How to use the rear wiper of Audi Q5?

1 Answers
OSienna
07/30/25 4:53am
The rear wiper of the Audi Q5 is mainly located at the middle and lower end of the rear car glass. To use it, push the wiper control lever down one gear. Here are some additional details about the wiper: 1. Push the wiper control lever down two gears, and the rear wiper will spray washer fluid and wipe. Push the wiper control lever up one gear, and the front wiper will spray washer fluid and wipe once. The control gears of the front wiper can be adjusted appropriately according to the gears of the wiper control lever. 2. The rear wiper refers to the wiper on the rear windshield of the car. Rear wipers are mostly equipped on SUVs, MPVs, hatchbacks, and some liftback cars. Before installing the rear wiper, the impact of high-speed airflow must be considered—sedans have a fast wind speed during driving due to the inclined rear window, which not only hinders movement but also significantly affects the wiping performance.
Was this review help?
20
3
Share
More Forum Discussions

What is the reason for the ambient lights in the Q5L not working?

There is a circuit malfunction causing poor contact. Below is relevant information about the Audi Q5L: 1. Exterior: The new Audi Q5L measures 4765×1893×1659mm in length, width, and height, with a wheelbase of 2908mm. The front features sharp angles and a hexagonal grille, similar to the family Q7, with an overall style transitioning from the rounded look of the older Q5 to a more aggressive one. After being lengthened, the body length and wheelbase have improved compared to the older Q5. 2. Powertrain: It adopts a newly upgraded powertrain combination, featuring the third-generation EA888 engine (available in two versions: 2.0T high and low power, with the high-power version delivering a maximum power of 185kW and peak torque of 370Nm), a newly developed 7-speed Stronic 'sports car-level' transmission, and the quattro-ultra intelligent all-wheel-drive system.
17
0
Share

How much bigger is the Polo Plus compared to the Polo?

The Volkswagen Polo Plus has a wheelbase of 2564mm, while the Polo has a wheelbase of 2470mm, an increase of 94mm. Below are the relevant details about the Polo Plus: 1. Dimensions: The car measures 4053/1740/1449mm in length, width, and height, with a wheelbase of 2564mm. 2. Powertrain: It is equipped with a 1.5L naturally aspirated engine, paired with either a 5-speed manual or 6-speed automatic transmission. 3. Exterior: The Polo Plus retains the styling of the overseas version, built on the MQB-A0 platform, and adopts Volkswagen's new family design language. The overall shape is more angular and sharper compared to the current model, with a flatter appearance. The grille is flatter and connects with the headlights, enhancing the horizontal visual effect for a sportier look. The headlights feature a polygonal design with more attention to detail, incorporating a Y-shaped element inside.
1
1
Share

What are the symptoms of a bad ball joint in the eighth-generation Accord?

Because the pressurized position is in the up-and-down swinging motion during vehicle operation, the ball joint is prone to detachment. If cracks or gaps are found in the ball joint, it is recommended to replace it directly (preferably with an original factory part). The symptoms of a bad ball joint are as follows: 1. If the ball joint is bad, there will be a large gap when turning the steering wheel left or right. 2. The vehicle will produce significant abnormal noises during operation. Additional information is as follows: 1. Exterior: The eighth-generation Accord boasts generous dimensions of 4945mm in length, 1845mm in width, and 1480mm in height, along with a body design featuring rich and three-dimensional lines and first-class sheet metal craftsmanship, fully meeting Chinese consumers' demands for prestige. As an entry-level model, the 2.0L Accord has an exterior almost identical to the more expensive 2.4L model, with the same wheel design, making it hard to distinguish. Only very specific details can "reveal" its identity, such as only high-end Accord models being equipped with side mirrors with turn signals and chrome door handles. 2. Powertrain: The 2.0L Accord uses an i-VTEC engine based on the previous generation, with improvements in compression ratio, intake and exhaust valves, and combustion chamber, resulting in a certain increase in power, capable of delivering 156 horsepower and a peak torque of 189 Nm. It is paired with the same 5-speed automatic transmission as the 2.4L model.
18
0
Share

Where is the oil pressure sensor located on the Chevrolet Lova?

The oil pressure sensor on the Chevrolet Lova is located near the crankshaft pulley. Below is relevant information about the Lova RV: 1. Exterior Introduction: The Lova RV features a wide horizontal plunging front end, with a three-ridge line design on the engine hood. The front face inherits Chevrolet's family-style design, with dual grilles flanked by upward-slanting eagle-eye headlights. 2. Parameter Configuration: The 2018 Lova RV high-end model is equipped with xenon headlights, automatic headlights, front fog lights, a multifunction steering wheel, and other features. In terms of the powertrain, the 2018 Lova RV continues to be powered by a 1.5L engine, paired with either a 5-speed manual or 4-speed automatic transmission. Additionally, the new model will come standard with Start-Stop intelligent start-stop technology across all variants.
7
4
Share

Will the Roof Molding of the Eighth-Generation Accord Leak Water?

The roof molding of the eighth-generation Accord does not leak water. Below is a detailed introduction to the functions of the roof molding: 1. Aesthetic Covering: The roof molding serves an aesthetic covering purpose. Its presence or absence can indicate the welding process of the vehicle body. Experienced experts can even estimate the diameter of the weld nugget based on the width of the roof molding, which is the most important parameter reflecting the welding strength of the vehicle body. If the roof and side panels are joined using laser welding technology, due to energy focusing, the weld seam width is less than 1mm, reducing overlapping sheet materials and requiring welding on only one side of the flange (single-sided welding), resulting in good appearance quality. In this case, there is no need to install a roof molding. 2. Rainwater Guidance: The molding does not have a waterproof function but can help guide rainwater.
4
1
Share

Where is the Accord Crankshaft Position Sensor Located?

The crankshaft position sensor of the Accord is located below the engine block, above the oil pan. Here is some related information about the crankshaft position sensor: 1. Overview: The function of the crankshaft position sensor is to determine the position of the crankshaft, that is, the rotation angle of the crankshaft and the engine speed. It usually works in conjunction with the camshaft position sensor (to determine the basic ignition timing). 2. Function: The crankshaft position sensor is used to detect engine speed, hence it is also called the speed sensor; it detects the top dead center position of the piston, so it is also known as the top dead center sensor, including detecting the top dead center signal of each cylinder for ignition control and the top dead center signal of the first cylinder for sequential fuel injection control.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.