core, and sector gear shaft. There are two pairs of transmission pairs: one is the screw and nut, and the other is the rack and sector gear or sector gear shaft. Between the screw and the rack nut, there are recirculating steel balls that convert sliding friction into rolling friction, thereby improving transmission efficiency. The advantages of this type of steering gear are easy operation, minimal wear, and long service life. The disadvantages are complex structure, higher cost, and steering sensitivity that is not as good as that of the rack and pinion type.

7

1

Share

Is the Steering Gear Noise on Bumpy Roads Related to Assembly?

Steering gear noise on bumpy roads is not significantly related to assembly. Below is relevant information about steering gears: 1. Introduction: The automotive steering gear, also known as the steering box or steering mechanism, is the most critical component in a vehicle's steering system. Its function is to amplify the force transmitted from the steering wheel to the steering linkage and to change the direction of force transmission. 2. Types of Steering Gears: (1) Rack and Pinion Steering: This is the most common type of steering gear. Its basic structure consists of a pair of meshing pinion and rack. When the steering shaft rotates the pinion, the rack moves linearly. Sometimes, the rack directly drives the tie rod, enabling the steering wheels to turn. Thus, it is the simplest type of steering gear. Its advantages include simple structure, low cost, sensitive steering, compact size, and the ability to directly drive the tie rod. It is widely used in automobiles. (2) Worm and Roller Steering Gear: In this type, the worm is the driving component, and the roller is the driven component. The worm has trapezoidal threads, and the finger-like tapered roller is supported by bearings on the crank, which is integrated with the steering arm shaft. When steering, the worm is rotated via the steering wheel, causing the tapered roller embedded in the worm's helical groove to rotate and move in an arc around the steering arm shaft, thereby driving the crank and steering arm to swing and ultimately turning the wheels. This type is typically used in heavy-duty vehicles requiring greater steering force. (3) Recirculating Ball Steering Gear: The recirculating ball power steering system consists of two main parts: mechanical and hydraulic. The mechanical part includes the housing, side cover, upper cover, lower cover, recirculating ball screw, rack nut, rotary valve core, and sector shaft. There are two pairs of transmission components: one is the screw and nut, and the other is the rack and sector or sector shaft. Between the screw and rack nut, there are recirculating steel balls that convert sliding friction into rolling friction, improving transmission efficiency. The advantages of this steering gear are ease of operation, minimal wear, and long service life. The disadvantages are complex structure, higher cost, and less steering sensitivity compared to rack and pinion steering.

14

4

Share

Is it necessary to go to a 4S shop for ACC calibration?

What is the normal tire pressure for the Verano?

How often should the antifreeze in a Chevrolet Cruze be replaced?

What is the actual fuel consumption of the Mazda Atenza 2.5?

Does the Audi Q7 have a seven-seat version?

What faults occur when the steering gear gets water inside?

Is the Steering Gear Noise on Bumpy Roads Related to Assembly?

What are the differences between gear positions?

How to Turn Off the Auto Start-Stop Function in Audi?

What brand is the Buick GL6 audio system?

What are the common reasons for high fuel consumption in J6P trucks?