How to view the dashcam footage of Mercedes-Benz C200L?

How to Remove the Turn Signal Light on the Rearview Mirror of MG ZS?

Use a flat-head screwdriver to pry open the edge of the turn signal light on the rearview mirror, creating a small gap. Then, remove the other screw securing the turn signal light below, separating the turn signal from the rearview mirror base to finally remove it. The detailed steps are as follows: 1. Prepare all the tools needed for the entire process of removing the rearview mirror turn signal light. Use a flat-head screwdriver to pry open the gap between the rearview mirror housing and the base. Once partially pried open, gently pull the mirror housing upward to remove it. 2. Use a larger flat-head screwdriver to carefully pry open these clips, then gently pull the rearview mirror lens to separate it from the base. After removing the rearview mirror lens, you will see the screw securing the turn signal light. Use a T-10 spline to remove this screw, then remove the other screw securing the turn signal light. Keep the removed screws safely stored. 3. Remove the rearview mirror turn signal light, which is now separated from the rearview mirror base. Disconnect the wiring harness plug to completely remove the turn signal light.

9

4

Share

How to Check If You Have Any Vehicles Under Your Name?

You cannot check vehicle license plate numbers online using your ID card and name. You need to bring your ID card to the local vehicle management office for inquiry. Below is a detailed introduction on how to check vehicle information under your name: 1. Personal Vehicles: Provide the original and a copy of the vehicle owner's identity proof. 2. Company Vehicles: Provide the original and a copy of the company's organization code certificate, a power of attorney from the legal representative, and the original and a copy of the handler's ID card. 3. Required Documents: Original and a copy of the vehicle registration certificate. 4. Inspection and Law Enforcement Agencies: Present a company letter of introduction (specifying the inquiry requirements, handler's name, work ID number, etc.), the original and a copy of the handler's work ID to inquire about vehicle information. 5. Lawyers: Present the court's case acceptance notice, a company letter of introduction, and the original and a copy of the lawyer's license.

18

3

Share

How many kilometers does a new car need to replace spark plugs?

Under normal maintenance conditions, car spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is recommended to follow the user manual. The following standards can be referenced for maintenance replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps to replace spark plugs: Open the engine hood, lift the plastic cover of the engine, remove the high-voltage distributor wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. When removing them, check for any external debris such as leaves or dust, and ensure they are cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires according to the firing order, and secure the cover.

13

0

Share

Does Crystal Coating Liquid Harm Car Paint?

Crystal coating does not harm car paint. Automotive crystal coating provides reliable paint surface sealing technology, offering efficient and long-lasting protection for the car paint, preventing environmental impacts on the paint color. A water droplet experiment showed that after 12 months of use, the car paint surface remained perfectly intact, demonstrating the effectiveness of automotive crystal coating technology. Here are the benefits of automotive crystal coating: 1. Scratch resistance: With a hardness of 6H, compared to the 2H hardness of ordinary car paint, it prevents most minor scratches and has an elastic recovery function, protecting the vehicle from daily minor scratches and reducing paint surface scratches by over 70% compared to regular coatings. When external forces exceed the elastic protection range of the crystal, it usually only leaves scratches on the crystal without damaging the paint surface. 2. Corrosion resistance: The ultra-fine nano-crystal layer isolates the paint surface from the external environment, effectively preventing oxidation and resisting corrosion from bird droppings, insect residue, acid rain, etc. 3. No cracking: It resists UV rays, extreme heat, and cold, with a temperature resistance range of -50°C to 300°C, adapting to a wide range of temperature changes without cracking or peeling.

3

1

Share

What is the tire model of the Envision 28T Elite?

The tire specification for the Envision 28T Elite is 235/50R19. The first number, 235, indicates the tire width is 235MM. The 50 represents the aspect ratio of the tire's cross-section, which is 50%, meaning the height of the cross-section is 50% of the width. The letter R stands for radial tire, and 19 indicates the rim diameter is 19 inches. The Envision 28T Elite has a top speed of 205km/h and accelerates from 0 to 100km/h in 8.4 seconds. In addition to the model, tires also display the following common data: Tire carcass cord material: Represented by Chinese pinyin, such as M for cotton cord, R for rayon cord, N for nylon cord, G for steel cord, and ZG for steel radial cord. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under defined conditions. Letters from A to Z represent certified speed ratings from 4.8km/h to 300km/h. Common speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h. Rim specification: Shows the rim size compatible with the tire for practical use, such as "Standard Rim 5.00F".

10

5

Share

Why is there a 10-day rule for driving test appointments?

It takes 10 days to schedule an exam to allow students to calm down during this short period of time, consolidate these test items, and deepen their impressions. At the same time, because there are too many people applying for an exam, the number of places is limited. The following is extended information: 1. Formulation and announcement of the examination plan: Relevant departments should formulate and review the examination plans for each subject of the driving test at least 10 days before the announcement, and the announced examination plan should not be less than 5 days. 2. Notes: a. Self-appointment means that candidates freely choose the examination venue and time in the examination plan; system appointment is automatically selected by the system. b. Except for the subject one exam, when scheduling other subject exams, you need to evaluate the previous exam before continuing to schedule. c. After the appointment application is submitted, the system will notify the student by SMS 3 days in advance whether the appointment is successful, and the student can also log in to the appointment platform to directly check. d. When registering information, ensure that the mobile phone number and ID number are filled in correctly. e. Do not cancel easily after a successful appointment, otherwise it will affect the success rate and examination time of the next appointment.

20

3

Share

How to view the dashcam footage of Mercedes-Benz C200L?

How to Remove the Turn Signal Light on the Rearview Mirror of MG ZS?

How to Check If You Have Any Vehicles Under Your Name?

How many kilometers does a new car need to replace spark plugs?

Does Crystal Coating Liquid Harm Car Paint?

What is the tire model of the Envision 28T Elite?

Why is there a 10-day rule for driving test appointments?

Where is the Roewe i5 engine manufactured?

How to Deal with Water Accumulation Inside the Car?

Why does the car make a humming noise at low speeds?

Should the Air Conditioning Be Turned Off When the Car Is Turned Off?