In the subject one test, does the right turn yield to the left turn or vice versa?

1 Answers
Eugene
07/30/25 8:59am
In the subject one test, the right turn yields to the left turn. Below is relevant information: Introduction to driver's license: The full name of a driver's license is motor vehicle driving license, also known as "driving permit". It is the certificate required by law for motor vehicle drivers. Basic introduction to subject one: Subject one refers to the driver theory test, which is conducted at the vehicle management office and is a mandatory licensing exam for driving license applicants. The test content includes the theoretical foundation of driving, road safety laws and regulations, traffic signals, traffic rules and other basic knowledge, plus local regulations. The scheduling of the driver theory test is arranged by local vehicle management offices.
Was this review help?
20
4
Share
More Forum Discussions

Is it allowed to reverse on urban roads?

Reversing is not permitted on urban roads. Regulations: According to Article 90 of the Road Traffic Safety Law of the People's Republic of China, reversing in violation of regulations (such as at railway crossings, intersections, one-way roads, bridges, sharp curves, steep slopes, or tunnels) will result in corresponding fines. Urban road traffic rules: Avoid running red lights. Major intersections in cities are equipped with red, yellow, and green traffic signals that change at regular intervals. No vehicles are allowed to run red lights. While vehicles are permitted to proceed, turning vehicles must yield to vehicles going straight and must not obstruct them.
2
3
Share

What is the actual fuel consumption of the Haima Premacy 1.8 automatic transmission?

Haima Premacy's fuel consumption per 100 kilometers is approximately 9.5 liters. Here is some extended information about fuel consumption: Reasons for increased fuel consumption: Displacement: The engine displacement has a certain impact on the car's fuel consumption, but this impact is a fixed value. Tire pressure: The car's fuel consumption is also directly related to tire pressure. When the tire pressure is too high or too low, the car's fuel consumption will increase. Road conditions: The road conditions on which the car is driven will also affect fuel consumption. Methods to reduce fuel consumption: Start slowly, do not accelerate suddenly, shift gears at low RPM, do not compete with others at traffic lights, treat any dents on the car body, close the windows when driving at high speeds to avoid increased resistance, coast in high gear, never coast in neutral as it can easily lead to steering and brake failure. Fuel consumption can vary greatly depending on personal driving habits. Drive safely, do not drive under the influence of alcohol, do not drive while fatigued, do not exceed speed limits or overload, and always wear your seatbelt while driving.
13
2
Share

What to Bring for the First Maintenance of Chevrolet Cavalier?

Items required for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle registration certificate; vehicle purchase invoice, to be taken to the designated first maintenance facility for the vehicle's initial service. Important note: Make an appointment with the 4S shop in advance. The first maintenance refers to the initial service after the new car has been driven, with the specific timing varying by vehicle, generally after driving 1,000 to 3,000 kilometers. It's essential to attend the first maintenance promptly, neither in advance nor delayed. The completion of the first maintenance signifies the end of the vehicle's break-in period, allowing it to be driven under standard load and normal speed as required by the car. The timing for the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever comes first will be the standard. First maintenance items include: Check tire condition/wear and adjust pressure if necessary. Inspect the operation of the lighting system (headlights, indicators, emergency signal lights, trunk lights, interior lights, glove box lights, dashboard warning lights, etc.). Check the operation of the windshield wipers and washers/wiper blade position/wear inspection, visual inspection of the vehicle's exterior, underbody protective components, pipes/hoses (exhaust, fuel lines, brake lines). Condition of rubber components (dust covers, bushings, spacers, etc.). Visual inspection of the condition of various control belts. Check/adjust clutch pedal height and travel. Check/adjust hand brake travel. Check and tighten chassis screws. Clean the air filter element. Time required: Approximately 2 hours to complete all tasks. The most crucial aspect of the first maintenance for a new car is changing the engine oil and oil filter. When changing the oil, the oil filter must also be replaced. The selection of engine oil must refer to the "Vehicle Use and Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not rinse the interior of the car body with water: Many people clean their cars during holidays, using water to wash the body and wiping it with a cloth. It's important to note that the interior of the car body should not be directly rinsed with water. If the floor mats are dirty, use a vacuum cleaner or take them out to brush with detergent, dry them, and then put them back. There are many holes under the rubber mats on the floor of the driver's compartment. If water enters, it won't dry by air but will flow through the holes to areas like the gearbox, causing erosion and corrosion. The best practice is to clean with a vacuum cleaner and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the antifreeze in the car is low, it's recommended to drain the antifreeze and add the same brand from the start. Since antifreeze brands differ, their chemical properties vary significantly. Different types of corrosion inhibitors can corrode each other. Different brands of antifreeze use different corrosion inhibitors, so they should not be mixed to avoid unnecessary trouble. Do not lubricate tire bolts and nuts: When the bolts on a moving car rust, it's common to oil them to restore functionality. However, some people apply lubricant to the bolts and nuts to prevent rust, which can pose a safety risk. At high speeds, the bolts and nuts may loosen or even fall off, leading to driving malfunctions. When starting an EFI car, there's no need to press the accelerator: The starter of an EFI car is different from that of a conventional car. Its fuel injection control device can automatically adjust the fuel supply based on the starter's temperature and operating conditions, ensuring a smooth start.
9
3
Share

What Type of Engine Oil is Suitable for the Audi Q3?

Audi Q3 should use fully synthetic engine oil. Below is an introduction to fully synthetic engine oil: Introduction: To achieve better lubrication, humans have chemically synthesized various types of engine oil based on base oils, which is known as chemically synthesized engine oil. Synthetic engine oil manufacturers produce different types of engine oil according to user requirements, and the composition of synthetic engine oil can be adjusted based on its intended use. Definition: According to the official explanation, synthesis refers to the process of achieving the desired molecular form through chemical reactions under human control. The largest component of engine oil is the base oil, which can be classified into five categories based on specification grades. Among these five categories, base oils of categories I, II, and III are referred to as mineral oils, while only categories IV and V can be called synthetic oils. Among these, category V base oil is polyol ester (POE), and category IV base oil is polyalphaolefin (PAO). Therefore, the simplest understanding is that engine oils blended with category IV and V base oils without the addition of mineral oils can be referred to as fully synthetic engine oils.
17
5
Share

Is it advisable to buy a car with a replaced radiator frame?

If the radiator frame is detachable and the vehicle's body frame has not been damaged, it can be purchased. If the radiator frame is not detachable, it should not be bought. Below is more information on purchasing used cars: Vehicle inspection: Check if the body is symmetrical and if the waistline of the car is even; inspect whether the factory nameplate is damaged—if it is, the vehicle has likely been in a major accident; observe if the production dates of all the glass match the manufacturing year—if not, find out why the glass was replaced; look for signs of crease repairs or screw marks on the radiator frame, left and right fenders, firewall, and wheel arches; check if the door seals are damaged; inspect the trunk floor and rear panel for signs of creasing, cutting, or welding, and ensure the rear fender and rear shock absorber bracket inner panels and internal seam lines are smooth, even, and free of welding marks; examine the dirt level on the front and rear longitudinal beams of the vehicle's chassis to see if they are roughly the same. Types of used cars not to buy: Smuggled, tax-free, or gifted vehicles; discontinued models; vehicles with outstanding payments; incomplete documentation; modified vehicles; cross-regional transactions. These types of vehicles are usually priced very low, but purchasing them can lead to various issues, so they should be avoided.
17
2
Share

What is the Difference Between O-Ring Chains and Standard Chains?

The difference between O-ring chains and standard chains lies in the fact that O-ring chains are more durable and have a relatively longer service life. Below is more information about O-ring chains: Introduction: An O-ring chain, as the name suggests, features an O-ring between the inner and outer link plates, which seals lubricant inside to maintain the chain's lubrication. Without this O-ring, it is referred to as a standard chain. Advantages: Firstly, the steel used in O-ring chains is of higher quality compared to standard chains, significantly extending the service life of O-ring chains over standard or heavy-duty chains of the same specifications. High-quality O-ring chains can achieve a service life exceeding 50,000 kilometers. Secondly, in terms of maintenance and durability, O-ring chains offer longer maintenance intervals and superior durability. Additionally, O-ring chains exhibit higher torque capacity and tensile strength, making them more robust than standard chains.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.