How to Use the Roewe i5 Car Connectivity?

How to Solve the Issue of BMW 5 Series Brake Pads Not Resetting?

Press and hold the left button until "reset" appears, then continue holding to clear the warning. Relevant information is as follows: 1. Listen for sounds: If you hear a metallic scraping or squealing noise when lightly applying the brakes (which could also be due to initial break-in of newly installed brake pads), the brake pads must be replaced immediately. 2. Feel the pedal response: If you notice significantly increased pedal effort required to achieve normal braking performance, or if the brake pedal feels lower than usual during emergency braking, this indicates the brake pads may have lost their friction material and require immediate replacement.

6

1

Share

How to Handle the Annual Inspection for a Four-Year-Old Vehicle?

To proceed with the annual inspection, you need to fill out two forms: the "Motor Vehicle Driver's License Application Form" and the "Motor Vehicle Inspection Record Form." Below is a detailed introduction to the required documents for the vehicle's annual inspection (for organizations): 1. Original vehicle license. 2. Copy of the compulsory traffic insurance policy. 3. Organization code certificate of the People's Republic of China (with a fresh seal). 4. Power of attorney (with a fresh seal). 5. Copy of the agent's ID card. Notes for the vehicle's annual inspection: 1. The vehicle's exterior must not be modified. 2. Vehicles with unresolved traffic violations or those sealed by the court cannot undergo the annual inspection.

17

1

Share

Do You Need to Press the Clutch When Lightly Braking in a Manual Transmission Car?

When lightly braking in a manual transmission car, you should press the clutch. The main purpose of pressing the clutch while braking is to prevent the engine from stalling. Here is a related introduction to the function of the clutch: 1. Ensuring a smooth start: To ensure a smooth start, the engine must be started before the car begins to move. When the car starts, it accelerates suddenly from a stationary state. If the transmission system is rigidly connected to the engine, it would be impossible to start normally due to the significant inertia from stationary to moving and the large torque resistance generated by the engine. 2. Ensuring smooth gear shifting: Ensuring smooth gear shifting is another function. As for the claim that it wears out the clutch plate, one must consider the bigger picture. Some people struggle with reversing or parking and avoid using the half-clutch technique, leading to collisions. Repainting and panel beating can be more expensive. A similar example is turning the steering wheel while stationary—beginners are generally advised to know exactly when to switch directions. 3. The role of the clutch: To prevent transmission overload, the car will only start to shake when the clutch is released to a certain extent. At this point, the car needs to be given some throttle to start moving. When the car is in the half-clutch state, it won’t roll back, especially during hill starts. The clutch is also used for gear shifting. Keeping your foot on the clutch for extended periods will shorten the clutch's lifespan.

12

5

Share

Why Must Xenon Lamps Be Replaced After Several Years of Use?

Xenon lamps must be replaced after several years of use because they typically experience light decay within approximately 2 to 4 years, which can compromise driving safety. Therefore, it is advisable to replace xenon lamps soon after signs of light decay appear. The illumination principle of xenon lamps involves a quartz tube filled with xenon gas inside. High-voltage current activates the xenon gas to create an arc light. Xenon lamps have a high color temperature, appearing more white, with their greatest advantage being brightness—up to three times brighter than halogen lamps. The lifespan of xenon lamps is also significantly longer than that of halogen lamps, lasting approximately 2,500 to 3,000 hours. Installation Precautions for Automotive Xenon Headlights: Avoid installing them in areas prone to excessive heat inside the vehicle. Avoid installation near water sources, as excessive moisture can lead to leakage and aging of the ballast. They should be placed in well-ventilated locations to allow air circulation and reduce the temperature of the ballast. The distance between the ballast and the bulb should not be too far to prevent voltage drop in the circuit, which could cause the bulb to fail to light. The high-voltage wire section of the ballast should not be coiled to avoid generating excessive magnetic fields that could interfere with other electrical devices in the vehicle. Replace the original 10A fuse of the headlights with a 15-20A fuse to prevent the original fuse from blowing due to excessive current during startup.

10

2

Share

Where is the crankshaft position sensor located on the Buick GL8?

The crankshaft position sensor on the Buick GL8 is located at the rear right side of the engine, specifically at the junction between the transmission and the engine oil pan. Below is relevant information about the crankshaft position sensor: 1. Function: The primary role of the sensor is to determine the position of the crankshaft, specifically its rotation angle. It typically works in conjunction with the camshaft position sensor to establish the basic ignition timing. 2. Sensor Signal: The engine initiates ignition at the end of the compression stroke. The signals from both the crankshaft position sensor and the camshaft position sensor are used to calculate this timing. The crankshaft position sensor identifies which piston is at top dead center, while the camshaft position sensor determines which piston is in the compression stroke.

4

Share

How to Determine How Much to Turn the Steering Wheel?

Steering wheel rotation is generally determined based on the brand logo and horn markings on the steering wheel. The specific judgment methods are as follows: 1. Full turn judgment: After a full turn, the positions of the brand logo and horn remain unchanged. 2. Half-turn judgment: After a half-turn, the brand logo and horn appear upside down from the driver's perspective. Note: The principle of the steering wheel is that the rack-and-pinion gear set is enclosed in a metal tube, with each tooth end of the rack protruding outside the metal tube and connected by tie rods. The pinion is connected to the steering shaft. When the steering wheel is turned, the gear rotates, driving the rack to move. The tie rods at each tooth end of the rack are connected to the steering arm of the steering shaft.

15

4

Share

How to Use the Roewe i5 Car Connectivity?

How to Solve the Issue of BMW 5 Series Brake Pads Not Resetting?

How to Handle the Annual Inspection for a Four-Year-Old Vehicle?

Do You Need to Press the Clutch When Lightly Braking in a Manual Transmission Car?

Why Must Xenon Lamps Be Replaced After Several Years of Use?

Where is the crankshaft position sensor located on the Buick GL8?

How to Determine How Much to Turn the Steering Wheel?

Where is the lift mode for the Mercedes-Benz GLS450 air suspension?

How to Tell When Brake Discs Need Replacement

Can Changing Rims Pass the Annual Inspection?

Can Perfume in a Car Explode?