Is C1 for automatic or manual transmission?

1 Answers
VonAlexander
07/29/25 12:42pm
C1 is a manual transmission driver's license, while C2 is for automatic transmission. However, C1 license holders can drive both manual and automatic transmission vehicles. Vehicle types permitted under C1 license: small and micro passenger vehicles, light and micro cargo vehicles, and light, small, micro special operation vehicles. Other vehicle types permitted under C1 license: C2, C3, C4. The full name of the driver's license is motor vehicle driving license, also known as 'driver's license', which is the legal document required for motor vehicle drivers. The permission to drive vehicles is granted through the issuance of a driver's license, indicating that obtaining a driver's license is a standardized procedure that must be issued by specialized authorities.
Was this review help?
9
3
Share
More Forum Discussions

How to Activate One-Touch Window Lift for Volkswagen?

Methods to activate one-touch window lift for Volkswagen: 1. Press the vehicle's one-touch start button to power on the vehicle; 2. Continuously pull the one-touch window lift button on the left door armrest; 3. While holding the window lift button, press the button on the left multifunction steering wheel; 4. Press the SET button on the right multifunction steering wheel, and the one-touch window lift function will be successfully set. Taking the new Volkswagen Teramont as an example: 1. Body dimensions: It belongs to the mid-to-large-size SUV category, with dimensions of 5039mm in length, 1989mm in width, and 1773mm in height, a wheelbase of 2980mm, a fuel tank capacity of 70 liters, and a curb weight of 2005kg. 2. Powertrain: The new Volkswagen Teramont features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 2.0L turbocharged engine, delivering a maximum horsepower of 186PS, a maximum power of 137kW, and a maximum torque of 320Nm.
5
0
Share

What is the difference between adding antifreeze and adding water?

The difference between adding antifreeze and adding water lies in the freezing point, boiling point, and function. Freezing point difference: Water freezes at 32 degrees Fahrenheit, while antifreeze freezes at -40 degrees Fahrenheit. Boiling point difference: Water boils at 100 degrees Celsius, while antifreeze boils at 108 degrees Celsius. Function difference: Water can cause rust and scale buildup in the engine's cooling system, whereas antifreeze prevents the coolant from freezing and cracking the radiator in cold winter conditions. Antifreeze is a special additive-containing coolant primarily used in liquid-cooled engine cooling systems. It offers excellent performance in preventing freezing in winter, boiling in summer, and resisting scale and corrosion year-round. Precautions for adding antifreeze to a car: Use the same brand of antifreeze. Different brands may have varying production formulas, and mixing them could lead to chemical reactions between additives, rendering them ineffective. The key indicators of antifreeze are its freezing and boiling points. Market-available antifreeze comes in specifications like -15°C, -25°C, -30°C, and -40°C. It is advisable to choose an antifreeze with a freezing point at least 10°C lower than the lowest temperature in your region.
9
5
Share

How Should Beginners Practice Driving?

Driving practice methods for beginners: 1. Starting method with handbrake. Maintain the correct driving posture, pay attention to various traffic conditions on the road ahead, and avoid looking down. The operating sequence is: step on the clutch with the left foot, gradually press the accelerator pedal with the right foot while shifting into low gear, when the engine sound changes or the car body slightly shakes, quickly release the handbrake, slightly press the accelerator pedal again, and slowly lift the clutch pedal; 2. Do not immediately release the clutch pedal, but first step on the accelerator before releasing the clutch. Because the car's resistance is greater when going uphill, more power is needed to start. The key point is the timing of releasing the handbrake. If released too early, the car may roll backward; if released too late, it may cause the engine to stall; 3. The best timing is when the clutch pedal is lifted to the semi-engaged position and the engine sound changes, release it immediately. The essentials of starting on a slope can be summarized as: when the sound changes and the car shakes slightly, pause, then quickly step on the accelerator and release the brake, adjust the accelerator according to the slope, ensuring no rolling, no jerking, and no stalling.
5
5
Share

Is It Prohibited to Stop While Wading Through Water?

It depends on the water level. If only the tires are submerged in water, the impact is minimal. However, if the water depth reaches about half of the tire height, do not force your way through. When driving through waterlogged roads, maintain a moderate speed, use low gear for manual transmissions, and avoid sudden acceleration. Do not shift gears abruptly or make sharp turns. Vehicle Wading Depth: For most compact and small cars with low chassis, the vehicle's air intake position serves as the benchmark when passing through waterlogged roads. The air intake is designed to draw in air. If the water level exceeds the height of the air intake, a significant amount of water may be sucked into the engine, causing severe damage to the vehicle. Therefore, it is crucial to pay attention to both water depth and speed when navigating through waterlogged areas. What Happens If a Vehicle Exceeds Its Wading Depth: If the water level is higher than the vehicle's wading depth, the vehicle will not be able to pass through. Insisting on proceeding may lead to engine stalling, loss of steering control, and other issues. This situation can be quite dangerous, especially if the vehicle is moving at a high speed and suddenly loses steering control. In such cases, it is essential to immediately release the accelerator pedal.
15
3
Share

Differences Between Mercedes-Benz C-Class and A-Class?

Mercedes-Benz A-Class and C-Class are different vehicle segments, with the primary differences lying in body dimensions and wheelbase, which consequently affect interior space and powertrain configurations. Relevant details are as follows: 1. The A-Class represents the entry-level model with a shorter wheelbase and compact dimensions, classified as a subcompact car. In contrast, the C-Class offers more spacious accommodations and falls under the midsize sedan category. 2. The A-Class features a rising beltline, enlarged window areas, pronounced side character lines that flow dynamically, prominently arched wheel arches, and emphasized horizontal design elements, making it particularly eye-catching on the road. 3. The A-Class maintains Mercedes-Benz's traditional technological advantages. To enhance driving comfort and safety, the new A-Class incorporates over 200 latest patents, including newly developed preventive seatbelt tensioners and airbags representing the brand's cutting-edge safety technology – such as adaptive dual-stage front airbags, seatbelt force limiters, and advanced head/thorax side airbags replacing conventional side airbags. 4. The C-Class is the best-selling model in Mercedes-Benz's lineup and offers the most comprehensive variant options. The new C-Class comes equipped with an active safety system, intelligent lighting system, preventive safety system, occupant protection system, and emergency assist features, delivering exceptional comfort, refinement, practicality, and safety.
18
0
Share

How to Tell When Car Engine Oil Needs to Be Changed?

Here are the relevant methods to determine when car engine oil needs to be changed: 1. Smell Test: Pull out the dipstick and smell it. If there is a strong sour odor, it indicates the oil has deteriorated and should be changed. 2. Finger Rub Method: Rub the extracted old oil between your thumb and index finger repeatedly. Good quality oil will feel lubricated, with few particles and no friction. If you feel impurities, poor viscosity, or even a gritty sensation, it should be changed. 3. Color Identification Method: Take a clean white filter paper and drop a few drops of old oil on it. After the oil seeps in, good quality oil will leave no powder, feel dry and smooth to the touch, and show a clear yellow infiltration zone. If it appears dark brown with impurities, it should be changed. 4. Light Inspection Method: Pull out the dipstick and hold it at a 45-degree angle under light to observe the oil droplets. If you can clearly see no particles in the droplets, the oil is in good condition. If there are many particles, it should be changed.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.