Is it harmful to rev the engine in neutral?

1 Answers
Gimli
07/29/25 7:59pm
Revving the engine in neutral is harmful to the car. Precautions for using a car engine: 1. Avoid driving in neutral: The engine itself has a fuel-cut function during deceleration, and driving in neutral is not conducive to fuel economy; 2. Pay attention to observation when using the vehicle. If oil is found on the ground, determine whether there is an engine oil leak and communicate with the car 4S store in time to eliminate potential safety hazards; 3. For cars equipped with a turbocharger, do not turn off the engine immediately after high-speed driving or climbing a slope. Let the engine idle for 10 minutes before turning it off. Cars with turbochargers form carbon deposits several times faster than naturally aspirated cars.
Was this review help?
11
4
Share
More Forum Discussions

What engine does the Murano use?

Nissan's new Murano is equipped with the QR25 engine model, delivering a maximum horsepower of 186 hp, a maximum power output of 137 KW at 6000 rpm, and a peak torque of 243 Nm. The Nissan new Murano is paired with an Infiniti engine. Infiniti, as an automotive brand itself, is a premium brand under Nissan and also manufactures engines. For the Nissan new Murano's engine, the following maintenance methods can be applied in daily use: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will degrade during use. After a certain mileage, performance deteriorates, leading to various engine issues. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When engine oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve, carrying contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
14
4
Share

What are the reasons for the ABS light coming on in a Mazda?

ABS light can illuminate in various states, with different causes and solutions for each state. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections between system lines or poor contact in the ABS relay can cause signal issues, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage may drop below 10.5V. As the engine speed increases, the voltage rises, causing the ABS light to turn off. Another cause is insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, charging system, and power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS computer failure. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary. Check if the connector gap has widened. Replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant difference between the rear and front wheel speed signals. Incorrect tire or wheel rim specifications may also cause this issue. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, and push the brake switch linkage down with a finger to its limit. Then release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is recommended not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.
16
5
Share

What car has two stacked Rs?

The double R emblem is used by the British luxury car brand Rolls-Royce. Here is some information about the Rolls-Royce logo: 1. The double R logo of Rolls-Royce stands for the initials of its two founders, Charles Stewartrolls-Rolles and Henry Royce. 2. The famous Spirit of Ecstasy mascot was inspired by a 2,000-year-old statue of the Winged Victory of Samothrace in the Louvre Museum's art gallery. When automobile art master Charles Sykes was commissioned to design the emblem for Rolls-Royce Motor Cars, he incorporated the Winged Victory into his creative inspiration.
15
3
Share

How to Solve the Problem of Hard and Heavy Steering Wheel?

It is necessary to replace the power steering fluid of the motor vehicle. It is required to check whether the vehicle's steering gear is leaking oil. If there is leakage, it needs to be replaced. The steering column at the bottom of the steering wheel is lacking The steering column at the bottom is rubbing against the vehicle's floor mat, causing resistance. After identifying the specific cause of the fault, perform targeted repairs. After the repair, the vehicle's steering wheel will return to its normal state.
8
1
Share

How to Start a Baojun 730 When the Battery is Dead?

Here are the steps to start a Baojun 730 when the battery is dead: 1. First, open the vehicle's front hood; connect the positive cable of the emergency power source to the positive terminal of the battery, and the negative cable to the negative terminal. 2. Then, enter the vehicle and start it. Once the vehicle is running, quickly disconnect the cables from the battery. Be very careful not to let the two cables touch each other during the disconnection process. 3. Keep the engine running at around 2,000 RPM for a few minutes, or drive the vehicle for some time to complete the dead battery starting procedure.
5
3
Share

What does the same license plate type mean?

License plate type refers to license plates of different colors. Different types of vehicles require license plates of different colors. The same license plate type means that the vehicle license plates are of the same color. Common license plates: Common license plate colors include yellow, blue, and green. Most large buses and trucks require yellow license plates, while most ordinary household vehicles require blue or green license plates. The importance of license plates: License plates are mandatory for every vehicle to legally drive on the road. Driving without a license plate is illegal. To install a fixed official license plate, specialized anti-theft screws issued by the vehicle management office must be used.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.