Is Electric Four-Wheel Drive the Same as Full-Time Four-Wheel Drive?

What are the symptoms of a broken car stabilizer bar?

The symptoms of a broken car stabilizer bar are as follows: 1. If the car's stabilizer bar is damaged, there will be noise when driving on rough roads, but no abnormal sounds on paved roads. 2. If the stabilizer bar is damaged, the car's body roll will increase when cornering. 3. The car stabilizer bar connects the shock absorbers of the left and right wheels on the same axle, which helps reduce body roll during cornering. 4. Some expensive cars are even equipped with electronic stabilizer bars, which have a motor in the middle that plays a significant role during cornering. If the car is equipped with an electronic stabilizer bar, there is almost no body roll when cornering.

8

0

Share

Can Plastic Bumpers Be Repaired with Sheet Metal Work?

Yes, it can be done. Automotive sheet metal work is a technical method of car repair, where this aspect of sheet metal work is equivalent to automotive sheet metal repair. It refers to the process of restoring the car body after a collision, encompassing all tasks except for the anti-corrosion and decorative painting work on the car body. This includes analyzing the damage to the car body, measuring the car body, shaping the sheet metal, stretch correction, stress-relief welding, as well as the assembly and adjustment of car body accessories. Below are situations that require sheet metal repair: 1. Impact-induced dents: Dents caused by impacts require sheet metal repair. The dents on sheet metal parts can be repaired using hammering or pulling methods. Different approaches are applied based on specific conditions. Naturally, the process varies with the severity of the dent, and the material of the car body must also be considered. 2. Warping or skew deformation: For warping or skew deformation of the car body, sheet metal parts may warp or skew due to impacts, scratches, or improper use. Mechanical methods or flame heating and hammering can be used to correct these deformations. 3. Breaks or punctures: For breaks or punctures, the surface of the sheet metal part can be repaired using patching methods with adhesives. Currently used adhesives include epoxy resin glue, phenolic resin glue, and copper oxide adhesives. 4. Cracks or severe local damage: In the past, these two conditions were addressed with welding or repair methods in car repairs. However, 4S shops now typically opt for direct replacement.

1

2

Share

How to Fix Sunroof Leakage in Tiguan?

The solutions for sunroof leakage in Tiguan are as follows: 1. Small sand particles or dust clogging the sunroof drainage channel: Simply clean out the clogged objects in the drainage channel. 2. The sunroof sealing strip has shifted or "lifted": Over time, the sealing strip can harden and age, leading to displacement and reduced sealing effectiveness. It is recommended to regularly replace the sunroof sealing strip. 3. Issues with the drainage system: There is a depression near the sunroof; if the drainage is poor, water may enter the interior. In such cases, it is advisable to visit a 4S shop promptly for professional inspection and repair by a technician.

19

2

Share

Is a tire pressure of 2.6 too high in summer?

Summer tire pressure of 2.6 is too high. According to the provisions and requirements of the international GBT2978-2008 standard, the standard tire pressure for standard tires is 2.4-2.5bar. A pressure of 2.7bar exceeds the maximum value of the standard tire pressure, so it is abnormal. Generally, the lower limit of the standard tire pressure for car tires is sufficient. For example, the lower limit for standard tires is 2.4bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1bar lower than the standard to avoid tire blowouts due to high temperatures. Hazards of excessive tire pressure: The friction and adhesion of the tire will decrease, affecting braking performance; It can cause steering wheel vibration and deviation, reducing driving comfort; Accelerates localized wear of the tread pattern in the center of the tire, reducing tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Causes excessive stretching and deformation of the tire cords, reducing the elasticity of the tire body and increasing the load on the car while driving; Decreases puncture resistance. When encountering sharp objects such as nails or glass on the road, they can easily penetrate the tire, and impacts can cause internal cracks and explosions, leading to blowouts.

18

3

Share

What to Do When the Built-in Tire Pressure Monitoring Sensor Runs Out of Power?

Solution for a built-in tire pressure monitoring sensor running out of power: You need to go to a repair shop to remove the tire, take off the sensor, and replace the battery. Additional information about built-in tire pressure monitoring sensors is as follows: 1. Installing a built-in tire pressure monitoring sensor requires removing the tire and mounting the sensor on the wheel hub. After installation, a vehicle wheel balance must be performed. This is usually done at a tire shop or repair facility. 2. The battery life of built-in sensors is relatively long, typically lasting 4-6 years. Replacing the battery is a complicated process, so if the built-in tire pressure monitoring sensor runs out of power, the sensor module is usually replaced directly.

2

1

Share

Is a car directly totaled if water reaches the dashboard?

Generally, it is directly totaled. A car submerged to the dashboard level is considered a fully flooded vehicle, and the owner can usually apply for a total loss. As long as the vehicle meets the total loss criteria with excessively high repair costs, the owner and the insurance company can negotiate a compensation agreement before applying for the vehicle's total loss. After the vehicle is officially totaled, the original license plate can be retained for a second time. Flooded vehicles are categorized into three scenarios: water level just above the exhaust pipe but below half the wheel height, water level exactly at half the wheel height, and water level above half the wheel height. Generally, water reaching half the wheel height can already affect the car. Below is a detailed explanation: 1. Water above the exhaust pipe: If the water only covers the exhaust pipe, promptly moving the car away is sufficient. Submerged exhaust pipes won't cause water to be sucked into the engine, and engine stalling is primarily due to water entering the engine's intake system, unrelated to the exhaust pipe being submerged. 2. Water exactly at half the wheel height: If the water reaches exactly half the wheel height, the car usually won't leak. However, prolonged soaking may cause aging of the sealing strips, leading to potential leaks. In such cases, drive the car to a 4S shop, remove the interior parts, clean, and dry them. 3. Water above half the wheel height: If the water exceeds half the wheel height, the engine may take in water, and the interior may leak. Never start the engine in this situation to avoid damaging the engine or electronic components. Additionally, if the car is flooded and starting it causes damage, the insurance company will not cover the costs.

6

3

Share

Is Electric Four-Wheel Drive the Same as Full-Time Four-Wheel Drive?

What are the symptoms of a broken car stabilizer bar?

Can Plastic Bumpers Be Repaired with Sheet Metal Work?

How to Fix Sunroof Leakage in Tiguan?

Is a tire pressure of 2.6 too high in summer?

What to Do When the Built-in Tire Pressure Monitoring Sensor Runs Out of Power?

Is a car directly totaled if water reaches the dashboard?

What does 'Remaining Points -' mean?

What is the function of installing a shark fin on a car?

Why Won't My Car Key Start the Engine?

Where Does the Car Air Conditioning Water Drain Out in Summer?