How to Use Vehicle Cruise Control?

How to Clean the Throttle Body?

Cleaning the throttle body can be done following these steps: 1. Locate the throttle body. Open the car's engine hood and find the throttle body position. There is a black air pipe connector with a metal part secured by a metal clamp—this is the throttle body. 2. Next, use a screwdriver to loosen the metal clamp on the throttle body. You don't need to remove it completely; just loosen it sufficiently. Then, detach the plastic pipe connected to the throttle body. 3. After removing the throttle body, you can see the inside, which is covered with oil stains and carbon deposits. Take the throttle body cleaner and spray it inside a few times to dissolve the oil and carbon deposits. 4. Then, wipe it clean with a paper towel. Use your finger or another object to open the movable flap inside the throttle body and spray cleaner inside again, then wipe it clean with a paper towel. 5. Once cleaned, reassemble everything in the reverse order. Start the car and let the engine run for a while to expel any remaining debris from the throttle body.

3

0

Share

What brand of engine does the Tiggo 8 use?

The engine of the Tiggo 8 was jointly developed by Chery and AVL, but it is produced at Chery's engine production base in China, so this engine is a domestic engine. The engine model of the Tiggo 8 is SQRE4T15B. The 1.5T low-power version has a maximum power of 108 kW and a maximum torque of 210 Nm, while the 1.5T high-power version has a maximum power of 115 kW and a maximum torque of 230 Nm. The 1.6T version has a maximum power of 145 kW and a maximum torque of 290 Nm. For daily maintenance of the Tiggo 8's engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil based on mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

11

3

Share

How many liters of transmission oil does the Volkswagen Magotan approximately require?

The Magotan requires 6 liters of transmission oil for a gravity oil change. Below are two methods for changing the transmission oil: 1. The traditional gravity method involves draining the oil, similar to changing engine oil, by loosening the transmission's drain plug to release the old oil and then refilling with new oil. 2. The automatic transmission oil can also be changed using a circulation machine, which generates pressure to dynamically replace the oil in the torque converter's lubrication and cooling lines. During the circulation machine process, the old and new oil alternate much like a blood dialysis procedure. Through a viewing window, you can clearly observe the transition as the old oil changes from a deep black to a red color, eventually matching the new oil. This process takes about 10 minutes, with the entire oil change lasting approximately 90 minutes.

12

4

Share

How to Remove Car Battery Cables?

To disconnect car battery cables, follow these steps: 1. Locate the battery: Generally, car batteries are positioned in the following areas: near the spare tire in the trunk, under the driver's seat, under the passenger seat, or at the front left or right side of the engine compartment. 2. Prepare tools: Typically, a 10mm socket wrench and a flat-head screwdriver are sufficient. First, use the wrench to loosen the screw on the negative terminal. For new batteries or new cars, you can remove the negative cable by twisting it left and right a few times with your hand. For older cars, use the flat-head screwdriver to pry open the negative cable's opening and lift it a few times to remove it. 3. Wrap the negative terminal: This prevents the negative cable from returning to its original position due to internal stress, which could accidentally reconnect the negative terminal and cause unnecessary damage to the vehicle. Finally, reinstall in reverse order.

13

3

Share

Has the Mazda 2 Been Discontinued?

Mazda 2 has been discontinued. Below is a detailed introduction to the Mazda 2: 1. The Mazda 2 was produced by Changan Mazda Automobile Co., Ltd. The dimensions of this car are 3905mm in length, 1695mm in width, and 1480mm in height, with a wheelbase of 2490mm. 2. In terms of suspension, the Mazda 2 uses a MacPherson independent suspension at the front and a torsion beam non-independent suspension at the rear. 3. For power, the Mazda 2 was equipped with two engines: a 1.3-liter naturally aspirated engine and a 1.5-liter naturally aspirated engine. Both engines feature aluminum alloy cylinder heads and blocks and are paired with either a 5-speed manual transmission or a 4AT automatic transmission.

4

3

Share

How to turn off the engine without cutting power after one-button start in a car?

Do not press the brake pedal, simply press the one-button start button to keep the power on. Here is some relevant information about one-button start: 1. The one-button start device is part of a smart car, serving as a button mechanism that simplifies the starting process while also allowing engine shutdown. This device is located where the traditional key ignition would be. 2. Its functionality differs from traditional mechanical key ignition methods and conventional starting procedures. With just a gentle press of the one-button start button, you can start or shut down the engine. Even in situations where the key is out of battery or lost, the vehicle can still be started quickly. Most ignition processes require pressing the foot brake. 3. The starting method is software-based one-button start. There are three main aspects to pay attention to with the car's one-button start system (the wiring plug under the ignition switch, the position of the button, and the handling of the steering lock), and it comes with multiple functions. 4. Related benefits of one-button start: enhanced security and anti-theft performance. When the driver enters the vehicle, the car can quickly recognize them. If the owner is not inside the vehicle, it will not start.

12

4

Share

How to Use Vehicle Cruise Control?

How to Clean the Throttle Body?

What brand of engine does the Tiggo 8 use?

How many liters of transmission oil does the Volkswagen Magotan approximately require?

How to Remove Car Battery Cables?

Has the Mazda 2 Been Discontinued?

How to turn off the engine without cutting power after one-button start in a car?

Where is the handbrake of Lexus ES200 located?

How to Reset the Maintenance Wrench Light on Lavida?

Can a car be used to jump-start a motorcycle with a dead battery?

What Causes a Car to Start but Unable to Move?