If one license plate is lost, should I replace a pair or just one?

What is the clutch free play?

The standard value for clutch free play is generally 0.5-2.0mm. Below is a detailed introduction to automotive clutches: 1. Composition structure: The clutch consists of four parts - the driving section, driven section, pressing mechanism, and operating mechanism. 2. Function of free play: When the clutch is properly engaged, there should be a gap between the inner end of the release lever and the release bearing, typically several millimeters. This gap is called the clutch free play. Without free play, when the friction disc wears thin, the pressure plate cannot move forward to press the driven disc, which would cause clutch slippage, reduce torque transmission capacity, result in weak vehicle power, and accelerate wear of the driven disc. 3. Adjusting free travel: The clutch pedal travel required to eliminate the clutch free play and elastic deformation of operating mechanism components is called the clutch pedal free travel. This can be adjusted by turning the adjusting fork to change the length of the release rod.

11

0

Share

What is the difference between CBS and ABS?

ABS and CBS have the following differences: CBS does not have the anti-lock function. This system can only reasonably distribute the braking force between the front and rear wheels. ABS has the anti-lock function. This system can prevent the wheels from locking up during heavy braking. What is ABS: ABS, the full name is Anti-lock Braking System. Its function is to automatically control the braking force during car braking, preventing the wheels from locking up and keeping them in a state of rolling and sliding (with a slip ratio of about 20%), ensuring maximum adhesion between the wheels and the ground. What is CBS: CBS, the full name is Combination Braking System. The CBS braking system can simultaneously brake the front and rear wheels through a single hand or foot operation, achieving higher braking efficiency by reasonably distributing the braking force between the front and rear wheels. This results in greater braking deceleration, reduces the vehicle's braking distance, and ensures that high-speed vehicles can stop safely, quickly, and smoothly.

13

0

Share

Is it mandatory to have the first car maintenance at the designated 4S store?

The first car maintenance does not have to be done at the 4S store where the car was purchased. Relevant information is introduced as follows: The 4S store where the car was purchased usually offers free maintenance services. If the vehicle has exceeded the warranty period, you can choose to go to other professional car maintenance shops for service. When visiting the 4S store for the first maintenance, you need to bring the first maintenance voucher and the vehicle maintenance manual. The content of the first car maintenance includes: 1. Changing the engine oil, oil filter, and cleaning the air filter, as well as checking whether the generator belt and wiper blades are damaged. 2. Checking whether the levels of various fluids are normal. 3. Checking whether the tire pressure is normal and whether there is any uneven wear, bulging, or damage on the tires. 4. Inspecting the car chassis, including checking for any scratches on the brake pads, brake discs, connecting rods, ball joints, and CV joints. 5. Checking whether all switches and lights in the car are working properly.

8

2

Share

What is the following distance when the speed exceeds 100 km/h?

The following distance when the speed exceeds 100 km/h should be more than 100 meters. Below is additional information on following distances: 1. When visibility is less than 200 meters: Turn on fog lights, low beams, marker lights, and front and rear position lights. The speed should not exceed 60 km/h, and the distance from the vehicle in front in the same lane should be more than 100 meters. 2. When visibility is less than 100 meters: Turn on fog lights, low beams, marker lights, front and rear position lights, and hazard warning flashers. The speed should not exceed 40 km/h, and the distance from the vehicle in front in the same lane should be more than 50 meters. 3. When visibility is less than 50 meters: Turn on fog lights, low beams, marker lights, front and rear position lights, and hazard warning flashers. The speed should not exceed 20 km/h, and you should exit the highway at the nearest exit as soon as possible.

1

0

Share

What is the actual fuel consumption of the Polo 1.6?

The actual fuel consumption of the Polo 1.6 is 5.5 liters per 100 kilometers. There are many factors that affect actual fuel consumption, and the actual comprehensive fuel consumption depends on the actual driving conditions. Method to determine fuel consumption: You can judge the fuel consumption through the car's dashboard, where F=full (representing full) and E=empty (representing empty). When the fuel tank warning light comes on, record the mileage, then note how much fuel is added. When the fuel is next depleted, record the mileage again. Subtract the initial recorded mileage from the current mileage, then divide by the amount of fuel consumed to calculate the fuel consumption. Factors affecting fuel consumption: There is a certain relationship between engine displacement and fuel consumption, but higher fuel consumption does not necessarily mean larger displacement. In a relative sense, the size of a car's engine displacement does not directly correlate with fuel consumption. Besides engine size, factors such as the car's shape, weight, and engine technology are also important factors affecting fuel consumption. Among models with the same displacement, the more advanced the engine technology, the more fuel-efficient the car will be.

13

3

Share

What is the content of the motorcycle charger wiring tutorial?

Motorcycle charger wiring tutorial: 1. Wiring: Connect the two metal clips from the charger output—the red clip is the positive pole and should be attached to the positive terminal of the battery; the black (or sometimes green or blue) clip is the negative pole and should be attached to the negative terminal of the battery. Remove all the caps from the battery to prevent the bubbles generated during charging from causing the battery case to burst. 2. Voltage adjustment: Set the charger output voltage to match the battery's rated voltage. Typically, motorcycle batteries are 12 volts, but some are 6 volts. 3. Power on: Reset the charging level to zero and turn on the charger power. 4. Increase the charging level: Gradually increase the charging level based on your desired charging speed—the lowest level is the slowest but ensures the most thorough charging. 5. Power off: When charging is complete, bubbles will appear in the battery acid, indicating that the battery is fully charged. Return the charging level to zero, turn off the charger power, and remove the metal clips.

14

2

Share

If one license plate is lost, should I replace a pair or just one?

What is the clutch free play?

What is the difference between CBS and ABS?

Is it mandatory to have the first car maintenance at the designated 4S store?

What is the following distance when the speed exceeds 100 km/h?

What is the actual fuel consumption of the Polo 1.6?

What is the content of the motorcycle charger wiring tutorial?

What is the analysis of the Mercedes-Benz G chassis?

How often should the fuel filter be replaced and at what mileage?

Is there an annual fee for ETC and how much is it per year?

What is the safe distance between cars on the highway?