Is it free to check engine failure at a 4S store?

1 Answers
DelConnor
07/29/25 10:33pm
Whether the car 4S store charges for inspection without repair depends on the situation. Generally, if the inspection is conducted within the warranty period, there is no charge. If the car is out of warranty, then a fee is required. Going to the car 4S store for fault inspection: Currently, the electronic control systems of cars are very advanced. As long as there is a vehicle fault, the onboard computer will generate a fault code. The car repair technician uses a computer to diagnose the fault code generated by the driving system, and then, based on the car owner's description, can quickly determine the location of the problem and provide targeted treatment. Car fault repair: When a car has a fault, it rarely requires the repair technician to dismantle the car and check the fault location bit by bit. Basically, the above method is used simultaneously. Therefore, if the car is out of warranty, going to the car 4S store for vehicle inspection is mostly charged.
Was this review help?
15
5
Share
More Forum Discussions

What Causes Excessive Engine Noise When Accelerating?

The causes of excessive engine noise when accelerating are as follows: 1. Excessive engine oil can increase the instantaneous working resistance of the engine, raising the crankshaft's rotational resistance and reducing the engine's output power. Additionally, excess oil may enter the combustion chamber and participate in combustion, leading to oil burning, blue smoke emission, and increased fuel consumption. 2. Incorrect engine oil type, such as switching from fully synthetic oil to mineral oil, can damage the engine. 3. Engine overheating, which causes power loss and abnormal noises. 4. Internal engine issues, such as valve clogging or similar problems.
15
3
Share

How to Solve Difficulties in Car Window Operation?

Solutions for difficult car window operation: 1. When the window is hard to move, lower it completely and spray panel wax into the rubber seals on both sides of the window. 2. After raising and lowering the window several times, if sticking or poor movement persists, lower the window completely again and reapply panel wax into the rubber seals. Repeat this process until the window operates smoothly without sticking, hesitation, or noise. Use a clean cloth to wipe away any excess panel wax from the window seals. This method can also prevent rubber seal aging and subsequent window operation issues. If this method doesn't work, visit a repair shop for professional assistance.
12
3
Share

What brand is the Civic?

Civic is a model under the Honda brand. Specific details are as follows: 1. Introduction: The Civic is a product of the joint venture between Japanese Honda Motor and China's Dongfeng Motor, manufactured by Dongfeng Honda. The first-generation Civic was launched in 1972, and the total sales of the Civic have exceeded 20 million units, distributed in more than 160 countries and regions worldwide. 2. Dimensions: The domestic new-generation Civic measures 4649*1800*1416mm in length, width, and height, with a wheelbase of 2700mm. The previous-generation Civic measured 4565*1755*1455mm with a wheelbase of 2670mm. The new-generation model has increased in length, width, and wheelbase.
4
1
Share

What is the tire model for the Mazda6 Atenza 2.0?

The Mazda6 Atenza 2.0 comes standard with Hankook VENTUS series tires, with the tire model being 225/55R17. Below is an introduction to the Mazda6 Atenza 2.0: 1. Exterior: It follows the design of the overseas version of the new Mazda6, featuring a larger front grille with an exaggerated design and a refined honeycomb mesh pattern inside. 2. Powertrain: It utilizes Mazda's SKYACTIV Technology. Compared to traditional naturally aspirated engines, the SKYACTIV engine in the Atenza boasts a high compression ratio of 13:1, improving fuel economy and torque by 15%. The 2.5L model of the Atenza accelerates from 0 to 100 km/h in just 8.3 seconds.
4
1
Share

What Causes the Car Dome Light Not to Work?

The car dome light not working is likely caused by a blown fuse in the vehicle's central control display. It is recommended to visit a repair shop to inspect the relevant fuses or wiring. Below are the steps to replace the dome light: 1. Start by removing the interior light trim panel from one corner. Use a small flat-head screwdriver to pry open the edge gap and release the small clips, separating them from the main body of the interior light. Once all four clips are released, the trim panel can be directly removed. 2. Observe the shape of the four clips, one at each corner. Place the interior light trim panel carefully to avoid scratching the surface. 3. The main body of the interior light is clipped onto the roof trim panel with two clips on the left and right sides. Separate these clips from the roof trim panel and gently pry them open with a screwdriver. 4. Install the new interior light bulbs one by one, then press the metal piece on the back of the main body of the interior light to secure the small bulbs, ensuring the connection is intact.
8
3
Share

What is a Cigarette Lighter?

Cigarette lighter is a device in a car. In the traditional sense, the cigarette lighter draws power from the car's electrical system to heat a metal heating element or wire, providing a flame source for lighting cigarettes. The related introduction of the cigarette lighter is as follows: 1. Besides lighting cigarettes, the car cigarette lighter can also be equipped with a car inverter, which converts the car's 12V, 24V, or 48V DC power into 220V/50Hz AC power for use with ordinary electrical appliances. For example, it can charge mobile electronic devices. 2. The correct way to use the cigarette lighter is to insert and remove it vertically without shaking. Frequent shaking during removal can cause looseness and short circuits, burning out the fuse and external devices.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.