···
Log in / Register

Is It Correct to Use Hazard Lights on Rainy Days?

4 Answers
RebeccaLee
08/29/25 5:52am

Using hazard lights on rainy days is not entirely correct. According to Article 81 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China," in adverse weather conditions such as rain, fog, or snow, drivers should turn on fog lights, low beams, clearance lights, and front and rear position lights. Hazard lights can only be used in conjunction with fog lights when visibility is less than 100 meters. Below are some relevant guidelines on the use of hazard lights: 1. Vehicle accidents or malfunctions: In such cases, it is necessary to promptly turn on the hazard lights and place a triangular warning sign one to two hundred meters behind the vehicle to alert surrounding drivers of the issue and prompt them to slow down. 2. Temporary parking: If parking is required on a road where temporary stopping is allowed, hazard lights should be turned on. However, parking in a no-stopping zone with hazard lights on constitutes a traffic violation. 3. Towing a malfunctioning vehicle: Both the towing vehicle and the malfunctioning vehicle being towed must have their hazard lights on during the towing process.

Was this review help?
16
4
Share
SanOlivia
09/11/25 3:32am

I remember one time when it was raining heavily, and I was driving on the highway. I saw many people turning on their hazard lights, and I thought it was quite normal, assuming it would make me more noticeable to others. However, this is actually very dangerous because hazard lights are meant to indicate emergency situations, such as a vehicle breakdown or an accident. Turning them on can confuse other drivers. Visibility is already low in rainy conditions, and if you turn on your hazard lights while making a turn, others might completely miss your turn signal, leading to rear-end collisions or misjudgments. The correct approach is to turn on your low-beam headlights or fog lights (if your vehicle has them), maintain a safe distance from the car in front, and avoid driving too fast. This effectively increases your visibility and prevents unnecessary hazards. From a safety perspective, I always remind my friends not to take the easy way out by using hazard lights unless there’s a real problem. Developing good habits can save you from big troubles.

Was this review help?
16
0
Share
Expand All
KaydenMarie
10/25/25 4:21am

I usually pay close attention to driving rules. On slippery roads during rainy conditions, turning on hazard lights is absolutely incorrect because they are specifically designed for emergency stops. If you use them casually, it can distract drivers behind you and obscure your actual intentions. I once witnessed a case where someone used hazard lights in heavy rain, and when they turned, their signal was drowned out, leading to a minor collision. Now when driving, I insist on using only low beams and fog lights to improve visibility while ensuring both interior and exterior mirrors remain clear. The key to rainy-day safety lies in anticipation and composure—slow down, avoid waterlogged areas, and never rely on hazard lights as regular lighting. This not only protects yourself but also helps maintain smooth traffic flow. Regularly reading safety manuals or watching related videos can be lifesaving—these small tips can make all the difference.

Was this review help?
3
3
Share
Expand All
VanMelanie
12/08/25 4:45am

When I first started learning to drive, I liked to turn on the hazard lights on rainy days, thinking the flashing lights made me extra safe. Later, a driving instructor pointed out to me: hazard lights are designed for real emergencies, not for casual use. In the rain, they can easily confuse other drivers about your intentions, actually increasing the risk. The correct approach is to use low beams or fog lights, which clearly indicate your position. Now, I’ve made it a habit—whenever the weather is bad, I immediately turn on the main lights. Remember, safe driving isn’t just about you; it’s about everyone else on the road. Learn these small tips, and don’t let bad habits become hazards.

Was this review help?
11
2
Share
Expand All
More Forum Discussions

Where is the water temperature gauge on the Honda XRV?

The Honda XRV does not have a water temperature gauge. Below is an introduction to the water temperature indication and the function of the engine water temperature gauge for the Honda XRV: Water temperature indication for the Honda XRV: When the water temperature is high, there will be a water temperature warning on the dashboard. The Honda XRV water temperature is indicated from C-H, where C represents 60 degrees. As soon as the needle reaches C, it means the water temperature has reached 60 degrees. The H red mark represents a temperature of 110 degrees. The span from 60 to 110 degrees allows for an estimation of the water temperature. Function of the engine water temperature gauge: The engine water temperature gauge is used to indicate the temperature of the engine coolant. The coolant temperature signal is provided by the engine coolant temperature sensor installed on the engine cylinder head. During normal engine operation, the displayed value should be between 80-100 degrees.
11
3
Share

What kind of engine oil should be used for Toyota RAV4?

Toyota RAV4's original engine oil brand is Toyota Genuine Motor Oil. For later maintenance and oil changes, you can choose brands such as Shell, Mobil, Castrol, or Total. The official Toyota RAV4 manual recommends oil specifications of 0W-20, 5W-20, 5W-30, and 5W-40. Any oil model that meets these four specification parameters can be used. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W represents the ability to withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The latter number represents the kinematic viscosity of the oil at 100°C. A higher value means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in a Toyota RAV4 is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan; Use a wrench to loosen the oil drain plug and place an oil pan to catch the old oil until the flow stops. Start the engine for about 30 seconds to allow the oil in the main oil passage to drain out; Use a specialized wrench to remove the oil filter; Apply oil to the seal of the new oil filter and tighten it clockwise by hand; Add the new engine oil through the oil filler cap on the engine valve cover, typically filling about three-quarters of the oil container; Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If leaks are found, repairs should be made; After stopping the engine, pull out the oil dipstick to check that the engine oil level is within the standard range.
17
1
Share

Why Are the Dashboard Lights Not Working?

Car dashboard lights not working are caused by faults in the dashboard illumination lights, dashboard power supply wires, or dashboard power supply fuses. Below is a related introduction to car dashboards: Dashboard Lights Not Working: If the car dashboard lights are not working, three areas need to be checked: the dashboard illumination lights, dashboard power supply wires, and dashboard power supply fuses. After inspection, replace any damaged components. Car Dashboard: The car dashboard is a device that reflects the working conditions of various vehicle systems. Common indicators include the fuel light, washer fluid light, electronic throttle light, front and rear fog light indicators, and warning lights. Dashboards vary between different cars; however, conventional car dashboards typically include a speedometer, tachometer, oil pressure gauge, water temperature gauge, fuel gauge, and charging gauge.
16
5
Share

What is the belt model for Komatsu 200-7?

Komatsu 200-7 belt model name: 20Y-70-32361. Timing belt: The timing belt is an important component of the engine's valve timing system. It connects to the crankshaft and ensures accurate intake and exhaust timing through a specific transmission ratio. Belts are used instead of gears for transmission because they produce less noise, have minimal variation, and are easier to compensate for. Function of the timing belt: The timing belt serves as a link between the upper and lower parts of the engine. The upper part connects to the timing pulley on the engine cylinder head, while the lower part connects to the crankshaft timing pulley. The timing pulley is connected to the camshaft, which has cams that contact small rocker arms. The rocker arms generate pressure through the power transmitted by the timing belt, performing a lifting action. Lifting the intake valve allows atomized gasoline to enter the cylinder, while lifting the exhaust valve allows exhaust gases to exit the cylinder. When the recessed part of the camshaft contacts the rocker arms simultaneously, both the intake and exhaust valves close, creating compression. The distributor then sparks, initiating combustion and generating power.
11
2
Share

Is it useful to install a turbocharger on a car?

Installing a turbocharger on a car is useful. Here is an introduction to the benefits of installing a turbocharger on a car: Increase engine power per liter: Without changing the engine displacement, the intake air density can be increased, allowing the engine to inject more fuel, thereby increasing the engine's power. After installing a turbocharger, the engine's power and torque can increase by 20%-30%. Conversely, under the same power output requirements, the engine's bore can be reduced, shrinking the engine's size and weight. Improve fuel economy: Since engines with turbochargers have better combustion performance, they can save 3%-5% of fuel; they also have high reliability, good matching characteristics, and excellent transient response characteristics.
16
5
Share

How Long Does a 4AT Transmission Last?

With proper use and maintenance, the service life of a 4AT transmission can reach 600,000 kilometers. Below is an introduction to AT transmissions and other types of transmissions: AT Transmission: This is a relatively common type of automatic transmission. Its structure is quite complex, but AT transmissions are the most mature in technology and the most widely used automatic transmissions. They are also known as torque converter transmissions because they are connected to the engine via a torque converter. Other Transmissions: Common automatic transmissions in vehicles also include CVT transmissions and dual-clutch transmissions. In a dual-clutch transmission, one clutch controls the odd-numbered gears, while the other controls the even-numbered gears. A CVT transmission is a simpler type of automatic transmission, consisting of only two pulleys and a steel belt inside.
1
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.