Is It Difficult to Book the Driving Test Subject 3 in Dongguan?

1 Answers
JessicaLee
07/30/25 9:02am
Dongguan Subject 3 is difficult to book due to reasons such as a large number of people and limited road availability. Here is relevant information about the driving test: Definition of Driving Test Simulation Fee: The simulation fee and venue fee refer to the costs required for conducting a simulated test at the examination site. During the process of obtaining a driver's license, apart from the registration fee, simulation fee, and venue fee, there are no other charges. However, the decision to take the simulation test or not is entirely up to the individual—you can choose to simulate or not. Driving Test: Applicants for a motor vehicle driver's license must pass the following four subjects: Subject 1 (Road Traffic Safety Laws, Regulations, and Related Knowledge Test), Subject 2 (Site Driving Skills Test), Subject 3 (Road Driving Skills Test), and Subject 4 (Safe and Civilized Driving Knowledge Test). The test sequence follows Subject 1, Subject 2, Subject 3, and Subject 4 in order. Only after passing the previous subject can one proceed to the next.
Was this review help?
15
3
Share
More Forum Discussions

What Causes the Brake Lights to Stay On After the Car is Turned Off?

Reasons for the brake lights staying on after the car is turned off include severely worn brake pads, issues with the ABS sensor, a damaged brake switch, depleted brake fluid, or faulty brake lights. If the brake lights show abnormalities, they should be replaced promptly. Below is additional information about brake lights: Solutions for Brake Lights Staying On: To address brake lights staying on after the car is turned off, replace the brake pads; inspect the ABS sensor and replace it if damaged; replace the brake switch; replace the brake fluid; and check the brake light wiring. Function of Brake Lights: Brake lights are typically installed at the rear of the vehicle, with a red-colored body to enhance light penetration. This ensures that vehicles behind can easily detect when the car ahead is braking, even in low visibility conditions, helping to prevent rear-end collisions. Precautions When Replacing Brake Lights: In domestically produced vehicles, the taillights often serve a dual purpose, with two filaments inside the bulb—the weaker one for parking lights and the stronger one for brake lights. Some manufacturers design them as plug-in types with high and low pins, making them very convenient to use. When replacing, be careful not to reverse the connections.
20
1
Share

What are the causes of uneven tire wear?

Different types of uneven tire wear have different causes. For example, wear on both shoulder edges of the tire is due to insufficient tire pressure or overloading, while wear in the center of the tread indicates excessive tire pressure. Outer edge wear can result from excessive toe-in or camber angle, or a bent steering arm. Here are details about uneven tire wear: 1. Inner edge wear: caused by insufficient toe-in or camber angle. Feathering wear from the outer to inner edge is due to excessive toe-in, a bent steering arm, or unequal length of tie rods. 2. Feathering wear from the inner to outer edge: caused by excessive toe-out, a bent steering arm, etc. 3. Dish-shaped wear on the tread: This type of wear in one or more areas is caused by significant wheel imbalance, wheel bearing clearance, large wheel alignment deviation, ball joint clearance, tie rod clearance, bent axle, eccentric brake drum, as well as harsh braking, acceleration, and turning. 4. Wavy wear on the tread: caused by significant wheel imbalance, wheel bearing clearance, or large wheel alignment deviation.
6
4
Share

What Causes the Abnormal Noise from Brake Pads During Startup?

Abnormal noise from brake pads during startup can occur due to rain or other conditions that cause water to adhere to the brake discs. When the vehicle is left parked for a period, the surface of the brake discs can rust. Below is an introduction to brake pads: 1. Introduction: Brake pads are also known as brake linings. 2. Function: In a car's braking system, brake pads are the most critical safety components. The effectiveness of all braking performance is decisively influenced by the brake pads, making high-quality brake pads the guardian of both the driver and the vehicle. 3. Material: Brake pads (brake-lining) are generally composed of a steel plate, an adhesive heat insulation layer, and a friction block. The steel plate is coated to prevent rust, with the coating process monitored using an SMT-4 furnace temperature tracker to ensure quality by detecting the temperature distribution during coating. The heat insulation layer is made of non-heat-conductive materials to provide thermal insulation. 4. Principle: The friction block consists of friction materials and adhesives. During braking, it is pressed against the brake disc or drum to generate friction, thereby achieving the goal of decelerating the vehicle. Due to friction, the friction block gradually wears out. Generally, the lower the cost of the brake pads, the faster they wear out.
9
4
Share

Should You Drive an Automatic Car with One Foot or Two?

Since automatic cars do not have a clutch, it might theoretically seem possible to control the brake and accelerator separately with the left and right feet. However, developing such a poor driving habit can lead to confusion when switching to a manual transmission car, increasing the likelihood of mistaking the accelerator for the brake or vice versa. Here’s an introduction to automatic transmissions: 1. An automatic transmission eliminates the need for the driver to manually shift gears, as the vehicle automatically selects the appropriate gear based on driving speed and traffic conditions. A typical automatic transmission has six positions: P, R, N, D, S, and L. 2. Automatic transmissions use planetary gear mechanisms to shift gears automatically, adjusting based on the degree of accelerator pedal pressure and changes in vehicle speed. For everyday driving, using just the parking gear (P), reverse gear (R), neutral (N), and drive gear (D) is sufficient in an automatic car.
16
3
Share

Which Province Does the License Plate 'Jiang' Belong To?

In China, there is no vehicle license plate that starts with the character 'Jiang'. Such license plates only appear in TV dramas or movies to match fictional locations. These plates are not allowed on the road and are considered illegal. Even for filming purposes, prior approval from the traffic management department is required. Below is an introduction to vehicle license plates in various provinces of China: Beijing (Jing), Tianjin (Jin), Heilongjiang (Hei), Jilin (Ji), Liaoning (Liao), Hebei (Ji), Henan (Yu), Shandong (Lu), Shanxi (Jin), Shaanxi (Shaan), Inner Mongolia (Meng), Ningxia (Ning), Gansu (Gan), Xinjiang (Xin), Qinghai (Qing), Tibet (Zang). Hubei (E), Anhui (Wan), Jiangsu (Su), Shanghai (Hu), Zhejiang (Zhe), Fujian (Min), Hunan (Xiang), Jiangxi (Gan), Sichuan (Chuan), Chongqing (Yu), Guizhou (Gui), Yunnan (Yun), Guangdong (Yue), Guangxi (Gui), Hainan (Qiong), Hong Kong (Gang), Macau (Ao), Taiwan (Tai).
12
4
Share

What Causes the Squeaking Noise When Releasing the Brake During Startup?

Here are the reasons for the squeaking noise when releasing the brake during startup: 1. Releasing the brake too slowly when starting. When you gradually release the brake pedal, the engine already has sufficient power to drive the car forward, but the brake hasn't been fully released yet. As a result, the moving wheels are restrained by the brake system, naturally causing a squeaking noise. 2. The brake disc and brake pads are stuck together due to rust, causing the noise. This situation usually occurs after driving in rainy weather and then leaving the car unused for several days. The brake disc and pads rust and stick together, leading to noise when starting the car again. 3. The semi-metallic material of the brake pads. Brake pads contain a large amount of metal fibers, which sometimes form metal particles. These particles can produce a harsh noise when pressing or releasing the brakes. Typically, this noise disappears after driving for a while. If it persists, it may indicate poor manufacturing quality, and it's advisable to replace the brake pads promptly to avoid damaging the brake disc.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.