Is Changan Ford a Domestic Car?

1 Answers
VanTyler
07/30/25 5:30am
Changan Ford is not a domestic car, but a joint venture car. Its models include: Everest, Explorer, Territory, Mondeo, Kuga, Escort, Ford Fiesta, Edge, etc. Taking the Ford Edge as an example, it is a 5-door, 5-seater midsize SUV with body dimensions of: length 4680mm, width 1930mm, height 1700mm, and a wheelbase of 2824mm. The Ford Edge is equipped with a 2.0L turbocharged engine, with a maximum power of 180 kW and a maximum torque of 390 N·m, paired with an 8-speed automatic transmission. Its drivetrain is front-engine, front-wheel drive, with MacPherson strut independent suspension at the front and multi-link independent suspension at the rear.
Was this review help?
4
1
Share
More Forum Discussions

Which Cars Have Strong Climbing Power and Are Fuel-Efficient?

Recommended vehicles with strong climbing power and fuel efficiency include the Changan CS55PLUS, Geely Haoyue, and Haval H6. Below are some methods to save fuel: 1. Control RPM: While driving, the optimal engine RPM for most fuel-injected cars is around 2200–2500. Regardless of the gear, maintain the engine RPM within this range. Too low RPM will make the car sluggish, waste fuel without moving, and damage the engine; too high RPM increases unnecessary fuel consumption and also harms the engine. 2. Maintain Speed: The most fuel-efficient driving condition is steady, straight-line driving. The most fuel-efficient speed for small-displacement cars is 60–80 km/h, while for mid-displacement cars, it is 80–100 km/h. Driving at the economic speed ensures the best fuel efficiency.
14
3
Share

Is 360-Degree Panoramic View Camera Practical?

360-degree panoramic view camera is not practical. Although the panoramic view technology is useful and has a strong sense of technology, its cost-performance ratio is not high. In fact, radar can completely replace the camera, but radar gives people a sense of insecurity, and drivers who are used to the camera may still feel worried. The following is an introduction to the 360-degree panoramic view camera: Installation method of 360-degree panoramic view camera: First, drill a hole in the car, remove the entire door panel, install the front camera on a suitable grille or emblem at the front of the car, mount the side cameras at the bottom of the left and right rearview mirrors, and then connect the wiring. Although the 360-degree panoramic view camera can be installed, the installation process is quite complicated, and the cost is not low. Impact of installing 360-degree panoramic view camera on the car: The installation process is generally invasive, requiring the removal of original car parts to some extent and connection to the original car wiring. If the wiring harness is poorly installed, minor issues like leakage may occur, while severe cases may lead to safety hazards such as fire.
13
3
Share

How long should the engine be turned off in traffic jams

Whether to turn off the engine in traffic jams generally depends on the duration. It's recommended to turn off the engine if the wait exceeds five minutes. Reasons for turning off the engine during prolonged traffic jams: Turning off the engine can save fuel. During traffic jams, drivers often feel impatient. Once the traffic eases, some may accelerate abruptly. It's advised not to rush when starting, as aggressive acceleration not only harms the vehicle but also wastes fuel. Ensure smooth movement when starting and maintain a safe distance from the vehicle ahead during traffic jams. Reasons for keeping the engine running during short traffic jams: For brief stops of one or two minutes, it's unnecessary to turn off the engine. Since the vehicle may need to move at any moment, restarting after turning off the engine is equivalent to adding startup steps, which can easily lead to waiting and honking from vehicles behind, reducing road efficiency. For short-term traffic jams, manual transmission vehicles should shift to neutral and engage the handbrake, while automatic transmission cars should shift to N gear and engage the handbrake.
8
3
Share

What are the methods to deal with rust spots on car paint?

After wiping off the rust spots, you can use a fine needle or toothpick to apply matching paint, or use a touch-up pen. It is recommended to go to a 4S shop for touch-up and polishing treatment. Polishing: The coarseness of the polishing wax used depends on the degree of oxidation of the car paint. If the particles of the sand wax are relatively coarse, it is suitable for grinding off deeper scratches, but it causes greater damage to the car paint. Although polishing has a relatively obvious effect, it should not be used frequently. Frequent polishing of the car will thin the car paint, directly affecting the service life of the car paint surface. Touch-up pen: Although the touch-up pen cannot remove the rust spots on the car paint, it can cover the rust spots to some extent. It can be said to treat the symptoms but not the root cause. It can be used for emergencies, but it is also necessary to clean the vehicle in time to prevent rust spots on the car paint surface.
9
3
Share

Bumper Damaged: Replace or Repair with Paint?

It needs to be replaced, but it also depends on the situation. Main reasons: If the front bumper is cracked, you can choose to repair or replace it based on the extent of the damage. If the cracked area is small, it can be welded and repaired. If it exceeds the repair standard, replacement is necessary. For metal bumpers, whether welding or repainting is required, professional tools and skilled techniques are essential. Typically, repairs need to be done at a 4S shop, as personal repairs may not meet the required standards. Introduction to bumpers: The car bumper is a safety device designed to absorb and mitigate external impacts, protecting the front and rear of the vehicle. The front and rear bumpers of a car are usually made of plastic, hence they are referred to as plastic bumpers. Generally, a car's plastic bumper consists of three parts: the outer panel, cushioning material, and crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed from cold-rolled thin steel sheets pressed into a U-shaped groove. The outer panel and cushioning material are attached to the crossbeam.
18
3
Share

What are the tips for selecting reference objects when driving in a straight line?

Generally, reference objects refer to trees, lamp posts, and road edge lines on both sides of the road. As long as the selected reference objects are parallel to the road markings, they can be used. Here are some precautions for driving in a straight line: 1. Vision: Don't focus only on the near distance. To keep the vehicle moving straight ahead, you must learn to look far ahead while using peripheral vision to monitor the front of the vehicle, rearview mirrors, and surrounding vehicles. 2. Speed: It's essential to control the speed when driving straight. Driving too slowly can actually cause the vehicle to veer off course. If there is a vehicle ahead, maintain a safe distance and slow down in advance if necessary. After completing straight-line driving, brake promptly. 3. Steering wheel: If the vehicle tends to drift while driving straight, some might think not moving the steering wheel will prevent drifting. However, road conditions, unbalanced wheel alignment, and uneven suspension support can all cause the steering wheel to drift. Even without moving it, the vehicle may gradually drift, so fine adjustments are necessary.
5
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.