How to Use the Mercedes-Benz Vehicle Assistance System?

Differences Between 1JZ and 2JZ?

The main differences between the two are the number of turbos and the displacement. The 1JZ is a single-turbo 2.5-liter engine, while the 2JZ is a twin-turbo 3.0-liter engine. The 1JZ has a displacement of 2.5L, and the 2JZ has a displacement of 3.0L. 1JZ and 2JZ are two engine codes developed by Toyota, named 1JZ-GTE VVT-i and 2JZ-GTE, respectively. The 1JZ was introduced by Toyota in 1990, weighing 207 kg. It features an inline 6-cylinder, 2.5-liter displacement, with a compression ratio reduced to 9:1. It delivers a maximum horsepower of 280 hp and a maximum torque of 362 N·m. The 2JZ was introduced as early as 1991 and, besides the "Supra," was used in many Toyota models as a powertrain. It weighs 230 kg and features an inline 6-cylinder, 3.0-liter displacement, with a compression ratio of 8.5:1. In terms of power, it further improves upon the 1JZ, delivering a maximum horsepower of 280 hp and a maximum torque of 433 N·m in stock condition. As engines with immense modification potential, the 1JZ and 2JZ have long been favorites among car modification enthusiasts. The 1JZ can handle up to 700 hp in stock condition, while the 2JZ can handle up to 800 hp. However, due to environmental and policy reasons, both the 1JZ and 2JZ have been discontinued.

10

3

Share

What transmission does the Chevrolet Orlando use?

The Chevrolet Orlando is equipped with a 6-speed manual transmission and a 6-speed automatic manual transmission. The Chevrolet Orlando is a compact car with exterior dimensions of 4684 mm in length, 1807 mm in width, and 1628 mm in height, and a wheelbase of 2796 mm. The Chevrolet Orlando has a trunk capacity of 479 to 1520 liters and is powered by an Ecotec dual-injection turbocharged engine, with standard Start

17

5

Share

What causes the ABS light to illuminate in a Peugeot 308?

There are several conditions under which the ABS light may illuminate, each with different causes and solutions: Condition 1: ABS warning light stays on constantly (most common). Cause 1: The ABS speed sensor's sensing area is covered by mud, sludge, or other contaminants, affecting its ability to detect speed signals. This prevents the ABS computer from determining vehicle speed or wheel slip rate, thus failing to issue appropriate braking commands. Solution: Clean the speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose system wiring connections or poor ABS relay contact causing signal issues. Solution: Check all wiring connections and secure any loose connections. Condition 2: ABS warning light illuminates intermittently, turning off during acceleration. Cause: Battery voltage drops below 10.5V when multiple electrical components are in use. The light turns off when engine speed increases and voltage rises. Possible low voltage supply to ABS system due to poor connections or grounding. Solution: Check battery condition, charging system, and power supply (including voltage relay and connections). Condition 3: ABS warning light stays on after engine start until engine is turned off. Cause: Poor grounding of ABS hydraulic valve body; faulty wiring connections; or ABS computer malfunction. Solution: Loosen and retighten valve body grounding screws, clean contact surfaces if necessary; check for enlarged connector gaps; replace ABS or ABS/ASR computer if needed. Condition 4: ABS warning light illuminates during high-speed driving. Cause: ABS computer detects significant speed difference between front and rear wheels; incorrect tire or wheel specifications. Solution: Verify correct tire and wheel specifications as indicated on the fuel filler cap label. Condition 5: ABS warning light flashes intermittently. Cause: Improper brake light switch adjustment; internal contact issues in brake lights. Solution: With engine running, press brake pedal and manually push switch lever down completely, then release pedal to reset position; replace brake light switch if necessary. When the ABS warning light is on, it's recommended to avoid driving as this indicates a malfunction in the anti-lock braking system. During emergency braking, locked wheels could cause loss of vehicle control, preventing proper deceleration or steering adjustment, creating significant safety risks.

15

0

Share

What is the tire specification model?

Generally, tire specifications can be described as [tire width in mm]/[aspect ratio (percentage of tire height to width)]R[rim diameter in inches][load index][speed symbol] or [tire width in mm]/[aspect ratio][speed symbol]R[rim diameter in inches][load index]. Here is an introduction to tires: Types of tires: The international standard tire code expresses section width and aspect ratio as a percentage in millimeters. Tire specifications: There are many ways to represent tire specifications, with the four most common on the market being the British, German, metric, and American systems.

7

2

Share

What Causes Excessive Nitric Oxide in Cars?

Excessive nitric oxide in cars is caused by: clogged or failed three-way catalytic converters, leading to reduced performance. Solutions for excessive nitric oxide in cars: 1. Consistently use high-quality gasoline to ensure its purity; 2. Regularly clean the fuel injectors and three-way catalytic converter to ensure accurate fuel injection; 3. Replace the oxygen sensor. Cars produce nitric oxide because fuel combustion in vehicles occurs through spark plug ignition with air intake, which contains nitrogen and oxygen. During spark plug discharge and ignition, fuel combustion also generates significant heat, promoting a chemical reaction between nitrogen and oxygen.

18

1

Share

Can I Call for Roadside Assistance if My Tire Is Flat?

Tire is flat can call the manufacturer's free roadside assistance hotline, and the manufacturer will arrange for the nearest 4S store to provide assistance. Alternatively, you can call your insurance company to arrange for roadside assistance. Below are relevant matters regarding a flat tire: Precautions: If signs of driving with insufficient air pressure are visible on the tire (such as sidewall abrasion marks, inner liner bubbling, etc.), the tire may not be worth repairing as its structure might have been compromised and rendered unusable. Therefore, it is not advisable to continue driving with insufficient tire pressure to avoid tire damage, and severe cases may also cause rim wear.

9

0

Share

How to Use the Mercedes-Benz Vehicle Assistance System?

Differences Between 1JZ and 2JZ?

What transmission does the Chevrolet Orlando use?

What causes the ABS light to illuminate in a Peugeot 308?

What is the tire specification model?

What Causes Excessive Nitric Oxide in Cars?

Can I Call for Roadside Assistance if My Tire Is Flat?

Does wheel hub painting require registration?

What is the hierarchy of driving license classes?

Can a Leaking Wheel Hub Be Repaired?

What octane gasoline should a Bora use?