In which year was the Automobile Federation established?

What are the steps to reset the maintenance light on the X-Trail?

Steps to reset the maintenance light on the X-Trail: 1. Turn off the ignition switch; 2. While pressing the clock adjustment button "set", turn on the ignition switch; 3. Release the "set" button, then press the "set" button once more; 4. Turn off the ignition switch, then turn it on again to check if the light has been reset. If not, the process must be repeated from the beginning. The X-Trail is a model under Dongfeng Nissan, with body dimensions of 4675mm in length, 1820mm in width, and 1722mm in height. The X-Trail is equipped with an intelligent all-mode 4WD system, allowing drivers to freely choose between two-wheel drive, automatic, or locked four-wheel drive modes to handle various road conditions. The X-Trail also features advanced technological equipment, such as an advanced hill start assist system, hill descent control system, electronic brake differential lock, yaw moment control system, and vehicle dynamic balance system.

19

0

Share

What does ETC mean for cars?

ETC in Chinese refers to: Electronic Toll Collection system. It is currently the most advanced road and bridge toll collection method in the world. ETC uses dedicated short-range communication between the vehicle's electronic tag installed on the windshield and the microwave antenna in the ETC lane at toll stations, combined with computer networking technology for backend bank settlement processing. This enables vehicles to pass through highway or bridge toll stations without stopping to pay tolls. The fully automatic electronic toll collection system (ETC) is one of the service functions of intelligent transportation systems. It is particularly suitable for use on highways or in busy bridge and tunnel environments. Currently, there are dedicated ETC toll lanes at highway toll stations. Vehicle owners only need to install a sensor card on the windshield and prepay funds. When passing through toll stations, there is no need for manual payment or stopping—highway tolls will be automatically deducted from the card, enabling automatic toll collection. This system takes less than two seconds per vehicle, and its lane capacity is 5 to 10 times that of manual toll lanes. Using the fully automatic electronic toll collection system can make highway toll collection paperless and cashless, fundamentally eliminating toll revenue leakage and solving financial management chaos in highway toll collection. Additionally, implementing this system can save infrastructure and management costs. Documents required for ETC application: The vehicle owner's valid ID card, the original vehicle registration certificate and a copy (the page with the most recent annual inspection stamp), and if applying on behalf of someone else, the agent's valid ID card. If applying through major bank branches, a corresponding bank debit or credit card is also required. Some banks only support ETC binding with credit cards, while others may require freezing a portion of the debit card balance as a deposit. Benefits of installing ETC: Saves time: Eliminates the hassle of waiting in queues. Green and eco-friendly: Reduces noise and exhaust emissions by eliminating stops at toll stations, lowering pollution. Reduces wear and tear: Saves costs by decreasing the frequency of vehicle acceleration and braking, reducing wear and fuel consumption. Improves efficiency: ETC lanes can theoretically increase traffic efficiency by 2-3 times, making traditional ETC systems more advanced, faster, and higher-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More policy support: The State Council explicitly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, intercity transportation cards will be widely used in key city clusters, and the proportion of vehicles equipped with ETC will significantly increase." The plan also set a target of "50% ETC usage rate for road passenger vehicles by 2020." Future possibilities: In addition to continuously improving the convenience of ETC installation and usage rates for passenger vehicles, future efforts will promote ETC use for trucks and explore deeper integration of ETC systems with vehicle-to-vehicle communication, vehicle-to-infrastructure coordination, and other smart transportation developments. This will provide comprehensive travel services for vehicle owners, meaning more application scenarios will support ETC. ETC usage precautions: The ETC transaction sensing range is 8 meters. If the vehicle ahead stops, maintain a distance of over 10 meters to prevent accidental toll payment for the other vehicle due to ETC device failure or absence. The ETC lane recognition speed limit is 20 km/h. Driving too fast may result in failed device reading and toll deduction. Unauthorized removal or movement of the OBU device, or detachment/loosening of the ETC electronic tag, may render the tag ineffective. In such cases, take it to the bank or highway service center for inspection. Non-deliberate detachment or loosening only requires reactivation. Insufficient balance on a debit card linked to ETC may cause toll deduction failure. Follow on-site staff guidance to use manual MTC lanes with cash or card payment. Excessively thick windshields may cause poor ETC signal reception. This is especially relevant for vehicles with replaced or modified windshields after accidents.

19

2

Share

What is the process for removing the grille of a Haval H6?

Haval H6 grille removal process: 1. Open the front hood and remove the 4 nuts on top of the front bumper; 2. Lift the front bumper slightly and pull it outward a bit; 3. There are 4 small screws behind the grille to remove, then only clips remain, which require a bit of force; 4. Completely remove the front bumper, then take off the grille. The Haval H6 is an urban intelligent SUV with body dimensions of 4640mm in length, 1825mm in width, and 1690mm in height, with a wheelbase of 2680mm. The Haval H6 comes standard with features such as headlight height adjustment, home light delay-off function, 4-way steering wheel adjustment, dual airbags, rear air conditioning vents, cruise control system, and intelligent voice GPS navigation system.

9

1

Share

What does the L gear in an automatic car mean?

Automatic car L gear is the low gear. Long-term use of brakes on downhill sections can easily wear out the brake pads. By shifting to L gear, you don't need to step on the brakes. The car can obtain greater power at low speeds, making it useful when climbing slopes. It is equivalent to the 1st gear in a manual transmission, providing more strength when going uphill and can be used under heavy loads. An automatic transmission generally refers to the car's automatic gear-shifting mechanism. While driving, the control system of the automatic transmission selects the appropriate gear based on the engine's speed and load, replacing the driver's subjective judgment and gear-shifting operations. A typical automatic transmission car has six gear positions, from top to bottom: P, R, N, D, S, L. The commonly used automatic gear positions are Park (P), Reverse (R), Neutral (N), and Drive (D).

2

Share

Which country is the Maxxis tire brand from?

Maxxis is a brand from Taiwan, China. Below is some extended information: Maxxis tread patterns: Maxxis has many tread patterns, which can be mainly divided into four series: Comfort Series, Sport Series, Economy Series, and SUV Series. Introduction to Maxxis MS1: The Maxxis MS1 is a comfort-oriented tire in Maxxis's passenger car series, focusing on quietness, comfort, and dry/wet road handling performance. The Maxxis MS1 features a closed shoulder design, which reduces air flow in the shoulder grooves, thereby decreasing tread pattern noise and enhancing the tire's quietness and comfort. Additionally, it has four circumferential main grooves that ensure even contact during braking, reducing tire deformation. This also improves drainage performance and anti-skid capability, ensuring wet road handling and tire durability.

2

4

Share

What is the difference between steel and aluminum alloy wheels?

The differences between steel and aluminum alloy wheels: 1. Appearance: Aluminum alloy wheels are more aesthetically pleasing; steel wheels have a more ordinary appearance. 2. Weight: Aluminum alloy wheels are lighter; steel wheels are heavier. 3. Heat dissipation: Aluminum alloy wheels have better heat dissipation performance; steel wheels have average heat dissipation. When a car is in motion, the tires and wheels generate a significant amount of heat. If this heat accumulates in the wheels, it can affect braking performance, leading to wear on the brakes, wheels, and tires. Aluminum alloy wheels can conduct this heat into the air, helping to dissipate heat from the tires and brakes, thereby increasing the vehicle's safety factor.

10

4

Share

In which year was the Automobile Federation established?

What are the steps to reset the maintenance light on the X-Trail?

What does ETC mean for cars?

What is the process for removing the grille of a Haval H6?

What does the L gear in an automatic car mean?

Which country is the Maxxis tire brand from?

What is the difference between steel and aluminum alloy wheels?

What brand is the audio system in the Jetour X70?

How to Solve the Jerking Sensation in Automatic Transmission?

Should the 1.5T Kuga use 92 or 95 octane gasoline?

What are the common faults of a car steering gear?