Is Engine Maintenance Fluid Useful?

1 Answers
Maverick
07/29/25 8:05pm
Engine maintenance fluid is useful. Here are the functions of engine maintenance fluid: 1. Protect the engine: Significantly reduce engine wear, effectively prevent engine overheating, and extend engine life. 2. Enhance the comprehensive performance of lubricating oil: It has a significant improvement for both synthetic and mineral oils. 3. Improve engine power: Makes the engine run more smoothly and with lower noise. 4. Clean the engine: Effectively cleans the engine and prevents carbon deposits. Here are the reasons that may cause engine stalling: 1. Sensor resistance: The crankshaft position sensor's own resistance is abnormal, causing the crankshaft speed signal to disappear after the engine heats up, leading to engine stalling. 2. Fuel pressure: The gasoline pump's resistance changes after prolonged operation, unable to provide normal fuel pressure, resulting in engine stalling. 3. Ignition failure: Ignition system failure or overheating of the ignition module prevents normal operation, causing engine stalling.
Was this review help?
7
1
Share
More Forum Discussions

What is the correct way to warm up the Trumpchi GS3?

The correct way to warm up the Trumpchi GS3 is: After a cold start, let the engine idle for about 1 to 2 minutes until the RPM stabilizes, then you can start driving. Avoid rapid acceleration during this period. Once the engine temperature rises to the normal operating temperature, you can drive normally. Prolonged idling to warm up the engine can easily lead to carbon buildup. The Trumpchi GS3 features a family-style "Soaring Wings" grille similar to the GS4, seamlessly integrated with stylish headlights. The front bumper also adopts a dynamic design on both sides. The vehicle is equipped with a three-spoke multifunction steering wheel, a rectangular instrument panel, a large-size display screen, rear air conditioning vents, seat heating, one-button start, keyless entry, rearview camera, electronic parking brake, and auto hold.
3
3
Share

Why does the car start but not move?

The reasons why the car starts but does not move are as follows: 1. Worn clutch plate: needs replacement. Due to severe wear of the clutch plate, it loses friction and can no longer transmit the engine's power to the transmission, failing to establish effective power transfer. 2. Car out of fuel: causing the car to be unable to move. Battery depletion, insufficient power to drive the starter motor, resulting in inadequate motor speed. Additional information: 1. Car ignition system: For spark-ignition engines to operate normally, the system supplies the spark plugs with sufficiently high-energy high-voltage electricity (approximately 15,000 to 30,000V) in the correct firing order for each cylinder, generating a strong enough spark to ignite the combustible mixture. 2. Traditional ignition: The mechanical ignition system operates by the crankshaft driving the distributor shaft, which rotates a cam to open and close the primary contacts of the ignition coil, thereby generating high voltage.
2
3
Share

Can I still pass after failing the driving test four times?

If you haven't passed the driving test after four attempts, you need to calm down first and think about why. The driving test requires a lot of learning and practice, which is essential. During the usual practice, you should listen carefully to the instructor's explanations and take note of the areas where points are easily deducted. Before the actual test, be sure to go to the test site for simulation practice to familiarize yourself with the test environment and have a clear understanding. The following is an introduction to the content of the driving test: Starting: vehicle preparation, starting, and driving straight. Speed control: shifting gears, changing lanes, and parking by the side of the road. Turning: going straight through intersections, turning left at intersections, and turning right at intersections. Passing specified areas: passing crosswalks, passing school zones, and passing bus stops. Vehicle control: meeting other vehicles, overtaking, turning around, and driving at night.
7
5
Share

What are the classifications of electric vehicle batteries?

Currently, the batteries used in electric vehicles are: ternary lithium batteries, lithium iron phosphate batteries, and nickel-metal hydride batteries. Among them, nickel-metal hydride batteries are the most stable, lithium iron phosphate is the safest, and ternary lithium batteries have the highest capacity. Below is a detailed introduction: Ternary Lithium Battery: Good at teamwork, with the highest capacity for the same weight. However, the components are tightly packed together, leading to slightly higher temperatures. Therefore, ternary lithium batteries have stringent cooling requirements, and for safety, each battery cell must have a protective device. Lithium Iron Phosphate Battery: Highly favored by most automakers. Although its capacity per unit weight is not as high as that of ternary lithium batteries, it has excellent thermal stability, is less prone to overheating, and requires much lower costs for cooling components. Additionally, it offers advantages such as high energy density, compact size, long battery life, and good safety.
17
5
Share

Is Manual Evaluation Used for Subject 2 of the Driving Test?

Subject 2 of the driving test does not require manual evaluation; the entire process is automatically assessed by a computer. Introduction to Subject 2: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the field driving skills test. For the C1 license, the test items include five mandatory components: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and curve driving (commonly known as the S-curve). In some regions, there is a sixth item: high-speed card collection. For the C2 license, the test includes four mandatory components: reversing into a garage, parallel parking, turning at a right angle, and curve driving (commonly known as the S-curve). Precautions for Subject 2:
16
0
Share

What does the sync button in the car mean?

The sync button in the car means: 1. Function synchronization: It refers to the synchronization of functions, generally used for car air conditioning. 2. Sync button: It is a dual-zone synchronous temperature control button. After releasing it, different temperature settings can be achieved for the left and right dual-zone air conditioning. Precautions for using car air conditioning: 1. Regularly clean the air conditioning: During use, the air conditioning often inhales a certain amount of dust, forming dirt. After a long time, mold may develop. 2. The air conditioning temperature should not be too low: When the indoor temperature remains at a relatively low temperature for a long time, the body cannot quickly adapt due to the endocrine system, leading to various discomforts. 3. Do not stop and rest with the air conditioning on: When the car engine is running, if the gasoline in the cylinders does not burn completely, it will produce a high concentration of carbon monoxide, which can cause poisoning or even death.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.