Is Chevrolet a Domestic or Joint Venture Car?

What type of engine oil should be used for the three-cylinder Excelle?

The three-cylinder Excelle uses 5W30 engine oil. The main functions of engine oil are to reduce friction and wear of moving parts, remove sludge (one of the functions of dispersants) and varnish (detergents) from the engine, neutralize acids produced by fuel and lubricant oxidation (detergents), improve the sealing of piston rings, and cool the engine by carrying away heat from moving parts. Taking the 2021 Buick Excelle Facelift 1.5L Automatic Entry-Level model as an example, the car has a length, width, and height of 4609mm, 1798mm, and 1464mm respectively, with a wheelbase of 2640mm. The manufacturer of this car is SAIC-GM Buick, classified as a compact car with a naturally aspirated intake form.

16

5

Share

What is the W gear in an automatic transmission?

Automatic transmission W stands for Winter (Snow) mode, which can be used for starting on slippery surfaces. The wheel torque is equivalent to that of second gear, helping to prevent slipping on wet or icy roads, but it is not recommended for high-speed driving. In this mode, the engine's torque is restrained and does not quickly reach its peak, reducing the likelihood of wheel spin when driving on snow and effectively preventing skidding. For automatic vehicles equipped with an ESP system, the Winter mode is not simply starting in second gear. When Winter mode is activated in an automatic transmission, the vehicle's power output is effectively controlled in real-time within a range suitable for snowy conditions. The ESP (Electronic Stability Program) system, ABS (Anti-lock Braking System), and ECU (Engine Control Unit) work together based on wheel speed and steering wheel angle, using programmed control to optimize the vehicle's driving dynamics.

18

3

Share

How to Perform a High-Speed Run with an Automatic Transmission?

Methods for performing a high-speed run with an automatic transmission: You need to place the gear in D mode, fully depress the accelerator for acceleration, and the tachometer will temporarily reach the red zone. After that, shift gears and repeat the process. However, the high-speed run should not last too long. Maintaining the RPM in the red zone for an extended period can increase wear and even cause overheating issues, potentially damaging the transmission. A high-speed run essentially allows a new car to test its maximum performance capabilities, but the RPM should not exceed two-thirds of the design limit. Performing a high-speed run can help clear oil passages, burn off carbon deposits, and improve future performance. The purpose of driving at a certain high speed is to break in components such as wheel axles and the main reducer, but the speed should be controlled between 100 km/h and 120 km/h. Avoid pushing the speed too high.

3

2

Share

Will an Automatic Transmission Car Move Without Pressing the Accelerator?

Whether an automatic transmission car will move without pressing the accelerator depends on the gear position: 1. If the gear is in P (Park) or N (Neutral), the car will not move whether you press the accelerator or not; 2. If the gear is in any position other than P or N, the car will move even without pressing the accelerator. For an automatic car in D (Drive) gear without pressing the accelerator, it is equivalent to a manual transmission car in 1st gear without pressing the clutch—this is the starting gear, and the car moves very slowly. For manual transmission models, this function is achieved through the clutch. When starting the car, if the accelerator and clutch are properly coordinated, the car will slowly move forward, also known as "creeping." If the clutch is released too quickly, the car will not only fail to move but may also stall.

8

4

Share

How to Determine When Brake Discs Need Replacement?

There are two main methods to determine if your brake discs need replacement: 1. Check the brake pad thickness: Most brake discs have wear indicators, which are three small dimples distributed on the disc surface. Use a caliper to measure the depth of these dimples; when it reaches 1.5mm (meaning the total wear depth on both sides of the disc is 3mm), the brake discs should be replaced promptly. 2. Listen for sounds: If you hear a metallic scraping or squealing noise when lightly applying the brakes, the brake pads must be replaced immediately. This noise indicates that the wear indicators on both sides of the brake pads are directly grinding against the brake disc, meaning the pads have exceeded their limit. In such cases, while replacing the brake pads, you should also inspect the brake discs. Often, the discs are already damaged when this noise occurs, and simply replacing the pads won’t stop the noise. In severe cases, the brake discs may also need replacement.

8

5

Share

What to Do If You Forget to Turn Off the Car Engine Overnight?

Forgetting to turn off the car engine overnight will not cause significant issues. In this idling state, the fuel consumption varies depending on the engine displacement, typically ranging from 0.5L to over 1L per hour. Therefore, even if the car idles all night, the total fuel consumption would be roughly equivalent to driving 100 kilometers. Simply refuel the next day. Below is some additional information: 1. Introduction: Idling is an operational state of a car where the engine runs in neutral gear. The engine speed during idling is called the idle speed, which can be adjusted by modifying the throttle opening. 2. Precautions: When the engine is running, releasing the accelerator pedal completely puts the engine in an idling state. Adjusting the idle speed should avoid sudden increases or decreases, as this can cause premature engine wear. It is best to have the idle speed adjusted at an auto repair shop.

6

5

Share

Is Chevrolet a Domestic or Joint Venture Car?

What type of engine oil should be used for the three-cylinder Excelle?

What is the W gear in an automatic transmission?

How to Perform a High-Speed Run with an Automatic Transmission?

Will an Automatic Transmission Car Move Without Pressing the Accelerator?

How to Determine When Brake Discs Need Replacement?

What to Do If You Forget to Turn Off the Car Engine Overnight?

Introduction to Car Gear Positions?

What is the idle speed of an automatic transmission car?

Can You Turn on Hazard Lights While Driving in Heavy Rain?

What Causes an Automatic Transmission to Shake and Stall at Idle?