Introduction to the 5 Driving Modes of the Mercedes-Benz C-Class?

What Does Advanced Full Synthetic Engine Oil Mean?

Advanced full synthetic engine oil refers to high-quality lubricant products made entirely from PAO (Polyalphaolefin) or artificially synthesized esters, with the word "synthetic" labeled on the oil container. Relevant information is as follows: 1. Classification: Engine oils are mainly categorized into mineral oil, semi-synthetic oil, and full synthetic oil. Full synthetic oil is the highest grade of engine oil, with the main difference between full synthetic and semi-synthetic oils being that full synthetic oil has a wider temperature range and longer service life. 2. In terms of grade: Synthetic oils are mainly represented by SL, SM, and SN grade oils, while full synthetic oil represents the highest grade of engine oil, thus using the SN grade, which is the latest engine oil standard. The API on engine oil stands for the American Petroleum Institute, with grades ranging from SA, SB, SC, SD, SE, SF, SG, SH, SJ, SL, SM, to SN, with each subsequent grade representing a higher standard.

14

2

Share

Will a Car with Water-Soaked Seats Have Problems?

Water-soaked seats in a car can indeed lead to several issues. The main problems include: 1. Mold and corrosion in channels: Cars have numerous channels that are difficult to clean once water enters, leading to mold and rust over time. Examples include the inner side of door panels, air conditioning ducts, and certain structural cavities. Additionally, areas like the crankcase and differential have vent holes. 2. Bearing deterioration: Components such as the four-wheel bearings and axle grease can quickly degrade when soaked in water. 3. Damage to electronic devices: Electronic parking brakes, audio systems, and various sensors can suffer long-term damage if not repaired promptly after being waterlogged. 4. Potential total loss of the car: The most severe scenario occurs when water enters the intake manifold and the engine is forcibly started, potentially bending or breaking the connecting rods, which could render the car a total loss.

8

3

Share

Should the Terra use 92 or 95 octane gasoline?

According to the official vehicle user manual recommendation, the Terra should use 92 octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle user manual, you can also check the fuel filler cap, which will also indicate the recommended grade. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of some new technologies, the gasoline grade cannot be solely determined by the compression ratio. High compression ratio engines can also be tuned to use lower octane gasoline because, besides the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Terra occasionally uses the wrong gasoline grade, simply switch back to the correct grade after using it up. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using higher octane gasoline will not cause damage, but the increase in octane number will change the fuel's ignition point, leading to delayed combustion in the engine. This means both the engine's power output and thermal efficiency will decrease, resulting in poorer performance as experienced in real-world driving. For vehicles recommended to use higher octane gasoline, using lower octane gasoline can cause engine knocking. Because the octane number is too low, the gasoline's ignition point decreases and it may ignite prematurely during the compression stroke. If detonation occurs before the spark plug ignites, resistance will appear during the upward stroke. This resistance will cause the engine to run very unstably. If it's only mild knocking, it will just increase noise without significant damage to the engine. However, if obvious knocking is felt, it indicates the engine's condition is already very severe. The vibration not only affects driving stability but can also cause abnormal wear on the pistons and cylinders, and in severe cases, even cylinder scoring.

11

0

Share

How to Observe Car Battery Power Level?

To check the car battery power level, observe the feedback during ignition. If the ignition feels particularly laborious, it indicates the battery is undercharged. The battery warning light, if constantly illuminated, signifies the car battery is about to run out of power and requires immediate charging. Below are relevant introductions about car charging: 1. Decoding Definition: The car cannot undergo a complete power shutdown. Therefore, when using a charger, connect directly to the battery for charging without removing it, to prevent data loss that would require reinitialization. 2. Precautions: If the battery voltage is 10% lower than the rated voltage, there is a risk of undercharging. It is advisable to fully charge the battery once a month.

7

5

Share

Will 5000-grit sandpaper damage car paint?

5000-grit sandpaper can cause slight damage to car paint. Here is detailed information about automotive paint: 1. Overview: The primary function of automotive paint is to protect the car body from corrosion. Additionally, automotive paint enhances the vehicle's aesthetic appeal. Automotive paint is a type of coating. The purpose of a spray booth is to provide a clean, safe, and well-lit painting environment for automotive coating applications, ensuring that the spraying process is free from dust interference and maintains paint quality. 2. Composition: Automotive paint mainly consists of resin, pigment, additives, fillers, curing agents, solvents, etc. Metallic automotive paint typically includes reflective metal flakes (aluminum powder), while pearlescent paint usually contains mica particles.

1

2

Share

What is the representation method of tire specifications?

Automobile tire specifications indicate the size of the tire. Here is a related introduction about tire specifications: 1. Type: The types of tires include: international standard tire codes, which represent the section width and aspect ratio percentage in millimeters. This is followed by: tire type code, rim diameter (in inches), load index (permissible load mass code), and permissible speed code. 2. Specification introduction: For small cars with a displacement between 0.8-1.5, the corresponding front tire specifications range from 155/65R13-73T to 175/70R-14-77H. For large cars with a displacement between 1.6-6.0, the corresponding tire specifications range from 185/60R-14 to 245/50-R-18.

2

3

Share

Introduction to the 5 Driving Modes of the Mercedes-Benz C-Class?

What Does Advanced Full Synthetic Engine Oil Mean?

Will a Car with Water-Soaked Seats Have Problems?

Should the Terra use 92 or 95 octane gasoline?

How to Observe Car Battery Power Level?

Will 5000-grit sandpaper damage car paint?

What is the representation method of tire specifications?

How many points will be deducted for a 7-seater minivan overloaded with 3 people?

What is the reason for the transmission failure warning in the Emgrand GL?

What does the estimated total cost of 60,000 km car maintenance mean?

Is It Necessary to Repair Scratched Alloy Wheels?