How to Wash a Car with Paint Protection Film Normally?

1 Answers
DiEva
07/30/25 4:17am
Here is the relevant introduction to washing a car with paint protection film: 1. Cleaning cycle: Wash the car regularly, once a week is enough, no need to be too frequent. Do not wash the car within one week after applying the film. Dirt can be wiped clean with a soft fine towel and clean water. Corrosive dirt (such as oil stains, dyes, bird droppings, etc.) should be cleaned as much as possible within 24 hours. Neglecting them may leave marks that are difficult to remove completely. Return to the film shop for film maintenance every six months or a year, which is essentially a thorough cleaning of the film surface to remove stubborn stains accumulated over time. 2. Precautions: Avoid directly flushing the edges with a water gun to reduce the chance of peeling. Do not use acid or alkaline corrosive cleaners to clean the paint protection film.
Was this review help?
10
1
Share
More Forum Discussions

How to Remove the Wrench Symbol on the Car Display?

There are two methods to remove the wrench symbol on the car display. One is by using the buttons on the car dashboard—press and hold the reset button for 5-10 seconds to remove it. The other method involves using the car's onboard computer to clear it from the maintenance settings. The method to remove the wrench symbol on the dashboard may vary depending on the car model. Reason for the wrench symbol appearing on the display: The small wrench symbol is a maintenance reminder indicator. It lights up when the vehicle is approaching or has exceeded the scheduled maintenance mileage. At this point, you should take the car to a 4S shop for maintenance as soon as possible. Note: After the car maintenance is completed, the maintenance reminder light should be turned off immediately and reset. Otherwise, it may cause memory confusion and disrupt the car's maintenance cycle. The first maintenance for a new car can be done after six months of use or after driving 5,000 kilometers; the second maintenance can be done after one year of use or after driving 8,000 kilometers. However, the maintenance schedule is not strictly fixed. If the car is used less frequently, the maintenance interval can be appropriately extended.
20
3
Share

Does Engine Cleaner Affect the Engine?

Engine cleaner does affect the engine. Excessive use of engine cleaner can cause certain damage to the internal seals and cylinder block of the engine. If a large amount of engine cleaner residue remains inside the engine, it can also disrupt the balance of the oil composition, leading to degraded oil performance. Engine cleaner does not require high mileage for use. When carbon deposits inside the engine are not severe and sludge accumulation is minimal, adding engine cleaner can provide some cleaning effect. After cleaning, it can remove carbon deposits and sludge, enhance the fluidity of new oil, reduce engine temperature and noise, improve lubrication performance, reduce wear, and extend the engine's service life.
20
4
Share

Why Can't the Car Door Stay Closed After Opening?

The reasons why a car door won't stay closed after opening include: 1. Displacement of the door hinge or lock clip; 2. The door lock latch cannot reverse and secure properly; 3. Issues with the contact switch for door closing; 4. Insufficient height of contact installation. Car doors provide access for drivers and passengers while isolating external interference, offering some protection against side impacts and safeguarding occupants. The design requirements for car doors are: 1. Ensuring ease of entry and exit for passengers, with maximum opening angle controlled between 65 to 70 degrees; 2. No positional interference with other parts during the opening process; 3. Reliable locking when closed to prevent accidental opening while driving; 5. Good sealing performance; 6. Large transparent areas to meet lateral visibility requirements; 7. Sufficient strength and rigidity to ensure reliable operation, reduce door vibrations, enhance side collision safety, and prevent door sagging.
16
2
Share

Where is the car's carbon canister located?

The car's carbon canister is located between the engine and the fuel tank. The function of the carbon canister is to handle fuel vapors generated by the fuel tank at normal temperatures. The fuel evaporation emission system directs these vapors into the combustion process, preventing them from being released into the atmosphere, thereby reducing air pollution. The key component in this system is the activated carbon canister storage device. The carbon canister is a part of the fuel vapor emission system, also known as EVAP. Since fuel is a highly volatile liquid, the activated carbon canister is used to prevent the release of fuel vapors into the atmosphere, which would pollute the environment. The canister is filled with activated charcoal, and the fuel vapors evaporated from the fuel tank are directed into the canister for storage.
7
3
Share

How to Display the Water Temperature Gauge on the New Santana?

Methods to display the water temperature gauge on the New Santana: 1. Connect the vehicle computer with a data cable; 2. Modify the coding in the central electrical system; 3. Add a toggle switch. A 5053 data cable is required to connect to the vehicle's computer for these simple operations. The New Santana is a car produced by Shanghai Volkswagen, with body dimensions of 4473mm in length, 1706mm in width, and 1469mm in height, a wheelbase of 2603mm, a top speed of 185km/h, front disc and rear drum brakes, and equipped with 1.4L and 1.6L naturally aspirated engines.
18
4
Share

Is the Toyota Highlander a Prado?

Toyota Highlander is not a Prado. It is a large-sized SUV produced by Toyota, with a maximum wading depth of 455mm, front-wheel drive, and a top speed of 180km/h. The vehicle has a wheelbase of 2790mm, with length, width, and height dimensions of 4890mm, 1925mm, and 1720mm respectively. The Toyota Highlander is equipped with a 2.0-liter turbocharged engine, model code 8AR-FTS, delivering a maximum power of 162kW and a maximum torque of 350Nm. It features hybrid injection technology and an aluminum alloy cylinder head and block, paired with a 6-speed automatic transmission.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.