How to Use the S Gear in the 14th Generation Sylphy?

1 Answers
JudahLee
07/30/25 10:38am
S gear is typically used when high torque is required, such as climbing slopes or rapid overtaking. It fully utilizes the engine's power reserve, delivering higher torque output and acceleration. However, since the S gear only delays gear shifting without altering other operational aspects, it inevitably increases the transmission load in the short term, accompanied by a rise in temperature.
Was this review help?
5
2
Share
More Forum Discussions

What Does Uneven Tire Wear Mean?

Uneven tire wear refers to the abnormal severe wear on the inner or outer side of one or more tires, meaning that a certain part of a tire wears out much faster compared to the other tires. The main cause of uneven tire wear is incorrect wheel alignment data, which requires a wheel alignment adjustment. Otherwise, it will affect the tire's service life and compromise safe driving. Methods to prevent uneven tire wear: 1. Adjust tire pressure and always maintain normal tire pressure. The recommended normal tire pressure value can be found in the manufacturer's recommendations, which may be located in the user manual or on the fuel tank cap door. 2. Regularly perform wheel balancing tests on the tires. If imbalance is detected, balance weights should be added. 3. Check whether wheel hub screws are loose.
3
1
Share

Does the Mazda 3 Axela have a mirror tilt-down function?

The Mazda 3 Axela does not come equipped with an automatic mirror tilt-down function when reversing, so it cannot be set up. The mirror tilt-down function when reversing refers to the right-side mirror automatically adjusting its angle downward when the vehicle is shifted into R gear, helping the driver see the ground situation. Method to set up automatic mirror tilt-down when reversing: After powering on the car, press and hold the mirror adjustment selection button (left or right); step on the brake and shift into R gear, at which point the selected mirror will automatically tilt down to the factory preset position. Use the 4-way adjustment button to adjust it to the desired position; step on the brake, shift into P gear, and press the mirror adjustment selection button once more to complete the setup.
6
2
Share

What is Nissan Rogue called in China?

In China, the Nissan Rogue is also known as the Luren. Rogue Configuration Overview: The new Rogue primarily features modifications to the front grille, front bumper, front and rear spoilers, and wheel arches, with added chrome accents and newly designed 18-inch aluminum alloy wheels. The interior layout remains largely consistent with the previous model, with the addition of a new navigation system. Rogue Powertrain: The Rogue continues to be equipped with a 2.5L four-cylinder engine, delivering a maximum output of 127kW/172PS and a peak torque of 237Nm, paired with an Xtronic CVT transmission. For drivetrain options, it offers front-wheel drive and optional all-wheel drive.
10
5
Share

Why Does the Steering Wheel Make a 'Clunk' Sound When Turning?

The reasons for a 'clunk' sound when turning the steering wheel include: 1. Turn signal reset: If the turn signal is activated while turning, the sound may come from the reset mechanism's recoil latch. This situation requires confirmation by the owner. 2. Steering column dust cover: If the noise comes from below the steering wheel, it might be due to the steering column dust cover. Lack of lubrication in the dust cover can cause friction noise. In this case, applying some grease inside the dust cover will eliminate the noise. 3. Clock spring (airbag spiral cable): If the noise originates from within the steering wheel, it is likely caused by the clock spring. Be gentle when removing the steering wheel or disconnect the airbag fuse to prevent accidental airbag deployment.
6
4
Share

What is the appropriate tire pressure for the Nissan NV200?

The recommended tire pressure for the Nissan NV200 is between 2.3-2.5 bar. Standard tires should be inflated to 2.4-2.5 bar, reinforced tires to 2.8-2.9 bar, and the maximum tire pressure should not exceed 3.5 bar. Introduction to low-pressure tires: Low-pressure tires have an inflation pressure of 0.1471~0.490 MPa. They are generally suitable for private vehicles, with typical inflation pressures for household cars ranging from 0.2~0.25 MPa. Introduction to high-pressure tires: High-pressure tires have an inflation pressure of 0.5~0.7 MPa. They are suitable for large trucks/buses, with typical inflation pressures around 0.5 MPa. For steel-belted radial tires, the pressure can be appropriately increased to around 0.6 MPa.
1
4
Share

Is it illegal to drive with hazard lights on?

It depends on the situation. The following are circumstances under which hazard lights can be used: 1. Visibility below 100 meters: When visibility is below 100 meters due to severe weather conditions such as heavy fog, heavy rain, or heavy snow, hazard lights must be turned on, along with low beam lights and position lights, to prevent traffic accidents. 2. Vehicle malfunction: If the vehicle cannot operate normally due to a malfunction or emergency and needs to stop to await rescue, hazard lights must be turned on. Note that whenever stopping on the road, hazard lights should be activated. If either party involved in an accident fails to turn on hazard lights, it is considered a violation and may result in fines and penalty points. Additionally, a warning triangle should be placed behind the vehicle.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.