Is it better to use 92 or 95 octane gasoline for the Geely Vision?

3 Answers
Pinto
07/29/25 5:50pm
Geely Vision is equipped with a 1.5-liter naturally aspirated engine across the entire lineup, so this vehicle can use 92 octane gasoline. Gasoline with different octane ratings has different levels of octane; the higher the octane rating, the higher the octane value, and gasoline with higher octane values is more stable. Generally, 92 octane gasoline is sufficient for naturally aspirated engines in family cars. Here is some information about the Geely Vision: 1. The Geely Vision is a compact sedan under the Geely brand. Its 1.5-liter naturally aspirated engine delivers 109 horsepower and a maximum torque of 142 Nm. The engine reaches its maximum power at 6000 rpm and its maximum torque at 4400 rpm. This engine features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. 2. The Geely Vision's engine is paired with either a 5-speed manual transmission or a CVT. The CVT is a common type of automatic transmission that is very suitable for family cars. The front suspension of the Geely Vision uses a MacPherson independent suspension, while the rear suspension employs a torsion beam non-independent suspension.
Was this review help?
12
3
Share
WyattLee
08/14/25 9:33am
As a long-time owner of a Geely Vision, I've found that using 92-octane gasoline is the most cost-effective choice after driving it for several years. The engine's compression ratio in the Vision isn't particularly high, so 92-octane fuel is perfectly adequate, providing stable performance while saving money. Although 95-octane gasoline is slightly more expensive per liter, the difference adds up to several hundred yuan more per year in the long run—money that could cover an oil change. Unless you're frequently driving at high speeds on highways or tackling steep mountain slopes, 92-octane is perfectly suitable. For daily city commutes and school runs with kids, 92-octane is sufficient, and using 95-octane would be an unnecessary luxury. Always choose reputable gas stations to ensure fuel quality, and avoid the temptation of cheaper fuel from small, unreliable vendors.
Was this review help?
16
2
Share
Expand All
Bella
10/14/25 2:37am
From a driving experience perspective, I've compared 92 and 95 octane fuels. The 95 octane offers slightly better power and faster acceleration, making the Vision feel more spirited to drive. However, the engine really doesn't require such premium fuel - 92 octane fully meets normal driving needs. While 95 octane's higher rating helps prevent knocking, the Vision was designed with 92 octane compatibility in mind. Using 95 might slightly extend engine life or reduce carbon buildup, but the higher cost doesn't justify these marginal benefits. I still recommend sticking with 92 octane as the primary choice - it's both economical and reliable.
Was this review help?
17
3
Share
Expand All
More Forum Discussions

What is the tire model for Toyota Camry?

Toyota Camry tire models include 205/65R16, 215/55R17, and 235/45R18. Relevant information about car tires is as follows: Tire Classification: Car tires can be divided into pneumatic tires and solid tires based on their carcass structure. The vast majority of modern cars use pneumatic tires. Depending on the air pressure inside the tire, pneumatic tires can be categorized into high-pressure tires, low-pressure tires, and ultra-low-pressure tires. Tire Specification Meanings: Tire specifications are often represented by a set of numbers. The first number indicates the tire section width, and the latter indicates the rim diameter, measured in inches. For example, 165/70R14 means a tire width of 165 millimeters, an aspect ratio of 70, and a rim diameter of 14 inches. The letters or symbols in the middle have special meanings: "X" denotes a high-pressure tire; "R" and "Z" denote radial tires; "—" denotes bias-ply tires. For example, 6.00—12 refers to a bias-ply tire, which is only used in some low-end off-road vehicles and heavy-duty trucks due to its poor safety, load capacity, and high-speed stability.
10
0
Share

What is the difference between the car's internal circulation and external circulation?

Internal circulation means that the air inside the car circulates when the car is closed. The icon is a closed car interior with a circulating arrow; while external circulation means that the air outside the car flows into the car. The icon is an unclosed car with an external air arrow pointing into the car. The specific differences are as follows: 1. Internal circulation refers to the air inside the car being heated or cooled before being sent back into the car; external circulation refers to the air outside the car being heated or cooled before being sent into the car, which means gas exchange between the inside and outside of the car. 2. Generally, when we turn on the air conditioning for cooling or heating, we can first turn on the internal circulation to quickly lower or raise the temperature inside the car; when the temperature stabilizes, we can appropriately switch to external circulation to exchange air with the outside. If the air quality outside the car is not good, such as in traffic jams with a lot of exhaust fumes or in underground parking lots, do not turn on the external circulation. If you are driving on the highway, do not open the car windows, just turn on the external circulation. When the air outside is good and you feel stuffy inside the car, quickly turn on the external circulation for air exchange; if you want to maintain the air inside the car, turn on the internal circulation.
6
4
Share

How to Use Cruise Control on Baojun 510?

Here are the operating steps for cruise control on the Baojun 510: 1. Press the ON/OFF button to activate cruise control. The CRUISE/MAIN indicator light will illuminate, indicating the cruise control system is operational. 2. Accelerate to the desired speed using the accelerator pedal, then press the SET/COAST button (allowed when speed exceeds 30Km/H) to set the current speed. The CRUISE indicator light will illuminate. Release the accelerator pedal, and the vehicle will maintain the set speed. Keep your right foot near the brake pedal to handle emergencies. 3. During cruise control, press the RES/ACCEL button to increase speed or the SET/COAST button to decrease speed, adjusting the cruising speed as needed. Additional information for cruise control operation on curves or when decelerating: 1. Press the CANCEL button or lightly tap the brake pedal to temporarily deactivate cruise control. The CRUISE indicator light will turn off. Coast to decelerate or control speed with the accelerator pedal. After exiting the curve, press the RES/ACCEL button to resume the previously set speed. 2. Hold down the SET/COAST button or press it repeatedly (each press reduces speed by 1.6Km/H) until reaching the desired speed. After exiting the curve, hold down the RES/ACCEL button or press it repeatedly (each press increases speed by 1.6Km/H) until reaching the desired speed.
6
3
Share

What are the reasons for the non-illumination of the center console screen in the eighth-generation Accord?

The reasons for the non-illumination of the center console screen in the eighth-generation Accord include abnormal power supply to the display, poor contact of the wiring harness, damage to the display screen, incorrect use of the USB port in the center armrest, faulty power switch circuit, and outdated firmware. Solutions for the non-illumination of the center console screen: Abnormal power supply to the display: The power supply module needs to be replaced. Poor contact of the wiring harness: The wiring harness needs to be replaced. Damage to the display screen: It is necessary to go to a 4S shop for repair. Incorrect use of the USB port in the center armrest: Inserting incompatible cables into the USB port in the center armrest can cause the screen to go black. Removing the USB cable can solve the problem. Faulty power switch circuit: The driver should go to a car 4S shop for repair. Outdated firmware: Failure to upgrade the multimedia system on time can cause the screen to go black. The driver needs to go to a car 4S shop for an upgrade, and upgrading to the latest firmware can resolve the issue.
1
2
Share

How to Check Engine Model Number from Engine Number?

You can find out the engine model number by checking the engine number. The vehicle's nameplate displays specific information about the car, such as the chassis number (vehicle frame number), engine number, vehicle weight, model, and other basic details. The engine number is also marked on the engine block—note that it is not on the cylinder head but on the lower block. Therefore, with the engine number, you can directly look up the engine model. Composition of Engine Model Number: Prefix: Includes product series code, generation symbol, and regional/enterprise code. Manufacturers may choose appropriate letters as needed, but these must be approved and filed by the industry standardization authority. Middle Section: Consists of symbols for the number of cylinders, cylinder arrangement, stroke, and cylinder diameter. Suffix: Distinguishing symbol. For differentiating products within the same series due to improvements or other reasons, manufacturers may select appropriate symbols. The suffix can be separated from the middle section using a "-". The engine model number is an identification code assigned by the engine manufacturer in accordance with regulations, industry practices, or the engine's attributes to a batch of identical products. It represents information such as the manufacturer, specifications, performance, features, technology, purpose, and production batch—including fuel type, number of cylinders, displacement, and brake power.
5
0
Share

How to Downshift for Overtaking Without Jerking?

Reduce speed before downshifting. If you downshift without reducing speed first, jerking is inevitable. Jerking occurs when the gear ratio and throttle are mismatched. Properly reduce your speed, depress the clutch, and as you release the clutch, simultaneously apply the throttle. This ensures quick acceleration without jerking. With good coordination between the throttle and clutch, and by releasing the clutch slowly, you can avoid jerking altogether. Below are specific methods for downshifting to overtake without jerking: 1. The moment you upshift, the engine speed drops immediately while the vehicle speed remains constant. Additionally, as the transmission gear ratio decreases, the torque output from the engine to the wheels also decreases. After completing the upshift, you accelerate by pressing the throttle, but due to the reduced torque output, the acceleration is relatively slow. Conversely, the moment you downshift, the engine speed increases immediately while the vehicle speed remains constant. At the same time, as the transmission gear ratio increases, the torque output from the engine to the wheels also increases. 2. After completing the downshift, you typically reduce speed by easing off the throttle (so-called deceleration downshifting). Due to the increased torque output, pressing the throttle at this point generates significant acceleration, allowing the vehicle to speed up quickly. This meets the requirements for overtaking, as overtaking demands instant high acceleration. The acceleration produced by upshifting and pressing the throttle is far less than that produced by downshifting and pressing the throttle. Although the latter may cause the engine speed to exceed the normal range temporarily, it quickly returns to normal after overtaking.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.